Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2013.08
RM1440E _57 Power Source / Network _056154 NETWORKING _0274053 CAN COMMUNICATION SYSTEM U

NETWORKING  CAN COMMUNICATION SYSTEM  TERMINALS OF ECU  


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:
·

Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or any doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





JUNCTION CONNECTOR


a.

NO. 1 JUNCTION CONNECTOR

U150328E03
4.385,1.906 4.323,1.906 4.323,1.906 4.063,1.344 true 3.958,1.354 4.323,2.208 4.323,2.208 4.385,2.208 true 3.854,1.292 4.302,0.792 4.302,0.792 4.375,0.792 true 3.781,1.271 4.292,0.49 4.292,0.49 4.375,0.49 true 3.667,1.354 2.927,2.167 2.927,2.167 2.854,2.167 true 3.594,1.26 2.958,0.385 2.958,0.385 2.885,0.385 true 4.396,1.844 4.99,2.021 0.594,0.177 10 false CANH*a 4.406,2.167 4.99,2.344 0.583,0.177 10 false CANH*b 4.385,0.417 4.927,0.615 0.542,0.198 10 false CANL*a 4.406,0.719 4.979,0.906 0.573,0.188 10 false CANH*c 2.313,2.104 2.844,2.281 0.531,0.177 10 false CANL*b 2.365,0.313 2.896,0.49 0.531,0.177 10 false CANL*c 2.552,1.188 2.875,1.365 0.323,0.177 10 false A36

Text in Illustration
*a for Skid Control ECU (Master Cylinder Solenoid) *b for No. 2 Junction Connector
*c for Combination Meter Assembly - -

No. 1 Junction Connector Wiring Color Connect to
A36-1 (CANH) B Skid control ECU (master cylinder solenoid)
A36-4 (CANL) W
A36-2 (CANH) GR No. 2 junction connector
A36-5 (CANL) W
A36-3 (CANH) L Combination meter assembly
A36-6 (CANL) W


b.

NO. 2 JUNCTION CONNECTOR

i.

V1 bus:

U180978E02
4.656,1.552 4.594,1.552 4.594,1.552 4.083,1.802 true 4.677,2.25 4.542,2.24 4.542,2.24 4.073,1.969 true 3.958,1.792 4.604,1.208 4.604,1.208 4.667,1.208 true 3.875,1.781 4.604,0.875 4.604,0.875 4.677,0.875 true 3.771,1.781 2.635,0.542 2.635,0.542 2.552,0.542 true 3.688,1.781 2.635,0.875 2.635,0.875 2.563,0.875 true 3.979,1.969 4.625,2.542 4.625,2.542 4.688,2.542 true 3.885,1.958 4.594,2.885 4.594,2.885 4.667,2.885 true 3.771,2 2.625,3.26 2.625,3.26 2.552,3.26 true 3.677,2 2.625,2.896 2.625,2.896 2.552,2.896 true 3.5,1.781 2.615,1.24 2.615,1.24 2.542,1.24 true 3.49,1.99 2.604,2.469 2.604,2.469 2.531,2.469 true 4.719,0.802 5.417,0.979 0.698,0.177 10 false CANH*c 4.719,1.146 5.427,1.313 0.708,0.167 10 false CANH*b 4.719,1.49 5.323,1.677 0.604,0.188 10 false CANH*a 1.969,0.469 2.563,0.646 0.594,0.177 10 false CANH*d 1.969,0.802 2.583,0.979 0.615,0.177 10 false CANH*e 1.969,1.167 2.573,1.323 0.604,0.156 10 false CANH*f 4.719,2.813 5.406,2.99 0.688,0.177 10 false CANL*c 4.719,2.469 5.396,2.646 0.677,0.177 10 false CANL*b 4.719,2.167 5.302,2.365 0.583,0.198 10 false CANL*a 1.99,3.198 2.563,3.375 0.573,0.177 10 false CANL*d 1.979,2.813 2.563,2.99 0.583,0.177 10 false CANL*e 1.99,2.396 2.573,2.594 0.583,0.198 10 false CANL*f 3.458,0.781 3.781,0.958 0.323,0.177 10 false F59

Text in Illustration
*a for No. 4 Junction Connector *b for Main Body ECU (Multiplex Network Body ECU)
*c for No. 1 Junction Connector *d for DLC3
*e for Airbag Sensor Assembly *f for Steering Angle Sensor (Spiral Cable Sub-assembly)

No. 2 Junction Connector Wiring Color Connect to
F59-1 (CANH) SB No. 4 junction connector
F59-12 (CANL) W
F59-2 (CANH) R Main body ECU (multiplex network body ECU)
F59-13 (CANL) W
F59-3 (CANH) GR No. 1 junction connector
F59-14 (CANL) W
F59-4 (CANH) V DLC3
F59-15 (CANL) W
F59-5 (CANH) Y Airbag sensor assembly
F59-16 (CANL) W
F59-7 (CANH) G Steering angle sensor (spiral cable sub-assembly)
F59-18 (CANL) W


ii.

MS bus (w/ Seat Position Memory):

U180977E02
4.729,2.365 4.677,2.365 4.677,2.365 3.875,1.469 true 4.771,0.281 4.719,0.281 4.719,0.281 3.865,1.271 true 4.729,2 4.677,2 4.677,2 3.948,1.469 true 4.719,0.688 4.667,0.688 4.667,0.688 3.969,1.271 true 4.75,1.698 4.677,1.698 4.677,1.698 4.083,1.458 true 4.813,0.969 4.729,0.969 4.729,0.969 4.073,1.281 true 4.823,1.625 5.417,1.844 0.594,0.219 10 false CANN*a 4.833,0.906 5.427,1.115 0.594,0.208 10 false CANP*a 4.833,1.927 5.438,2.125 0.604,0.198 10 false MSCL*b 4.792,0.615 5.417,0.813 0.625,0.198 10 false MSCH*b 4.813,2.292 5.354,2.5 0.542,0.208 10 false CANN*c 4.813,0.219 5.406,0.438 0.594,0.219 10 false CANP*c 2.417,1.167 2.74,1.344 0.323,0.177 10 false F82

Text in Illustration
*a for Main Body ECU (Multiplex Network Body ECU) *b for Combination Meter Assembly
*c for Front Power Seat Switch LH - -

No. 2 Junction Connector Wiring Color Connect to
F82-1 (CANP) B Main body ECU (multiplex network body ECU)
F82-12 (CANN) W
F82-2 (MSCH) LG Combination meter assembly
F82-13 (MSCL) W
F82-3 (CANP) L Front power seat switch LH
F82-14 (CANN) W



c.

NO. 3 JUNCTION CONNECTOR

U180979E02
3.5,1.781 2.615,1.208 2.615,1.208 2.542,1.208 true 3.49,2 2.604,2.552 2.604,2.552 2.531,2.552 true 4.656,1.552 4.594,1.552 4.594,1.552 4.083,1.792 true 4.677,2.25 4.542,2.25 4.542,2.25 4.063,1.99 true 3.958,1.802 4.604,1.208 4.604,1.208 4.667,1.208 true 3.875,1.792 4.604,0.875 4.604,0.875 4.677,0.875 true 3.667,1.792 2.635,0.865 2.635,0.865 2.552,0.865 true 3.969,2 4.625,2.542 4.625,2.542 4.688,2.542 true 3.865,2 4.594,2.885 4.594,2.885 4.667,2.885 true 3.688,2 2.625,2.885 2.625,2.885 2.552,2.885 true 3.406,1.781 2.615,1.542 2.615,1.542 2.542,1.542 true 3.385,1.99 2.604,2.229 2.604,2.229 2.531,2.229 true 4.719,0.792 5.281,0.979 0.563,0.188 10 false CANH*c 4.719,1.146 5.271,1.323 0.552,0.177 10 false CANH*b 4.719,1.5 5.26,1.698 0.542,0.198 10 false CANH*a 1.969,0.792 2.5,0.969 0.531,0.177 10 false CANH*d 1.969,1.146 2.5,1.344 0.531,0.198 10 false CANH*e 1.969,2.469 2.479,2.656 0.51,0.188 10 false CANL*e 1.969,1.49 2.469,1.656 0.5,0.167 10 false CANH*f 4.719,2.823 5.25,3.01 0.531,0.188 10 false CANL*c 4.719,2.479 5.292,2.667 0.573,0.188 10 false CANL*b 4.719,2.167 5.271,2.365 0.552,0.198 10 false CANL*a 1.979,2.813 2.49,3 0.51,0.188 10 false CANL*d 1.99,2.167 2.5,2.365 0.51,0.198 10 false CANL*f 3.458,0.771 3.781,0.948 0.323,0.177 10 false F60

Text in Illustration
*a for No. 4 Junction Connector *b for ECM
*c for Four Wheel Drive Control ECU (for 4WD) *d for Power Steering ECU Assembly
*e for Yaw Rate Sensor Assembly *f for Air Conditioning Amplifier Assembly

No. 3 Junction Connector Wiring Color Connect to
F60-1 (CANH) GR No. 4 junction connector
F60-12 (CANL) W
F60-2 (CANH) V ECM
F60-13 (CANL) W
F60-3 (CANH) G Four wheel drive control ECU*1
F60-14 (CANL) W
F60-5 (CANH) L Power steering ECU assembly
F60-16 (CANL) W
F60-7 (CANH) R Yaw rate sensor assembly
F60-18 (CANL) W
F60-8 (CANH) B Air conditioning amplifier assembly
F60-19 (CANL) W

*1: for 4WD



d.

NO. 4 JUNCTION CONNECTOR

U150280E03
4.469,3.854 4.375,3.854 4.375,3.854 3.583,4.688 true 4.469,4.135 4.375,4.135 4.375,4.135 3.677,4.698 true 4.5,5.479 4.406,5.479 4.406,5.479 3.583,4.885 true 4.5,5.188 4.406,5.188 4.406,5.188 3.667,4.865 true 3.563,1.667 4.375,2.229 4.375,2.229 4.448,2.229 true 3.563,1.49 2.677,0.656 2.677,0.656 2.604,0.656 true 4.531,5.115 5.104,5.323 0.573,0.208 10 false CANL*a 4.531,5.406 5.094,5.615 0.563,0.208 10 false CANL*b 4.531,4.073 5.135,4.281 0.604,0.208 10 false CANH*a 4.531,3.781 5.156,3.99 0.625,0.208 10 false CANH*b 2.25,4.677 2.542,4.844 0.292,0.167 10 false G13 4.5,2.156 5.073,2.333 0.573,0.177 10 false CANL*c 2.052,0.583 2.583,0.781 0.531,0.198 10 false CANH*c 2.354,1.417 2.656,1.583 0.302,0.167 10 false G14

Text in Illustration
*a for No. 3 Junction Connector *b for No. 2 Junction Connector
*c for Radio and Display Receiver Assembly (w/ Radio and Display Receiver Assembly) - -

No. 4 Junction Connector Wiring Color Connect to
G13-5 (CANH) GR No. 3 junction connector
G13-16 (CANL) W
G13-6 (CANH) SB No. 2 junction connector
G13-17 (CANL) W
G14-6 (CANH) P Radio and display receiver assembly*1
G14-17 (CANL) W

*1: w/ Radio and Display Receiver Assembly




CHECK DLC3


a.
U181095E02
1.958,0.917 2.125,0.438 2.125,0.438 2.271,0.438 true 1.594,0.906 1.479,0.448 1.479,0.448 1.417,0.448 true 1.948,1.479 1.802,1.854 1.802,1.854 1.74,1.854 true 2.344,1.458 2.406,1.823 2.406,1.823 2.458,1.823 true 0.208,1.146 0.49,1.323 0.281,0.177 10 false F13 2.323,0.375 2.771,0.552 0.448,0.177 10 false CANH 1.125,0.354 1.365,0.51 0.24,0.156 10 false CG 2.521,1.76 2.833,1.938 0.313,0.177 10 false BAT 1.333,1.771 1.719,1.948 0.385,0.177 10 false CANL

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F13-6 (CANH) - F13-14 (CANL) V - W Ignition switch off 54 to 69 Ω
F13-6 (CANH) - F13-4 (CG) V - W-B Ignition switch off 200 Ω or higher
F13-14 (CANL) - F13-4 (CG) W - W-B Ignition switch off 200 Ω or higher
F13-6 (CANH) - F13-16 (BAT) V - GR Ignition switch off 6 kΩ or higher
F13-14 (CANL) - F13-16 (BAT) W - GR Ignition switch off 6 kΩ or higher



CHECK ECM


U180631E02
2.25,2.073 2.604,2.375 2.604,2.375 2.729,2.375 false 2,2.063 2.146,2.552 2.146,2.552 2.26,2.552 true 5.802,1.365 5.969,0.708 5.969,0.708 6.094,0.708 true 0.417,2.073 0.729,2.49 0.729,2.49 0.854,2.49 true 0.667,0.354 0.958,0.531 0.292,0.177 10 false F51 1.708,0.365 1.979,0.542 0.271,0.177 10 false F50 3.208,0.365 3.479,0.542 0.271,0.177 10 false B36 4.208,0.365 4.479,0.542 0.271,0.177 10 false B37 5.292,0.365 5.552,0.542 0.26,0.177 10 false B38 6.333,0.354 6.625,0.531 0.292,0.177 10 false B39 2.781,2.271 3.198,2.438 0.417,0.167 10 false CANL 6.167,0.646 6.375,0.813 0.208,0.167 10 false E1 0.906,2.406 1.365,2.573 0.458,0.167 10 false BATT 2.333,2.469 2.76,2.635 0.427,0.167 10 false CANH

a.

Disconnect the B38, F50 and F51 ECM connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F50-32 (CANH) - F50-31 (CANL) V - W Ignition switch off 108 to 132 Ω
F50-32 (CANH) - B38-12 (E1) V - BR Ignition switch off 200 Ω or higher
F50-31 (CANL) - B38-12 (E1) W - BR Ignition switch off 200 Ω or higher
F50-32 (CANH) - F51-24 (BATT) V - L Ignition switch off 6 kΩ or higher
F50-31 (CANL) - F51-24 (BATT) W - L Ignition switch off 6 kΩ or higher



CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY, MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


U180724E02
1.625,1.531 1.823,1.292 1.823,1.292 1.906,1.292 false 1.625,1.854 1.823,1.698 1.823,1.698 1.906,1.698 false 1.625,2.188 1.823,2.385 1.823,2.385 1.906,2.385 false 5.031,8.135 5.281,7.708 5.281,7.708 5.385,7.708 true 3.031,8.135 2.781,7.708 2.781,7.708 2.677,7.708 true 3.573,4.594 3.458,5.177 3.458,5.177 3.375,5.177 true 3.49,4.604 3.354,5 3.354,5 3.271,5 true 1.365,4.615 1.51,5.167 1.51,5.167 1.594,5.167 true 1.458,4.594 1.615,4.99 1.615,4.99 1.698,4.99 true 0.896,1.635 1.104,1.792 0.208,0.156 10 false 2F 1.083,3.896 1.365,4.052 0.281,0.156 10 false F10 0.896,2.229 1.104,2.385 0.208,0.156 10 false 2D 5.865,1.552 6.073,1.708 0.208,0.156 10 false 2B 5.865,2.26 6.073,2.417 0.208,0.156 10 false 2C 1.073,2.771 1.281,2.927 0.208,0.156 10 false 2E 3.75,1.354 3.865,1.5 0.115,0.146 10 false A 1.927,1.219 2.198,1.365 0.271,0.146 10 false F8 1.927,1.635 2.198,1.781 0.271,0.146 10 false F9 1.927,2.323 2.198,2.469 0.271,0.146 10 false F10 3.635,3.896 3.917,4.052 0.281,0.156 10 false F9 1.125,5.198 1.344,5.354 0.219,0.156 10 false 2F 1.885,6.438 2.104,6.594 0.219,0.156 10 false 2B 4.938,6.438 5.156,6.594 0.219,0.156 10 false 2C 3.51,7.677 3.646,7.833 0.135,0.156 10 false A 3.948,5.208 4.146,5.365 0.198,0.156 10 false 2D 5.896,5.208 6.094,5.365 0.198,0.156 10 false 2E 5.927,3.896 6.208,4.052 0.281,0.156 10 false F8 5.427,7.646 5.844,7.802 0.417,0.156 10 false BECU 2.24,7.656 2.656,7.813 0.417,0.156 10 false GND1 2.833,5.104 3.385,5.26 0.552,0.156 10 false CANL*A 2.708,4.927 3.302,5.083 0.594,0.156 10 false CANH*A 1.719,4.927 2.302,5.083 0.583,0.156 10 false CANP*B 1.635,5.094 2.25,5.25 0.615,0.156 10 false CANN*B

Text in Illustration
*A for V1 Bus *B for MS Bus (w/ Seat Position Memory)

a.

Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

for V1 Bus
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F9-14 (CANH) - F9-13 (CANL) R - W Ignition switch off 54 to 69 Ω
F9-14 (CANH) - A-11 (GND1) R - None Ignition switch off 200 Ω or higher
F9-13 (CANL) - A-11 (GND1) W - None Ignition switch off 200 Ω or higher
F9-14 (CANH) - A-30 (BECU) R - None Ignition switch off 6 kΩ or higher
F9-13 (CANL) - A-30 (BECU) W - None Ignition switch off 6 kΩ or higher

for MS Bus (w/ Seat Position Memory)
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F10-9 (CANP) - F10-10 (CANN) B - W Ignition switch off 108 to 132 Ω
F10-9 (CANP) - A-11 (GND1) B - None Ignition switch off 200 Ω or higher
F10-10 (CANN) - A-11 (GND1) W - None Ignition switch off 200 Ω or higher
F10-9 (CANP) - A-30 (BECU) B - None Ignition switch off 6 kΩ or higher
F10-10 (CANN) - A-30 (BECU) W - None Ignition switch off 6 kΩ or higher



CHECK SKID CONTROL ECU (MASTER CYLINDER SOLENOID)


U149993E03
3.865,1.25 4.052,1.573 4.052,1.573 4.156,1.573 true 3.885,1.063 4.094,0.438 4.094,0.438 4.188,0.438 true 2.906,1.208 3.083,1.667 3.083,1.667 3.188,1.667 true 2.729,1.229 2.563,1.625 2.563,1.625 2.458,1.625 true 4.323,0.365 4.75,0.531 0.427,0.167 10 false CANL 4.208,1.5 4.635,1.667 0.427,0.167 10 false CANH 3.229,1.594 3.625,1.76 0.396,0.167 10 false +BM1 2.031,1.563 2.479,1.729 0.448,0.167 10 true GND1 1.948,0.927 2.167,1.094 0.219,0.167 10 false A6

a.

Disconnect the A6 skid control ECU (master cylinder solenoid) connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
A6-11 (CANH) - A6-25 (CANL) B - W Ignition switch off 54 to 69 Ω
A6-11 (CANH) - A6-1 (GND1) B - W-B Ignition switch off 200 Ω or higher
A6-25 (CANL) - A6-1 (GND1) W - W-B Ignition switch off 200 Ω or higher
A6-11 (CANH) - A6-2 (+BM1) B - B Ignition switch off 6 kΩ or higher
A6-25 (CANL) - A6-2 (+BM1) W - B Ignition switch off 6 kΩ or higher



CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY


U149879E03
3.771,1.25 3.677,0.208 3.677,0.208 3.573,0.208 true 4.771,1.438 4.896,1.823 4.896,1.823 4.979,1.823 true 3.677,1.24 3.365,0.385 3.365,0.385 3.271,0.385 true 3.479,1.271 3.052,0.615 3.052,0.615 2.969,0.615 true 3.146,0.125 3.563,0.292 0.417,0.167 10 false CANH 2.844,0.302 3.25,0.469 0.406,0.167 10 false CANL 2.583,0.51 2.938,0.688 0.354,0.177 10 false GND 5.042,1.74 5.219,1.917 0.177,0.177 10 false B 3.938,0.281 4.24,0.448 0.302,0.167 10 false F42

a.

Disconnect the F42 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Condition Specified Condition
F42-11 (CANH) - F42-12 (CANL) B - W Ignition switch off 54 to 69 Ω
F42-11 (CANH) - F42-14 (GND) B - W-B Ignition switch off 200 Ω or higher
F42-12 (CANL) - F42-14 (GND) W - W-B Ignition switch off 200 Ω or higher
F42-11 (CANH) - F42-21 (B) B - V Ignition switch off 6 kΩ or higher
F42-12 (CANL) - F42-21 (B) W - V Ignition switch off 6 kΩ or higher



CHECK COMBINATION METER ASSEMBLY


U181003E02
2.417,0.979 2.167,0.729 2.167,0.729 2.083,0.729 true 3.021,0.99 2.854,0.438 2.854,0.438 2.771,0.438 true 4.729,1 4.969,0.75 4.969,0.75 5.094,0.75 true 4.594,0.969 4.813,0.479 4.813,0.479 4.938,0.479 true 4.333,1.219 4.448,1.583 4.448,1.583 4.573,1.583 true 4.49,1.208 5.083,1.365 5.083,1.365 5.208,1.365 true 3.438,0.313 3.708,0.479 0.271,0.167 10 false F14 1.854,0.656 2.042,0.844 0.188,0.188 10 false E1 2.635,0.344 2.771,0.531 0.135,0.188 10 false B 5.125,0.677 5.802,0.844 0.677,0.167 10 false CANH*A 4.969,0.406 5.635,0.563 0.667,0.156 10 false CANL*A 4.604,1.5 5.24,1.667 0.635,0.167 10 false MSCL*B 5.25,1.281 5.896,1.438 0.646,0.156 10 false MSCH*B

Text in Illustration
*A for V1 Bus *B for MS Bus (w/ Seat Position Memory)

a.

Disconnect the F14 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

for V1 Bus
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F14-1 (CANH) - F14-2 (CANL) L - W Ignition switch off 108 to 132 Ω
F14-1 (CANH) - F14-20 (E1) L - W-B Ignition switch off 200 Ω or higher
F14-2 (CANL) - F14-20 (E1) W - W-B Ignition switch off 200 Ω or higher
F14-1 (CANH) - F14-15 (B) L - L Ignition switch off 6 kΩ or higher
F14-2 (CANL) - F14-15 (B) W - L Ignition switch off 6 kΩ or higher

for MS Bus (w/ Seat Position Memory)
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F14-23 (MSCH) - F14-24 (MSCL) LG - W Ignition switch off 108 to 132 Ω
F14-23 (MSCH) - F14-20 (E1) LG - W-B Ignition switch off 200 Ω or higher
F14-24 (MSCL) - F14-20 (E1) W - W-B Ignition switch off 200 Ω or higher
F14-23 (MSCH) - F14-15 (B) LG - L Ignition switch off 6 kΩ or higher
F14-24 (MSCL) - F14-15 (B) W - L Ignition switch off 6 kΩ or higher



CHECK AIRBAG SENSOR ASSEMBLY


U180939E02
2.865,0.917 3.146,0.24 3.146,0.24 3.198,0.24 true 6.438,1.188 6.677,1.51 6.677,1.51 6.76,1.51 true 3.052,1.292 3.188,1.646 3.188,1.646 3.25,1.646 true 2.604,1.281 2.49,1.635 2.49,1.635 2.427,1.635 true 2.406,0.156 2.688,0.313 0.281,0.156 10 false F33 5.781,0.219 6.052,0.385 0.271,0.167 10 false F13 3.271,0.167 3.719,0.313 0.448,0.146 10 false CANH 3.281,1.583 3.729,1.729 0.448,0.146 10 false CANL 2.219,1.563 2.417,1.708 0.198,0.146 10 false E1 6.802,1.448 7.115,1.594 0.313,0.146 10 false BAT

a.

Disconnect the F33 airbag sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F33-13 (CANH) - F33-22 (CANL) Y - W Ignition switch off 54 to 69 Ω
F33-13 (CANH) - F33-25 (E1) Y - W-B Ignition switch off 200 Ω or higher
F33-22 (CANL) - F33-25 (E1) W - W-B Ignition switch off 200 Ω or higher
F33-13 (CANH) - F13-16 (BAT) Y - GR Ignition switch off 6 kΩ or higher
F33-22 (CANL) - F13-16 (BAT) W - GR Ignition switch off 6 kΩ or higher



CHECK STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY)


U149956E03
2.26,1.156 2.594,0.563 2.594,0.563 2.677,0.563 true 1.969,1.156 1.635,0.563 1.635,0.563 1.542,0.563 true 2.375,1.156 2.708,0.792 2.708,0.792 2.792,0.792 true 2.146,1.167 2.344,0.375 2.344,0.375 2.438,0.375 true 2.719,0.458 3.146,0.625 0.427,0.167 10 false CANL 1.198,0.5 1.51,0.667 0.313,0.167 10 false BAT 2.865,1.073 3.177,1.24 0.313,0.167 10 false F19 2.833,0.719 3.146,0.896 0.313,0.177 10 false ESS 2.5,0.26 2.948,0.427 0.448,0.167 10 false CANH

a.

Disconnect the F19 steering angle sensor (spiral cable sub-assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F19-4 (CANH) - F19-3 (CANL) G - W Ignition switch off 54 to 69 Ω
F19-4 (CANH) - F19-2 (ESS) G - W-B Ignition switch off 200 Ω or higher
F19-3 (CANL) - F19-2 (ESS) W - W-B Ignition switch off 200 Ω or higher
F19-4 (CANH) - F19-6 (BAT) G - L Ignition switch off 6 kΩ or higher
F19-3 (CANL) - F19-6 (BAT) W - L Ignition switch off 6 kΩ or higher



CHECK YAW RATE SENSOR ASSEMBLY


U150050E03
2.333,0.844 2.438,1.656 2.438,1.656 2.552,1.656 true 2.219,0.875 1.958,1.573 1.958,1.573 1.865,1.573 true 2.427,0.885 2.906,1.583 2.906,1.583 3,1.583 true 5.635,1.354 5.781,1.563 5.781,1.563 5.885,1.563 true 2.063,0.313 2.354,0.458 0.292,0.146 10 false F36 5.01,0.313 5.302,0.458 0.292,0.146 10 false F13 2.573,1.583 2.99,1.771 0.417,0.188 10 false CANL 1.458,1.5 1.885,1.688 0.427,0.188 10 false CANH 3.042,1.521 3.375,1.698 0.333,0.177 10 false GND 5.979,1.479 6.271,1.656 0.292,0.177 10 false BAT

a.

Disconnect the F36 yaw rate sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F36-3 (CANH) - F36-2 (CANL) R - W Ignition switch off 54 to 69 Ω
F36-3 (CANH) - F36-1 (GND) R - W-B Ignition switch off 200 Ω or higher
F36-2 (CANL) - F36-1 (GND) W - W-B Ignition switch off 200 Ω or higher
F36-3 (CANH) - F13-16 (BAT) R - GR Ignition switch off 6 kΩ or higher
F36-2 (CANL) - F13-16 (BAT) W - GR Ignition switch off 6 kΩ or higher



CHECK POWER STEERING ECU ASSEMBLY


U180967E02
2.125,1.052 2.344,0.458 2.344,0.458 2.469,0.458 true 2.292,1.063 2.646,0.688 2.646,0.688 2.75,0.688 true 5.771,1.281 5.979,1.406 5.979,1.406 6.083,1.406 true 1.781,0.469 1.865,0.469 1.865,0.469 1.99,1.063 true 0.427,0.938 0.698,1.115 0.271,0.177 10 false F41 2.802,0.615 3.25,0.792 0.448,0.177 10 false CANH 2.5,0.375 2.906,0.542 0.406,0.167 10 false CANL 1.396,0.385 1.74,0.573 0.344,0.188 10 false GND 6.167,1.313 6.531,1.5 0.365,0.188 10 false BAT 4.01,1 4.302,1.167 0.292,0.167 10 false F13

a.

Disconnect the F41 power steering ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F41-1 (CANH) - F41-2 (CANL) L - W Ignition switch off 54 to 69 Ω
F41-1 (CANH) - F41-3 (GND) L - W-B Ignition switch off 200 Ω or higher
F41-2 (CANL) - F41-3 (GND) W - W-B Ignition switch off 200 Ω or higher
F41-1 (CANH) - F13-16 (BAT) L - GR Ignition switch off 6 kΩ or higher
F41-2 (CANL) - F13-16 (BAT) W - GR Ignition switch off 6 kΩ or higher



CHECK FOUR WHEEL DRIVE CONTROL ECU (for 4WD)


