Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM1440E _57 Power Source / Network _056154 NETWORKING _0274053 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Steering Angle Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Steering Angle Sensor Communication Stop Mode Either condition is met:
·

"Steering Angle Sensor" is not displayed on the "Bus Check" screen.


·

"Steering Angle Sensor Communication Stop Mode" in "DTC Combination Table" applies.


·

Power source or inside spiral cable sub-assembly (steering angle sensor)

·

Spiral cable sub-assembly (steering angle sensor) branch wire or connector

·

Spiral cable sub-assembly (steering angle sensor)



WIRING DIAGRAM

C198942E26
5.292,2.695 5.686,2.871 0.395,0.176 10 F19 5.292,2.855 7.097,3.218 1.805,0.364 10 Spiral Cable Sub-assembly (Steering Angle Sensor) 0.619,1.381 1.019,1.557 0.400,0.176 10 F59 0.619,1.54 2.274,1.717 1.655,0.176 10 No. 2 Junction Connector 5.812,0.528 6.278,0.704 0.466,0.176 10 CANH 1.941,0.43 2.049,0.584 0.109,0.154 10 7 5.608,0.446 5.740,0.600 0.132,0.154 10 4 5.608,0.886 5.740,1.040 0.132,0.154 10 3 5.608,1.329 5.740,1.483 0.132,0.154 10 6 5.608,1.766 5.740,1.919 0.132,0.154 10 5 5.608,2.205 5.740,2.359 0.132,0.154 10 2 4.623,1.292 5.105,1.446 0.481,0.154 10 ECU-B 2.889,1.41 3.691,1.582 0.802,0.172 10 from Battery 2.289,1.848 3.686,2.020 1.397,0.172 10 from IG1 NO. 1 Relay 4.4,1.72 5.309,1.874 0.910,0.154 10 ECU-IG NO. 1 1.941,0.884 2.135,1.037 0.194,0.153 10 18 5.812,0.966 6.278,1.142 0.466,0.176 10 CANL 5.812,1.416 6.278,1.592 0.466,0.176 10 BAT 5.812,1.866 6.278,2.042 0.466,0.176 10 IG 5.812,2.309 6.278,2.485 0.466,0.176 10 ESS

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

2.CHECK FOR OPEN IN CAN BUS WIRE (SPIRAL CABLE BRANCH WIRE)
2.CHECK FOR OPEN IN CAN BUS WIRE (SPIRAL CABLE BRANCH WIRE)
a.
U180817E02
2.042,1.531 1.729,1.052 1.729,1.052 1.656,1.052 true 2.146,1.521 2.396,1.26 2.396,1.26 2.552,1.26 true 1.198,0.99 1.625,1.188 0.427,0.198 10 false CANH 1.219,1.396 1.542,1.594 0.323,0.198 10 false F19 0.094,0.073 0.323,0.26 0.229,0.188 10 false *a 2.625,1.188 3.042,1.385 0.417,0.198 10 false CANL

Disconnect the F19 spiral cable sub-assembly (steering angle sensor) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F19-4 (CANH) - F19-3 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Spiral Cable Sub-assembly [Steering Angle Sensor])



OK

3.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE SPIRAL CABLE BRANCH WIRE OR CONNECTOR (CANH, CANL)

3.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - BATTERY AND BODY GROUND)
a.
U180818E02
1.833,1.552 1.521,1.135 1.521,1.135 1.438,1.135 true 2.24,1.552 2.458,1.271 2.458,1.271 2.552,1.271 true 1.938,1.542 1.698,0.906 1.698,0.906 1.615,0.906 true 1.125,1.063 1.417,1.26 0.292,0.198 10 false BAT 1.156,1.448 1.458,1.646 0.302,0.198 10 false F19 1.396,0.823 1.573,1.021 0.177,0.198 10 false IG 0.083,0.042 0.323,0.25 0.24,0.208 10 false *a 2.646,1.198 3.063,1.396 0.417,0.198 10 false ESS

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F19-2 (ESS) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F19-6 (BAT) - Body ground Always 11 to 14 V
F19-5 (IG) - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Rear view of wire harness connector
(to Spiral Cable Sub-assembly [Steering Angle Sensor])


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR