Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM › from 2013.08
RM1440E _56 Audio / Visual / Telematics _056151 PARK ASSIST / MONITORING _0274043 TOYOTA PARKING ASSIST-SENSOR SYSTEM J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM  Rear Clearance Sonar Sensor RH Circuit  


DESCRIPTION

The No. 1 ultrasonic sensor sends and receives ultrasonic waves. Based on the received wave, the sensor calculates the approximate distance between the vehicle and the obstacle, and sends the distance value as a signal to the clearance warning ECU assembly.

WIRING DIAGRAM

E282887E12
4.802,2.177 5.177,2.448 0.375,0.271 10 false F78 4.802,1.729 5.156,1.938 0.354,0.208 10 false E1 4.583,1.656 4.802,1.865 0.219,0.208 10 false 17 4.802,1.25 5.177,1.521 0.375,0.271 10 false S1 2.354,1.729 2.729,2 0.375,0.271 10 false E 1.24,1.75 1.615,2.021 0.375,0.271 10 false S 4.573,1.167 4.792,1.375 0.219,0.208 10 false 18 2.5,1.646 2.719,1.854 0.219,0.208 10 false 1 1.094,1.656 1.313,1.865 0.219,0.208 10 false 2 4.792,2.344 6.135,2.792 1.344,0.448 10 false Clearance Warning ECU Assembly 1.083,2.167 1.458,2.438 0.375,0.271 10 false P1 1.083,2.333 2.667,2.792 1.583,0.458 10 false No. 1 Ultrasonic Sensor (Rear Corner Sensor RH)

PROCEDURE

1.REPLACE NO. 1 ULTRASONIC SENSOR (REAR CORNER SENSOR RH)
a.

Remove the No. 1 ultrasonic sensor (rear corner sensor RH) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR(for Rear)>REMOVAL).


b.

Inspect the No. 1 ultrasonic sensor (rear corner sensor RH) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR(for Rear)>INSPECTION).



OK

2.CHECK HARNESS AND CONNECTOR (REAR CORNER SENSOR RH - CLEARANCE WARNING ECU ASSEMBLY)

NG

REPLACE NO. 1 ULTRASONIC SENSOR (REAR CORNER SENSOR RH)

2.CHECK HARNESS AND CONNECTOR (REAR CORNER SENSOR RH - CLEARANCE WARNING ECU ASSEMBLY)
a.

Disconnect the P1 No. 1 ultrasonic sensor (rear corner sensor RH) connector.


b.

Disconnect the F78 clearance warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P1-1 (E) - F78-17 (E1) Always Below 1 Ω
P1-2 (S) - F78-18 (S1) Always Below 1 Ω
P1-1 (E) - Body ground Always 10 kΩ or higher
P1-2 (S) - Body ground Always 10 kΩ or higher




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR