Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM › from 2013.08
RM1440E _56 Audio / Visual / Telematics _056151 PARK ASSIST / MONITORING _0274043 TOYOTA PARKING ASSIST-SENSOR SYSTEM J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM  Park / Neutral Position Switch Circuit  


DESCRIPTION

This circuit sends the park/neutral position switch assembly signals to the clearance warning ECU assembly.

WIRING DIAGRAM

E200005E08
0.344,1.563 1.406,2 1.063,0.438 10 false from IG1 No. 1 Relay 2.042,1.729 2.948,1.917 0.906,0.188 10 false ECU-IG NO. 1 5.594,1.292 5.823,1.469 0.229,0.177 10 false PL 4.438,1.208 4.667,1.385 0.229,0.177 10 false PL 3.26,1.469 3.49,1.646 0.229,0.177 10 false RB 4.448,1.729 4.677,1.906 0.229,0.177 10 false RL 3.177,2.385 3.583,2.563 0.406,0.177 10 false B51 5.542,2.385 5.948,2.563 0.406,0.177 10 false F78 5.396,1.208 5.563,1.385 0.167,0.177 10 false 7 3.063,1.469 3.229,1.646 0.167,0.177 10 false 2 5.604,1.823 5.833,2 0.229,0.177 10 false RL 5.365,1.74 5.656,1.917 0.292,0.177 10 false 23 4.708,1.208 4.875,1.385 0.167,0.177 10 false 6 4.74,1.729 4.906,1.906 0.167,0.177 10 false 1 5.49,2.552 7.021,2.906 1.531,0.354 10 false Clearance Warning ECU Assembly 3.167,2.563 4.948,2.938 1.781,0.375 10 false Park/Neutral Position Switch Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.
E179071E18
1.656,1.115 0.854,0.76 true 2.052,1.177 2.844,0.615 true 2.125,1.552 2.313,1.823 true 0.583,0.667 0.823,0.854 0.24,0.188 10 false RB 0.146,0.094 0.385,0.281 0.24,0.188 10 false *a 2.333,1.844 2.667,2.031 0.333,0.188 10 false PL 2.896,0.531 3.135,0.719 0.24,0.188 10 false RL

Disconnect the B51 park/neutral position switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (RL) - 2 (RB) Shift lever in R Below 1 Ω
Shift lever not in R 10 kΩ or higher
2 (RB) - 6 (PL) Shift lever in P Below 1 Ω
Shift lever not in P 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Park/Neutral Position Switch Assembly)

Result
Result Proceed to
OK A
NG (for A750F) B
NG (for A750E) C



A

2.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BATTERY)

B

C

2.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BATTERY)
a.
U180998E02
1.833,1.281 2.26,0.844 2.26,0.844 2.563,0.844 true 0.073,0.042 0.323,0.229 0.25,0.188 10 false *a 1.635,0.552 2.01,0.927 0.375,0.375 10 false B51 2.583,0.792 2.823,0.938 0.24,0.146 10 false RB

Disconnect the B51 park/neutral position switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B51-2 (RB) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Park/Neutral Position Switch Assembly)



OK

3.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the F78 clearance warning ECU assembly connector.


b.

Disconnect the B51 park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F78-7 (PL) - B51-6 (PL) Always Below 1 Ω
F78-23 (RL) - B51-1 (RL) Always Below 1 Ω
F78-7 (PL) - Body ground Always 10 kΩ or higher
F78-23 (RL) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR