Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM1440E _57 Power Source / Network _056154 NETWORKING _0274053 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Yaw Rate Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Yaw Rate Sensor Communication Stop Mode Either condition is met:
·

"Yaw Rate / Deceleration Sensor" is not displayed on the "Bus Check" screen.

·

"Yaw Rate Sensor Communication Stop Mode" in "DTC Combination Table" applies.


·

Power source or inside yaw rate sensor assembly

·

Yaw rate sensor assembly branch wire or connector

·

Yaw rate sensor assembly



WIRING DIAGRAM

C361664E02
1.927,0.469 2.083,0.646 0.156,0.177 10 false 7 1.906,0.896 2.104,1.083 0.198,0.188 10 false 18 0.49,1.417 0.781,1.594 0.292,0.177 10 false F60 0.5,1.583 2.094,1.781 1.594,0.198 10 false No. 3 Junction Connector 5.542,0.458 5.688,0.635 0.146,0.177 10 false 3 5.542,0.906 5.677,1.073 0.135,0.167 10 false 2 5.563,1.76 5.688,1.948 0.125,0.188 10 false 4 5.563,2.219 5.708,2.385 0.146,0.167 10 false 1 5.802,0.604 6.26,0.792 0.458,0.188 10 false CANH 5.823,1.01 6.229,1.188 0.406,0.177 10 false CANL 5.802,1.885 6.031,2.063 0.229,0.177 10 false IG 5.802,2.333 6.125,2.521 0.323,0.188 10 false GND 4.344,1.74 5.271,1.927 0.927,0.188 10 false ECU-IG NO. 1 2.344,1.885 3.688,2.115 1.344,0.229 10 false from IG1 NO. 1 Relay 5.49,2.729 5.802,2.927 0.313,0.198 10 false F36 5.469,2.927 6.625,3.333 1.156,0.406 10 false Yaw Rate Sensor Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

2.CHECK FOR OPEN IN CAN BUS WIRE (YAW RATE SENSOR BRANCH WIRE)
2.CHECK FOR OPEN IN CAN BUS WIRE (YAW RATE SENSOR BRANCH WIRE)
a.
U180829E02
0.906,0.979 1,0.979 1,0.979 1.427,1.438 true 1.177,0.563 1.292,0.563 1.292,0.563 1.573,1.448 true 0.052,0.031 0.229,0.208 0.177,0.177 10 false *a 0.458,0.927 0.865,1.104 0.406,0.177 10 false CANL 0.438,1.448 0.74,1.625 0.302,0.177 10 false F36 0.719,0.49 1.146,0.667 0.427,0.177 10 false CANH

Disconnect the F36 yaw rate sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connector Switch Condition Specified Condition
F36-3 (CANH) - F36-2 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Yaw Rate Sensor Assembly)



OK

3.CHECK HARNESS AND CONNECTOR (YAW RATE SENSOR - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE YAW RATE SENSOR BRANCH WIRE OR CONNECTOR (CANH, CANL)

3.CHECK HARNESS AND CONNECTOR (YAW RATE SENSOR - BATTERY AND BODY GROUND)
a.
U180830E02
0.823,1.021 0.917,1.021 0.917,1.021 1.271,1.458 true 2.406,0.729 2.271,0.729 2.271,0.729 1.74,1.438 true 0.052,0.083 0.229,0.26 0.177,0.177 10 false *a 0.438,0.948 0.771,1.125 0.333,0.177 10 false GND 0.406,1.427 0.708,1.604 0.302,0.177 10 false F36 2.448,0.635 2.615,0.813 0.167,0.177 10 false IG

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F36-1 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F36-4 (IG) - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Yaw Rate Sensor Assembly)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR