Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › 2013.08–2015.08
RM1440E _56 Audio / Visual / Telematics _056150 AUDIO / VIDEO _0274026 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  USB Audio System Recognition/Play Error  


DESCRIPTION

When a USB device or "iPod" is connected to the USB jack of the No. 1 stereo jack adapter assembly, it must have playable files. The device must also communicate with and be recognized by the radio and display receiver assembly. This diagnosis procedure is for when a device is not recognized, or files from the device cannot be played normally.

WIRING DIAGRAM

E280898E12
0.708,0.875 1.177,1.094 0.469,0.219 10 false UDO- 0.813,0.427 1.063,0.646 0.25,0.219 10 false UPI 0.708,1.75 1.125,1.969 0.417,0.219 10 false UJSG 0.656,1.323 1.073,1.542 0.417,0.219 10 false UDO+ 0.698,2.177 1.115,2.396 0.417,0.219 10 false UJSS 6.146,0.823 6.615,1.042 0.469,0.219 10 false US1- 6.125,0.385 6.521,0.604 0.396,0.219 10 false USV1 6.135,1.698 6.552,1.917 0.417,0.219 10 false UGD1 6.135,1.24 6.552,1.458 0.417,0.219 10 false US1+ 6.135,2.125 6.552,2.344 0.417,0.219 10 false USG1 1.146,0.323 1.281,0.542 0.135,0.219 10 false 1 1.156,0.76 1.292,0.979 0.135,0.219 10 false 2 1.156,1.198 1.292,1.417 0.135,0.219 10 false 3 1.156,1.625 1.302,1.823 0.146,0.198 10 false 4 1.146,2.052 1.281,2.271 0.135,0.219 10 false 5 0.146,2.646 0.563,2.813 0.417,0.167 10 false G31 0.146,2.813 2.677,3 2.531,0.188 10 false No. 1 Stereo Jack Adapter Assembly 3.281,2.313 3.969,2.552 0.688,0.24 10 false (Shielded) 5.927,0.313 6.063,0.531 0.135,0.219 10 false 1 5.917,0.74 6.052,0.958 0.135,0.219 10 false 2 5.938,1.188 6.073,1.406 0.135,0.219 10 false 3 5.927,1.625 6.063,1.844 0.135,0.219 10 false 4 5.938,2.042 6.073,2.26 0.135,0.219 10 false 5 5.875,2.583 6.24,2.75 0.365,0.167 10 false G32 5.885,2.74 7.135,3.167 1.25,0.427 10 false Radio and Display Receiver Assembly

CAUTION / NOTICE / HINT

HINT:
·

When a large amount of data is in a USB device, it may take a while to begin play.

·

When using a USB device, files that are protected by copyright cannot be played.

·

When files are not played in the sorted order, perform the following procedure before inspection.

1.

Add numbers in front of the file names.

2.

Put the files in a folder and copy the folder data to the USB device.




PROCEDURE

1.CHECK USB DEVICE OR "iPod"
a.

Disconnect the USB device or "iPod" from the No. 1 stereo jack adapter assembly.


b.

Check if playable files are present on the USB device or "iPod".

HINT:

Refer to System Description for playable files (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>SYSTEM DESCRIPTION).



c.

Check if the USB device is a compatible format or "iPod" is a compatible version.

HINT:

Refer to System Description for compatible formats and versions (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>SYSTEM DESCRIPTION).


Result:
Result Proceed to
No playable files exist, or incompatible device format or version A
Playable files exist, and compatible device format or version B




A

USB DEVICE FORMAT WAS INCOMPATIBLE, "iPod" VERSION WAS INCOMPATIBLE, OR NO PLAYABLE FILES PRESENT

B

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.

Disconnect the G32 radio and display receiver assembly connector.


b.

Disconnect the G31 No. 1 stereo jack adapter assembly connector.


c.
U181089E02
1.594,1.26 1.083,1.021 true 1.823,1.26 2.333,1.031 true 2.365,1.656 1.844,1.417 true 1.073,1.656 1.594,1.417 true 2.302,1.75 1.781,1.521 true 1.646,3.417 1.125,3.177 true 0.99,3.646 1.51,3.417 true 1.75,3.406 2.26,3.167 true 2.427,3.646 1.906,3.417 true 2.281,3.823 1.771,3.51 true 1.604,0.156 1.896,0.313 0.292,0.156 10 false G32 0.604,0.896 1.063,1.083 0.458,0.188 10 false UGD1 2.417,0.885 2.875,1.073 0.458,0.188 10 false USV1 2.438,1.51 2.896,1.698 0.458,0.188 10 false US1- 0.615,1.563 1.073,1.75 0.458,0.188 10 false US1+ 2.323,1.719 2.781,1.906 0.458,0.188 10 false USG1 1.604,2.333 1.896,2.49 0.292,0.156 10 false G31 0.719,3.042 1.177,3.229 0.458,0.188 10 false UDO- 0.698,3.604 1,3.792 0.302,0.188 10 false UPI 2.333,3.052 2.792,3.24 0.458,0.188 10 false UDO+ 2.49,3.573 2.948,3.76 0.458,0.188 10 false UJSG 2.344,3.792 2.802,3.979 0.458,0.188 10 false UJSS 0.188,0.094 0.354,0.26 0.167,0.167 10 false *a 0.188,2.156 0.385,2.323 0.198,0.167 10 false *b

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G31-1 (UPI) - G32-1 (USV1) Always Below 1 Ω
G31-2 (UDO-) - G32-2 (US1-) Always Below 1 Ω
G31-3 (UDO+) - G32-3 (US1+) Always Below 1 Ω
G31-4 (UJSG) - G32-4 (UGD1) Always Below 1 Ω
G31-5 (UJSS) - G32-5 (USG1) Always Below 1 Ω
G31-1 (UPI) - Body ground Always 10 kΩ or higher
G31-2 (UDO-) - Body ground Always 10 kΩ or higher
G31-3 (UDO+) - Body ground Always 10 kΩ or higher
G31-4 (UJSG) - Body ground Always 10 kΩ or higher
G31-5 (UJSS) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
*b Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)



OK

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (NO. 1 STEREO JACK ADAPTER ASSEMBLY POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (NO. 1 STEREO JACK ADAPTER ASSEMBLY POWER SOURCE)
a.

Reconnect the G32 radio and display receiver assembly connector.


b.
U181086E02
1.458,2.083 0.802,2.469 true 1.948,2.073 2.604,2.458 true 1.563,0.698 1.854,0.854 0.292,0.156 10 false G31 0.115,0.083 0.344,0.302 0.229,0.219 10 false *a 0.469,2.49 0.76,2.646 0.292,0.156 10 false UPI 2.646,2.49 3.052,2.646 0.406,0.156 10 false UJSG

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G31-1 (UPI) - G31-4 (UJSG) Ignition switch ACC 5 V


Text in Illustration
*a Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)



OK

4.FORMAT USB DEVICE OR RESTORE "iPod" AND RECHECK

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

4.FORMAT USB DEVICE OR RESTORE "iPod" AND RECHECK
a.

Delete all files in the USB device or "iPod" and format/restore it.


b.

Save the data again and check if it can be played on the in-vehicle device.

NOTICE:

Formatting a USB device or restoring an "iPod" erases all music on the device. Ensure that backup music data is available before performing this operation.


OK:

Malfunction disappears.




OK

END

NG

5.REPLACE USB DEVICE OR "iPod"
5.REPLACE USB DEVICE OR "iPod"
a.

Turn the ignition switch off.

HINT:

When this malfunction occurs, it is necessary to turn off the ignition switch to make it possible for the vehicle to recognize a new device when it is connected.



b.

Turn the ignition switch to ACC.


c.

Connect a known good USB device or "iPod" to the No. 1 stereo jack adapter assembly.


HINT:
·

If the malfunction occurred when a USB device was in use, use another USB device for the inspection. If the malfunction occurred when an "iPod" was in use, use another "iPod" for the inspection.

·

Refer to System Description for compatible formats and versions (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>SYSTEM DESCRIPTION).




NEXT

6.CHECK USB DEVICE OR "iPod"
6.CHECK USB DEVICE OR "iPod"
a.

Check if a USB device or "iPod" is recognized by the radio and display receiver assembly, and if information such as track, artist and album names are displayed on the screen.

OK:

Malfunction disappears.




OK

USB DEVICE OR "iPod" WAS INCOMPATIBLE OR DEFECTIVE

NG

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE