Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM › from 2013.08
RM1440E _56 Audio / Visual / Telematics _056151 PARK ASSIST / MONITORING _0274043 TOYOTA PARKING ASSIST-SENSOR SYSTEM J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM  Front Clearance Sonar Sensor LH Circuit  


DESCRIPTION

The No. 1 ultrasonic sensor sends and receives ultrasonic waves. Based on the received wave, the sensor calculates the approximate distance between the vehicle and the obstacle, and sends the distance value as a signal to the clearance warning ECU assembly.

WIRING DIAGRAM

E282883E07
4.823,2.229 5.198,2.5 0.375,0.271 10 false F78 4.813,1.76 5.188,2.031 0.375,0.271 10 false E6 4.583,1.625 4.844,1.917 0.26,0.292 10 false 12 4.813,1.26 5.188,1.531 0.375,0.271 10 false S6 2.333,1.24 2.708,1.51 0.375,0.271 10 false S 4.583,1.146 4.802,1.354 0.219,0.208 10 false 13 2.542,1.146 2.76,1.354 0.219,0.208 10 false 2 2.333,1.75 2.708,2.021 0.375,0.271 10 false E 2.542,1.625 2.76,1.833 0.219,0.208 10 false 1 4.813,2.365 6.021,2.74 1.208,0.375 10 false Clearance Warning ECU Assembly 1.104,2.229 1.479,2.5 0.375,0.271 10 false E2 1.094,2.385 2.729,2.781 1.635,0.396 10 false No. 1 Ultrasonic Sensor (Front Corner Sensor LH)

PROCEDURE

1.INSPECT NO. 1 ULTRASONIC SENSOR (FRONT CORNER SENSOR LH)
a.

Remove the No. 1 ultrasonic sensor (front corner sensor LH) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR(for Front)>REMOVAL).


b.

Inspect the No. 1 ultrasonic sensor (front corner sensor LH) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR(for Front)>INSPECTION).



OK

2.CHECK HARNESS AND CONNECTOR (FRONT CORNER SENSOR LH - CLEARANCE WARNING ECU ASSEMBLY)

NG

REPLACE NO. 1 ULTRASONIC SENSOR (FRONT CORNER SENSOR LH)

2.CHECK HARNESS AND CONNECTOR (FRONT CORNER SENSOR LH - CLEARANCE WARNING ECU ASSEMBLY)
a.

Disconnect the E2 No. 1 ultrasonic sensor (front corner sensor LH) connector.


b.

Disconnect the F78 clearance warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E2-1 (E) - F78-12 (E6) Always Below 1 Ω
E2-2 (S) - F78-13 (S6) Always Below 1 Ω
E2-1 (E) - Body ground Always 10 kΩ or higher
E2-2 (S) - Body ground Always 10 kΩ or higher




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR