Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM1440E _57 Power Source / Network _056154 NETWORKING _0274052 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B1287  Back Door ECU Communication Stop  


DESCRIPTION

This DTC is stored when LIN communication between the multiplex network door ECU (back door P/W) and main body ECU (multiplex network body ECU) stops for 10 seconds or more.

DTC Code DTC Detection Condition Trouble Area
B1287 No communication between the multiplex network door ECU (back door P/W) and main body ECU (multiplex network body ECU) for 10 seconds or more
·

Multiplex network door ECU (back door P/W)

·

Main body ECU (multiplex network body ECU)

·

Harness or connector



WIRING DIAGRAM

C218161E02
5.405,0.397 5.828,0.561 0.422,0.164 10 MPX1 1.536,0.397 1.880,0.561 0.344,0.164 10 LIN2 5.15,0.324 5.338,0.488 0.187,0.164 10 16 1.961,0.324 2.148,0.488 0.187,0.164 10 16 5.405,0.721 5.828,0.885 0.422,0.164 10 BDR 4.141,0.604 4.992,0.768 0.851,0.164 10 DOOR BACK 2.478,0.723 3.265,0.887 0.787,0.164 10 from Battery 0.539,0.695 0.686,0.858 0.146,0.164 10 A 0.539,0.855 2.292,1.221 1.752,0.367 10 Main Body ECU (Multiplex Network Body ECU) 1.912,1.359 3.260,1.523 1.347,0.164 10 from IG1 No. 1 Relay 4.129,1.256 5.045,1.420 0.916,0.164 10 ECU-IG NO. 1 4.384,0.924 4.877,1.088 0.493,0.164 10 ECU-B 5.221,0.648 5.338,0.812 0.117,0.164 10 1 5.405,1.041 5.828,1.205 0.422,0.164 10 BECU 5.221,0.968 5.338,1.132 0.117,0.164 10 7 5.405,1.367 5.828,1.531 0.422,0.164 10 SIG 5.221,1.294 5.338,1.458 0.117,0.164 10 8 5.405,1.687 5.828,1.851 0.422,0.164 10 GND 4.819,2.102 5.241,2.266 0.422,0.164 10 V2 4.819,2.266 6.730,2.588 1.911,0.321 10 Multiplex Network Door ECU (Back Door P/W) 5.221,1.614 5.338,1.778 0.117,0.164 10 6

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the ignition switch off to troubleshoot:

Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.

·

Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.



HINT:

When communication between the multiplex network door ECU (back door P/W) and main body ECU (multiplex network body ECU) stops, DTC B2325 is also stored.


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1287 is not output.




OK

NG

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - MULTIPLEX NETWORK DOOR ECU)
3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - MULTIPLEX NETWORK DOOR ECU)
a.

Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Disconnect the V2 multiplex network door ECU (back door P/W) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-16 (LIN2) - V2-16 (MPX1) Always Below 1 Ω
A-16 (LIN2) or V2-16 (MPX1) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - BATTERY AND BODY GROUND)
a.
U150320E03
2.188,1.302 2.406,1.51 2.406,1.51 2.51,1.51 true 2.146,1.063 2.365,0.854 2.365,0.854 2.469,0.854 true 2.083,1.344 2.302,1.802 2.302,1.802 2.406,1.802 true 1.292,1.073 1.052,0.698 1.052,0.698 0.948,0.698 true 0.635,1.146 0.844,1.323 0.208,0.177 10 false V2 0.094,0.073 0.302,0.25 0.208,0.177 10 false *a 2.583,1.438 3,1.615 0.417,0.177 10 false BECU 2.531,0.771 2.948,0.948 0.417,0.177 10 false BDR 0.573,0.625 0.917,0.802 0.344,0.177 10 false GND 2.448,1.708 2.865,1.885 0.417,0.177 10 false SIG

Disconnect the V2 multiplex network door ECU (back door P/W) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V2-6 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
V2-1 (BDR) - Body ground Always 11 to 14 V
V2-7 (BECU) - Body ground Always 11 to 14 V
V2-8 (SIG) - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Rear view of wire harness connector
(to Multiplex Network Door ECU [Back Door P/W])


OK

5.REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE MULTIPLEX NETWORK DOOR ECU
a.

Temporarily replace the multiplex network door ECU (back door P/W) with a new or normally functioning one (See page Vehicle Interior>DOOR LOCK>BACK DOOR LOCK>REMOVAL).



NEXT

6.CLEAR DTC
6.CLEAR DTC

NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1287 is not output.




OK

END (MULTIPLEX NETWORK DOOR ECU IS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)