Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM1440E _57 Power Source / Network _056154 NETWORKING _0274052 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B1206  P/W Master Switch Communication Stop  


DESCRIPTION

This DTC is stored when LIN communication between the multiplex network master switch assembly and main body ECU (multiplex network body ECU) stops for 10 seconds or more.

DTC Code DTC Detection Condition Trouble Area
B1206 No communication between the multiplex network master switch assembly and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Multiplex network master switch assembly

·

Main body ECU (multiplex network body ECU)

·

Harness or connector



WIRING DIAGRAM

C361639E01
1.469,0.406 1.813,0.583 0.344,0.177 10 false LIN2 1.979,0.26 2.198,0.448 0.219,0.188 10 false 16 5.063,0.229 5.281,0.417 0.219,0.188 10 false 17 5.063,0.667 5.281,0.854 0.219,0.188 10 false 11 5.063,1.125 5.281,1.313 0.219,0.188 10 false 12 0.667,1 0.833,1.177 0.167,0.177 10 false A 0.656,1.188 2.313,1.583 1.656,0.396 10 false Main Body ECU (Multiplex Network Body ECU) 3.115,0.813 3.927,1.01 0.813,0.198 10 false from Battery 4.573,0.979 5.021,1.167 0.448,0.188 10 false DOOR 5.417,0.385 5.781,0.563 0.365,0.177 10 false LIN1 5.417,0.823 5.573,1 0.156,0.177 10 false B 5.417,1.26 5.792,1.448 0.375,0.188 10 false GND 4.563,1.875 4.802,2.052 0.24,0.177 10 false h1 4.583,2.083 6.646,2.458 2.063,0.375 10 false Multiplex Network Master Switch Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the ignition switch off to troubleshoot:

Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.

·

Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.



HINT:

When communication between the multiplex network master switch and main body ECU (multiplex network body ECU) stops, DTC B2325 is also stored.


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1206 is not output.




OK

NG

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - MULTIPLEX NETWORK MASTER SWITCH)
3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - MULTIPLEX NETWORK MASTER SWITCH)
a.

Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Disconnect the h1 multiplex network master switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-16 (LIN2) - h1-17 (LIN1) Always Below 1 Ω
A-16 (LIN2) or h1-17 (LIN1) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH - BATTERY AND BODY GROUND)
a.
U150220E02
1.042,1.438 0.833,1.656 0.833,1.656 0.698,1.656 true 1.177,1.438 1.063,1.875 1.063,1.875 0.927,1.875 true 0.094,0.063 0.271,0.26 0.177,0.198 10 false *a 0.552,1.583 0.698,1.76 0.146,0.177 10 false B 0.573,1.802 0.906,1.979 0.333,0.177 10 false GND 0.448,1.094 0.688,1.271 0.24,0.177 10 false h1

Disconnect the h1 multiplex network master switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
h1-12 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
h1-11 (B) - Body ground Always 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Multiplex Network Master Switch Assembly)


OK

5.REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
a.

Temporarily replace the multiplex network master switch assembly with a new or normally functioning one (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL).



NEXT

6.CLEAR DTC
6.CLEAR DTC

NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1206 is not output.




OK

END (MULTIPLEX NETWORK MASTER SWITCH IS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)