Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM1440E _57 Power Source / Network _056154 NETWORKING _0274052 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2327  Lost Communication with Back Door Power Window ECU (Abnormal Power Supply)  B2328  Back Door Power Window ECU Communication Malfunction  


DESCRIPTION

·

DTC B2327 is stored when LIN communication between the multiplex network door ECU (back door P/W) and back door power window regulator motor assembly stops for 10 seconds or more.

·

DTC B2328 is stored when a malfunction in the LIN communication bus between the multiplex network door ECU (back door P/W) and back door power window regulator motor assembly is detected consecutively 3 times.

DTC Code DTC Detection Condition Trouble Area
B2327 No communication between the multiplex network door ECU (back door P/W) and back door power window regulator motor assembly for 10 seconds or more.
·

Multiplex network door ECU (back door P/W)

·

Back door power window regulator motor assembly

·

Harness or connector


B2328 The multiplex network door ECU (back door P/W) detects a malfunction in the LIN communication bus between the multiplex network door ECU (back door P/WU) and back door power window regulator motor assembly consecutively 3 times.
·

Multiplex network door ECU (back door P/W)

·

Back door power window regulator motor assembly

·

Harness or connector




WIRING DIAGRAM

C361646E01
1.417,0.385 1.844,0.573 0.427,0.188 10 false MPX2 1.427,0.823 1.833,1.01 0.406,0.188 10 false BDR2 1.625,1.26 1.833,1.458 0.208,0.198 10 false E4 1.938,0.26 2.135,0.417 0.198,0.156 10 false 11 1.969,0.688 2.125,0.854 0.156,0.167 10 false 6 1.979,1.125 2.094,1.292 0.115,0.167 10 false 1 5.177,0.219 5.292,0.385 0.115,0.167 10 false 9 5.177,0.667 5.292,0.833 0.115,0.167 10 false 2 5.177,1.146 5.292,1.313 0.115,0.167 10 false 1 5.427,0.365 5.729,0.563 0.302,0.198 10 false LIN 5.417,0.802 5.573,1 0.156,0.198 10 false B 5.406,1.229 5.76,1.427 0.354,0.198 10 false GND 0.656,1.813 1.021,2.01 0.365,0.198 10 false W10 0.677,2.031 2.458,2.396 1.781,0.365 10 false Multiplex Network Door ECU (Back Door P/W) 4.875,1.813 5.156,1.99 0.281,0.177 10 false W9 4.875,2.042 6.594,2.406 1.719,0.365 10 false Back Door Power Window Regulator Motor Assembly

CAUTION / NOTICE / HINT

NOTICE:

When using the intelligent tester with the ignition switch off to troubleshoot:

Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B2327 or B2328 is not output.




OK

NG

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - BACK DOOR POWER WINDOW REGULATOR MOTOR)
3.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - BACK DOOR POWER WINDOW REGULATOR MOTOR)
a.

Disconnect the W10 multiplex network door ECU (back door P/W) connector.


b.

Disconnect the W9 back door power window regulator motor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W10-11 (MPX2) - W9-9 (LIN) Always Below 1 Ω
W10-6 (BDR2) - W9-2 (B) Always Below 1 Ω
W10-1 (E4) - W9-1 (GND) Always Below 1 Ω
W10-1 (E4) - Body ground Always Below 1 Ω
W9-1 (GND) - Body ground Always Below 1 Ω
W10-11 (MPX2) or W9-9 (LIN) - Body ground Always 10 kΩ or higher
W10-6 (BDR2) or W9-2 (B) - Body ground Always 10 kΩ or higher




OK

4.REPLACE BACK DOOR POWER WINDOW REGULATOR MOTOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE BACK DOOR POWER WINDOW REGULATOR MOTOR ASSEMBLY
a.

Temporarily replace the back door power window regulator motor assembly with a new or normally functioning one (See page Vehicle Exterior>WINDOW / GLASS>BACK DOOR POWER WINDOW MOTOR>REMOVAL).



NEXT

5.CLEAR DTC
5.CLEAR DTC

NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B2327 or B2328 is not output.




OK

END (BACK DOOR POWER WINDOW REGULATOR MOTOR IS DEFECTIVE)

NG

REPLACE MULTIPLEX NETWORK DOOR ECU