U150051E03
0.906,0.813 0.844,0.354 0.844,0.354 0.76,0.354 true 0.802,0.823 0.667,0.531 0.667,0.531 0.583,0.531 true 2.49,0.802 2.365,0.438 2.365,0.438 2.281,0.438 true 5.781,1.125 5.906,1.365 5.906,1.365 6,1.365 true 1.917,0.375 2.25,0.563 0.333,0.188 10 false GND 2.677,0.344 2.969,0.521 0.292,0.177 10 false F46 0.344,0.25 0.76,0.438 0.417,0.188 10 false CANH 0.177,0.49 0.573,0.677 0.396,0.188 10 false CANL 1.417,0.333 1.708,0.51 0.292,0.177 10 false F47 4.052,0.844 4.333,1.021 0.281,0.177 10 false F13 6.073,1.302 6.365,1.49 0.292,0.188 10 false BAT

a.

Disconnect the F46 and F47 four wheel drive control ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F47-19 (CANH) - F47-20 (CANL) G - W Ignition switch off 54 to 69 Ω
F47-19 (CANH) - F46-4 (GND) G - W-B Ignition switch off 200 Ω or higher
F47-20 (CANL) - F46-4 (GND) W - W-B Ignition switch off 200 Ω or higher
F47-19 (CANH) - F13-16 (BAT) G - GR Ignition switch off 6 kΩ or higher
F47-20 (CANL) - F13-16 (BAT) W - GR Ignition switch off 6 kΩ or higher



CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY (w/ Radio and Display Receiver Assembly)


U181078E02
5.792,0.521 5.708,0.521 5.708,0.521 5.281,0.958 true 4.74,0.521 4.823,0.521 4.823,0.521 5.146,0.969 true 0.281,0.531 0.365,0.531 0.365,0.531 0.583,0.906 true 0.656,1.542 0.75,1.542 0.75,1.542 1.01,1.135 true 5.302,0.302 5.594,0.458 0.292,0.156 10 false G29 0.854,0.354 1.146,0.51 0.292,0.156 10 false G36 5.885,0.458 6.344,0.667 0.458,0.208 10 false CANH 4.302,0.427 4.698,0.635 0.396,0.208 10 false CANL 0.104,0.458 0.25,0.667 0.146,0.208 10 false B 0.292,1.479 0.656,1.688 0.365,0.208 10 false GND

a.

Disconnect the G6 and G29 radio and display receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G29-9 (CANH) - G29-10 (CANL) P - W Ignition switch off 54 to 69 Ω
G29-9 (CANH) - G36-7 (GND) P - BR Ignition switch off 200 Ω or higher
G29-10 (CANL) - G36-7 (GND) W - BR Ignition switch off 200 Ω or higher
G29-9 (CANH) - G36-4 (B) P - SB Ignition switch off 6 kΩ or higher
G29-10 (CANL) - G36-4 (B) W - SB Ignition switch off 6 kΩ or higher



CHECK FRONT POWER SEAT SWITCH LH (w/ Seat Position Memory)


U149700E03
4.948,0.833 4.865,0.833 4.865,0.833 4.448,1.208 true 4.938,1.521 4.854,1.521 4.854,1.521 4.365,1.219 true 3.646,0.531 3.583,0.531 3.583,0.531 3.552,0.896 true 2.344,1.604 2.427,1.604 2.427,1.604 3.521,1.135 true 4.125,0.323 4.385,0.479 0.26,0.156 10 false b19 3.125,0.323 3.385,0.479 0.26,0.156 10 false b18 5.01,0.771 5.469,0.979 0.458,0.208 10 false CANN 5.021,1.458 5.479,1.667 0.458,0.208 10 false CANP 2.167,1.5 2.313,1.708 0.146,0.208 10 false B 3.667,0.448 4.031,0.615 0.365,0.167 10 false GND

a.

Disconnect the b18 and b19 front power seat switch LH connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
b19-8 (CANP) - b19-7 (CANN) L - W Ignition switch off 54 to 69 Ω
b19-8 (CANP) - b18-2 (GND) L - W-B Ignition switch off 200 Ω or higher
b19-7 (CANN) - b18-2 (GND) W - W-B Ignition switch off 200 Ω or higher
b19-8 (CANP) - b18-7 (B) L - W Ignition switch off 6 kΩ or higher
b19-7 (CANN) - b18-7 (B) W - W Ignition switch off 6 kΩ or higher