CHECK PANEL & STEERING SWITCH
The radio and display receiver assembly panel switches and steering switches are checked in the following procedure.
Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.
Enter diagnostic mode (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR).
Select "Function Check/Setting" from the "Service Menu" screen.
Select "Panel & Steering Switch" from the "Function Check/Setting I" screen.
Panel & Steering Switch Check Mode
| Display | Content |
|---|---|
| *a: Switch condition | "Pushed" is displayed when any switch is pushed |
| *b: Number of switches pushed | ·
Number of switches pushed at once is displayed ·
If more than 3 switches are pushed at once, "More than 3" is displayed |
| *c: Rotary switch direction | Direction of rotary switch is displayed |
Operate each switch and check that the switch conditions are correctly displayed.
When the "MENU" switch is pressed and held for 3 seconds or more, diagnostic mode will be canceled.
CHECK TOUCH SWITCH
The touch switches on the screen are checked in the following procedure.
Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.
Enter diagnostic mode (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR).
Select "Function Check/Setting" from the "Service Menu" screen.
Select "Touch Switch" from the "Function Check/Setting I" screen.
Touch Switch Check
Touch the display anywhere in the open area to perform the check when the "Touch Switch Check" screen is displayed.
A "+" mark is displayed where the display is touched.
The "+" mark remains on the display even after the finger is removed.
CHECK MICROPHONE
The microphone and microphone input level are checked in the following procedure.
Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.
Enter diagnostic mode (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR).
Select "Function Check/Setting" from the "Service Menu" screen.
Select "Microphone Check" from the "Function Check/Setting I" screen.
Microphone Check
| Display | Content |
|---|---|
| *a: Microphone input level meter | Monitors the microphone input level every 0.1 seconds and displays the results in 8 different levels. |
When speaking into the microphone, check that the microphone input level meter changes according to the input level.
The microphone is active at all times when this screen is displayed.
CHECK VEHICLE SIGNAL
Vehicle signals received by the radio and display receiver assembly are checked in the following procedure.
Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.
Enter diagnostic mode (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR).
Select "Function Check/Setting" from the "Service Menu" screen.
Select "Vehicle Signal" from the "Function Check/Setting I" screen.
Vehicle Signal Check Mode
| Display | Content |
|---|---|
| Battery | Battery voltage is displayed. |
| IG | Ignition switch ON/OFF state is displayed. |
| PKB | Parking brake ON/OFF state is displayed. |
| REV | Reverse signal ON/OFF state is displayed. |
| SPEED | Vehicle speed is displayed in km/h. |
| TAIL | Tail signal (Light control switch) ON/OFF state is displayed. |
| ADIM/TCAN | Brightness state DIM (with) / BRIGHT (without) is displayed. |
Only items sending vehicle signals will be displayed.
This screen displays vehicle signals input to the radio and display receiver assembly.
This screen is updated once per second when vehicle input signals change.
When the "Vehicle Signal Check Mode" screen is displayed, check all the vehicle signal conditions.
CHECK HANDS-FREE VOICE QUALITY SETTING
The hands-free volume of a "Bluetooth" compatible phone can be adjusted using the following procedure.
Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.
Enter diagnostic mode (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR).
Select "Function Check/Setting" from the "Service Menu" screen.
Select "HF Voice Quality Setting" from the "Function Check/Setting I" screen.
Hands-Free Voice Quality Setting
| *a | Numeric keypad |
| *b | Setting button |
| *c | Reset button |
If necessary, refer to the table below to adjust the voice quality type with the numeric keypad.
When adjusting the settings, use the number pad on the screen to input the voice quality type according to the table.
| Parameter | Target Phenomenon | Voice Quality Type | Positive Effects of Changing Voice Quality | Negative Effects of Changing Voice Quality |
|---|---|---|---|---|
| A
(Noise) |
The other party hears background noise when listening to your voice. | 1000 | The amount of background noise the other party hears when listening to your voice is reduced. | The volume of voice the other party hears when listening to your voice may temporarily drop. |
| B
(Noise) |
The other party hears a lot of background noise when listening to your voice. | 2000 | The amount of background noise the other party hears when listening to your voice is sharply reduced. | The volume of voice the other party hears when listening to your voice may temporarily drop. |
| C
(Echo) |
The other party hears weak echoes. | 0100 | The amount of echo is reduced (low level). | Sound quality of the other party deteriorates (low level). |
| D
(Echo) |
The other party hears strong echoes. | 0200 | The amount of echo is reduced (high level). | Sound quality of the other party deteriorates (high level). |
| Parameter | Target Phenomenon | Voice Quality Type | Positive Effects of Changing Voice Quality | Negative Effects of Changing Voice Quality |
|---|---|---|---|---|
| A+C | The other party hears background noise and weak echoes when listening to your voice. | 1100 | ·
The amount of background noise the other party hears when listening to your voice is reduced. ·
The amount of echo is reduced (low level). |
·
The volume of voice may drop temporarily. ·
Sound quality of the other party deteriorates (low level). |
| A+D | The other party hears background noise and strong echoes when listening to your voice. | 1200 | ·
The amount of background noise the other party hears when listening to your voice is reduced. ·
The amount of echo is reduced (high level). |
·
The volume of voice may drop temporarily. ·
Sound quality of the other party deteriorates (high level). |
| B+C | The other party hears a lot of background noise and weak echoes when listening to your voice. | 2100 | ·
The amount of background noise the other party hears when listening to your voice is sharply reduced. ·
The amount of echo is reduced (low level). |
·
The volume of voice may drop temporarily. ·
Sound quality of the other party deteriorates (low level). |
| B+D | The other party hears a lot of background noise and strong echoes when listening to your voice. | 2200 | ·
The amount of background noise the other party hears when listening to your voice is sharply reduced. ·
The amount of echo is reduced (high level). |
·
The volume of voice may drop temporarily. ·
Sound quality of the other party deteriorates (high level). |
The default value is "0000".
Settings will be applied when the setting button is selected.
If voice quality type values that are not in the table are input, the setting will not be applied and a positive effect may not be gained.
If the quality of phone calls decreases due to the changed settings, return the settings to "0000" by pressing the "INIT" switch.
CHECK UNIT VERSION INFORMATION
Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.
Enter diagnostic mode (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR).
Select "Service Information" from the "Service Menu" screen.
Select "Version Information" from the "Service Information" screen.
Press the "Push" switch.
Unit Version Information
| Display | Content |
|---|---|
| *a: Device name | Target device |
| *b: Manufacturer name | Manufacturer of the ECU (target device) |
| *c: Component name | Component name of the ECU (target device) |
| *d: Version | Version of the ECU (target device) |
Depending on the manufacturer, some component names and versions will be displayed differently.
CHECK SPEAKER
This function is used when checking the speaker wiring and whether the speakers are functioning properly.
Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.
Turn audio mode on and play any audio source.
This audio source will be used for the speaker check.
Enter diagnostic mode (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR).
Select "Failure Diagnosis" from the "Service Menu" screen.
Select "System Check" from the "Failure Diagnosis" screen.
Select "SP Check ON" from the "System Check Mode" screen.
Check the speaker wiring and check that the speakers are functioning properly.
Check that each speaker outputs sound from the selected audio source properly.
"SP Check OFF" is displayed during the speaker check.
Sound can be heard from the speakers around the vehicle in order beginning from a speaker on the front side.
More than one speaker may sound simultaneously depending on the speaker wiring.
Sound stops when any of the following conditions are met:
The "SP Check OFF" switch is pressed.
The ignition switch is turned off.
Diagnostic mode is turned off.
The screen is changed to another screen.
Audio mode is turned off.
CHECK SOFTWARE ERROR HISTORY
This function is used to check the cause when the radio and display receiver assembly screen is blacked out.
Check software error history.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Navigation System / Utility / Software Error History.
When an item is stored for Software Error History, record it before repairing the radio and display receiver assembly.
| Error Description | Trigger | Detail |
|---|---|---|
| Software Reset | Navi Microcomputer | Hexadecimal Number |
| Audio Microcomputer | ||
| CAN Microcomputer | ||
| No Video Signal | Front Monitor | |
| Rear Monitor | ||
| MOST Cold Restart | Always |
Software Error History can store up to 5 history data items. If a new software error occurs when 5 data items have already been stored, the oldest data is cleared and the new data is stored.
If an error that is unsupported by the GTS occurs, a "-" is displayed for the display items.
Clear software error history.
When DTCs are cleared using any of the following operations, Software Error History will be cleared as well (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR).
Cleared using the GTS.
Cleared using the system check mode screen.
Cleared using the unit check mode screen.
CHECK OPTICAL DISC ERROR HISTORY
This function is used to check the cause of an optical disc error.
Check optical disc error history.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Navigation System / Utility / Optical Disc Error History.
When an item is stored for Optical Disc Error History, record it before proceeding with troubleshooting.
| Display | Content |
|---|---|
| Error Type | Displays the type of error. |
| Device | Displays the malfunctioning device. |
| Date | Displays the date and time that the malfunction occurred. |
| Device | Component |
|---|---|
| DVD-P | Radio and display receiver assembly |
| CD-P | Not available |
| R-Seat DVD-P | Not available |
Optical Disc Error History can store up to 7 history data items. If a new optical disc error occurs when 7 data items have already been stored, the oldest data is cleared and the new data is stored.
If an error that is unsupported by the GTS occurs, a "-" or blank is displayed for the display items.
Clear optical disc error history.
When DTCs are cleared using any of the following operations, Optical Disc Error History will be cleared as well (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR).
Cleared using the GTS.
Cleared using the system check mode screen.
Cleared using the unit check mode screen.
CHECK VIDEO DEVICE CONNECTION CHECK
This function is used to detect disconnection of the video devices.
Check Video Device Connection Check.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Navigation System / Utility / Video Device Connection Check.
When an item is stored for Video Device Connection Check, record it before proceeding with troubleshooting.
DTCs are stored when errors are detected.
Depending on the vehicle, some of the items are not displayed on the "Error Detected Image Line (Type)" screen.
| Error Detected Image Line (Type) | Areas to be Checked |
|---|---|
| H/U - > Separate Display (GVIF) | Not available |
| H/U - > Full RSE (GVIF) | Not available |
| RSE - > Seat Back Display RH (GVIF) | Not available |
| RSE - > Seat Back Display LH (GVIF) | Not available |
| Rear Camera - > H/U (NTSC) | NTSC video signal between the radio and display receiver assembly and rear television camera assembly |
| IPA/BGM/PVM ECU - > Separate Display (GVIF) | Not available |
| IPA/BGM/PVM ECU - > H/U (NTSC) | Not available |
| IPA/BGM/PVM ECU - > H/U (GVIF) | Not available |
Clear video device connection check.
When DTCs are cleared using any of the following operations, Video Device Connection Check will be cleared as well (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR).
Cleared using the GTS.
Cleared using the system check mode screen.
Cleared using the unit check mode screen.