Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM › from 2013.08
RM1440E _56 Audio / Visual / Telematics _056151 PARK ASSIST / MONITORING _0274043 TOYOTA PARKING ASSIST-SENSOR SYSTEM J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM  Front Clearance Sonar Sensor RH Circuit  


DESCRIPTION

The No. 1 ultrasonic sensor sends and receives ultrasonic waves. Based on the received wave, the sensor calculates the approximate distance between the vehicle and the obstacle, and sends the distance value as a signal to the clearance warning ECU assembly.

WIRING DIAGRAM

E282883E08
4.823,2.198 5.198,2.469 0.375,0.271 10 false F78 4.813,1.75 5.188,2.021 0.375,0.271 10 false E5 4.594,1.646 4.813,1.854 0.219,0.208 10 false 33 4.823,1.25 5.198,1.521 0.375,0.271 10 false S5 2.354,1.229 2.729,1.5 0.375,0.271 10 false S 4.594,1.167 4.813,1.375 0.219,0.208 10 false 34 2.542,1.167 2.76,1.375 0.219,0.208 10 false 2 2.354,1.729 2.729,2 0.375,0.271 10 false E 2.531,1.635 2.75,1.844 0.219,0.208 10 false 1 4.813,2.344 6.042,2.698 1.229,0.354 10 false Clearance Warning ECU Assembly 1.104,2.198 1.479,2.469 0.375,0.271 10 false E1 1.094,2.354 2.885,2.75 1.792,0.396 10 false No. 1 Ultrasonic Sensor (Front Corner Sensor RH)

PROCEDURE

1.INSPECT NO. 1 ULTRASONIC SENSOR (FRONT CORNER SENSOR RH)
a.

Remove the No. 1 ultrasonic sensor (front corner sensor RH) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR(for Front)>REMOVAL).


b.

Inspect the No. 1 ultrasonic sensor (front corner sensor RH) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR(for Front)>INSPECTION).



OK

2.CHECK HARNESS AND CONNECTOR (FRONT CORNER SENSOR RH - CLEARANCE WARNING ECU ASSEMBLY)

NG

REPLACE NO. 1 ULTRASONIC SENSOR (FRONT CORNER SENSOR RH)

2.CHECK HARNESS AND CONNECTOR (FRONT CORNER SENSOR RH - CLEARANCE WARNING ECU ASSEMBLY)
a.

Disconnect the E1 No. 1 ultrasonic sensor (front corner sensor RH) connector.


b.

Disconnect the F78 clearance warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E1-1 (E) - F78-33 (E5) Always Below 1 Ω
E1-2 (S) - F78-34 (S5) Always Below 1 Ω
E1-1 (E) - Body ground Always 10 kΩ or higher
E1-2 (S) - Body ground Always 10 kΩ or higher




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR