BUS CHECK (COMMUNICATION MALFUNCTION ECU)
Only CAN communication system DTCs for each ECU can be output to the intelligent tester.
Select "Bus Check" from the "System Select" screen on the intelligent tester.
Select "Communication Malfunction DTC" from the "Bus Check" screen, and then select "Enter".
Select the system of the DTC to be checked and select "Details".
CAN communication system DTCs are output.
BUS CHECK (COMMUNICATION BUS CHECK)
The ECUs and sensors that are properly connected to the CAN communication system can be displayed using the intelligent tester.
Select "Communication Bus Check" from the "Bus Check" screen.
The screen displays the ECUs and sensors that are properly connected to the CAN communication system.
If any properly connected ECUs or sensors are not displayed, there is a communication stop in the system (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>PROBLEM SYMPTOMS TABLE).
The default item displayed in the combo box is "ALL". When checking the ECUs (sensors) connected to each bus, pull down the combo box and select the bus to be checked from the drop-down list. The drop-down list displays "ALL", "V Bus" and the names of the remaining buses.
| Combo Box | Display Content |
|---|---|
| ALL | All ECUs (sensors) connected to the CAN bus |
| V Bus | ECUs (sensors) connected to the V Bus |
| Bus Name | ECUs (sensors) connected to the selected bus |
The connection status (shown below) is indicated by the background color displayed behind the system name.
| Background Color | Connection Status |
|---|---|
| White | Detected normally |
| Yellow | Could not be detected in the past, but is currently detected |
| Red | Detected in the past, but cannot be detected now |
| Not displayed | Has never been detected |
| Background Color | Connection Status |
|---|---|
| White | Detected normally |
| Yellow | Could not be detected in the past, but is currently detected |
| Red | Detected in the past, but cannot be detected now |
| Not displayed | Has never been detected |
| Background Color | Connection Status |
|---|---|
| White | Detected normally |
| Yellow | Could not be detected in the past, but is currently detected |
| Red | Detected in the past, but cannot be detected now |
| Red | Has never been detected but has connection history |
| Not displayed | Has never been detected and has no connection history |
"There is no system connected the communication bus." is displayed if there are no ECUs or sensors connected to the CAN bus.
CHECK INSTALLED SYSTEMS (ECUS AND SENSORS) THAT USE CAN COMMUNICATION
Systems (ECUs and sensors) that use CAN communication vary depending on the optional settings of the vehicle. Check which systems (ECUs and sensors) are installed on the vehicle.
| ECU/Sensor Name | Tester Display | Installed on |
|---|---|---|
| ECM | ECM (Engine) | All vehicles |
| Skid control ECU (master cylinder solenoid) | Skid Control (ABS/VSC/TRAC) | All vehicles |
| Yaw rate sensor assembly | Yaw Rate Sensor | All vehicles |
| Steering angle sensor (spiral cable sub-assembly) | Spiral cable (Steering Angle Sensor) | All vehicles |
| Power steering ECU assembly | PPS | All vehicles |
| Air conditioning amplifier assembly | Air Conditioning Amplifier | All vehicles |
| Airbag sensor assembly | Airbag | All vehicles |
| Main body ECU (multiplex network body ECU) | Main Body | All vehicles |
| Combination meter assembly | Combination Meter | All vehicles |
| Four wheel drive control ECU | Four Wheel Drive Control | for 4WD |
| Radio and display receiver assembly | Display and Navigation (AVN1) | w/ Radio and Display Receiver Assembly |
| Front power seat switch LH | D-Seat | w/ Seat Position Memory |
DTC TABLE BY ECU
In the CAN communication system, CAN communication system DTCs output from an ECU can be output by using the intelligent tester.
If CAN communication system DTCs are output, the trouble cannot be determined solely from the DTCs. Perform troubleshooting according to "How to Proceed with Troubleshooting".
MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
DTC communication uses the CAN communication system.
| DTC Code | Detection Item |
|---|---|
| U0100 | Lost Communication With ECM/PCM "A" |
| U0101 | Lost Communication with TCM |
| U0151 | Lost Communication with Restraints Control Module |
| U0155 | Lost Communication with Instrument Panel Cluster (IPC) Control Module |
| U0164 | Lost Communication With HVAC Control Module |
| U0208 | Lost Communication with "Seat Control Module A" |
| U1002 | Lost Communication with Gateway Module |
SKID CONTROL ECU (MASTER CYLINDER SOLENOID)
DTC communication uses the CAN communication system.
| DTC Code | Detection Item |
|---|---|
| U0073 | Control Module Communication Bus OFF |
| U0100 | Lost Communication with ECM / PCM "A" |
| U0114 | Lost Communication with 4WD Control Module |
| U0123 | Lost Communication with Yaw Rate Sensor Module |
| U0124 | Lost Communication with Lateral Acceleration Sensor Module |
| U0126 | Lost Communication with Steering Angle Sensor Module |
POWER STEERING ECU ASSEMBLY
DTC communication uses the CAN communication system.
| DTC Code | Detection Item |
|---|---|
| U0100 | Lost Communication with ECM/PCM "A" |
| U0126 | Lost Communication with Steering Angle Sensor Module |
| U0129 | Lost Communication with Brake System Control Module |
ECM
The ECM is connected to the CAN communication system but CAN communication DTCs are not stored.
COMBINATION METER ASSEMBLY
DTC communication uses the CAN communication system.
| DTC Code | Detection Item |
|---|---|
| U0100 | Lost Communication with ECM/PCM "A" |
| U0129 | Lost Communication with Brake System Control Module |
| U0131 | Lost Communication with Power Steering Control Module |
| U0151 | Lost Communication with Restraints Control Module |
AIRBAG SENSOR ASSEMBLY
The airbag sensor assembly is connected to the CAN communication system but CAN communication DTCs are not stored.
RADIO AND DISPLAY RECEIVER ASSEMBLY
For vehicles with a radio and display receiver assembly.
DTC communication uses the CAN communication system.
| DTC Code | Detection Item |
|---|---|
| U0073 | Sending Malfunction (Navigation to APGS) |
| U0140 | Lost Communication with Body Control Module |
AIR CONDITIONING AMPLIFIER ASSEMBLY
DTC communication uses the CAN communication system.
| DTC Code | Detection Item |
|---|---|
| U0100 | Lost Communication with ECM/PCM "A" |
| U0142 | Lost Communication with Body Control Module "B" |
| U0155 | Lost Communication with Instrument Panel Cluster (IPC) Control Module |
YAW RATE SENSOR ASSEMBLY
The yaw rate sensor assembly is connected to the CAN communication system but CAN communication DTCs are not stored.
STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY)
The steering angle sensor (spiral cable sub-assembly) is connected to the CAN communication system but CAN communication DTCs are not stored.
FOUR WHEEL DRIVE CONTROL ECU
For vehicles with four wheel drive.
The four wheel drive control ECU is connected to the CAN communication system but CAN communication DTCs are not stored.
FRONT POWER SEAT SWITCH LH
For vehicles with seat position memory.
The front power seat switch LH is connected to the CAN communication system, but CAN communication DTCs are not output.
DTC COMBINATION TABLE
○: Stored.
X: When one side of the branch wire is open, storage may occur.
*1: Only stored when communication recovery occurs. During a communication stop it, cannot be stored.
*2: Only output while a malfunction is present and the ignition switch is ON.
| Output from | Output DTC | Detection Item | Detected Communication Stop Mode | ||||
|---|---|---|---|---|---|---|---|
| V1 Bus | |||||||
| Main Body ECU Communication Stop Mode | ECM Communication Stop Mode | Brake Actuator (Skid Control ECU) Communication Stop Mode | Yaw Rate Sensor Communication Stop Mode | Steering Angle Sensor Communication Stop Mode | |||
| Main body ECU (multiplex network body ECU) | U0100 | Lost Communication With ECM/PCM "A" | ○*1 | ○ | X | X | X |
| U0101 | Lost Communication with TCM | ○*1 | ○ | X | X | X | |
| U0151 | Lost Communication with Restraints Control Module | ○*1 | X | X | X | X | |
| U0155 | Lost Communication with Instrument Panel Cluster (IPC) Control Module | ○*1 | X | X | X | X | |
| U0164 | Lost Communication With HVAC Control Module | ○*1 | X | X | X | X | |
| U0208 | Lost Communication with "Seat Control Module A" | - | - | - | - | - | |
| U1002 | Lost Communication with Gateway Module | - | - | - | - | - | |
| Skid control ECU (master cylinder solenoid) | U0073*2 | Control Module Communication Bus Off | X | X | ○*1 | X | X |
| U0100*2 | Lost Communication with ECM / PCM "A" | X | ○ | ○*1 | X | X | |
| U0114*2 | Lost Communication with 4WD Control Module | X | X | ○*1 | X | X | |
| U0123*2 | Lost Communication with Yaw Rate Sensor Module | X | X | ○*1 | ○ | X | |
| U0124*2 | Lost Communication with Lateral Acceleration Sensor Module | X | X | ○*1 | ○ | X | |
| U0126*2 | Lost Communication with Steering Angle Sensor Module | X | X | ○*1 | X | ○ | |
| Power steering ECU assembly | U0100 | Lost Communication with ECM/PCM "A" | X | ○ | X | X | X |
| U0126 | Lost Communication with Steering Angle Sensor Module | X | X | X | X | ○ | |
| U0129 | Lost Communication with Brake System Control Module | X | X | ○ | X | X | |
| Combination meter assembly | U0100 | Lost Communication with ECM/PCM "A" | X | ○ | X | X | X |
| U0129 | Lost Communication with Brake System Control Module | X | X | ○ | X | X | |
| U0131 | Lost Communication with Power Steering Control Module | X | X | X | X | X | |
| U0151 | Lost Communication with Restraints Control Module | X | X | X | X | X | |
| Radio and display receiver assembly | U0073 | Sending Malfunction (Navigation to APGS) | X | X | X | X | X |
| U0140 | Lost Communication with Body Control Module | ○ | X | X | X | X | |
| Air conditioning amplifier assembly | U0100 | Lost Communication With ECM/PCM "A" | X | ○ | X | X | X |
| U0142 | Lost Communication With Body Control Module "B" | ○ | X | X | X | X | |
| U0155 | Lost Communication With Instrument Panel Cluster (IPC) Control Module | X | X | X | X | X | |
| Output from | Output DTC | Detection Item | Detected Communication Stop Mode | |||||
|---|---|---|---|---|---|---|---|---|
| V1 Bus | ||||||||
| Power Steering ECU Communication Stop Mode | Center Airbag Sensor Communication Stop Mode | Combination Meter ECU Communication Stop Mode | Audio Receiver Assembly Communication Stop Mode | 4WD Control ECU Communication Stop Mode | Air Conditioning Amplifier Communication Stop Mode | |||
| Main body ECU (multiplex network body ECU) | U0100 | Lost Communication With ECM/PCM "A" | X | X | X | X | X | X |
| U0101 | Lost Communication with TCM | X | X | X | X | X | X | |
| U0151 | Lost Communication with Restraints Control Module | X | ○ | X | X | X | X | |
| U0155 | Lost Communication with Instrument Panel Cluster (IPC) Control Module | X | X | ○ | X | X | X | |
| U0164 | Lost Communication With HVAC Control Module | X | X | X | X | X | ○ | |
| U0208 | Lost Communication with "Seat Control Module A" | - | - | - | - | - | - | |
| U1002 | Lost Communication with Gateway Module | - | - | - | - | - | - | |
| Skid control ECU (master cylinder solenoid) | U0073*2 | Control Module Communication Bus Off | X | X | X | X | X | X |
| U0100*2 | Lost Communication with ECM / PCM "A" | X | X | X | X | X | X | |
| U01114*2 | Lost Communication with 4WD Control Module | X | X | X | X | ○ | X | |
| U0123*2 | Lost Communication with Yaw Rate Sensor Module | X | X | X | X | X | X | |
| U0124*2 | Lost Communication with Lateral Acceleration Sensor Module | X | X | X | X | X | X | |
| U0126*2 | Lost Communication with Steering Angle Sensor Module | X | X | X | X | X | X | |
| Power steering ECU assembly | U0100 | Lost Communication with ECM/PCM "A" | ○*1 | X | X | X | X | X |
| U0126 | Lost Communication with Steering Angle Sensor Module | ○*1 | X | X | X | X | X | |
| U0129 | Lost Communication with Brake System Control Module | ○*1 | X | X | X | X | X | |
| Combination meter assembly | U0100 | Lost Communication with ECM/PCM "A" | X | X | ○*1 | X | X | X |
| U0129 | Lost Communication with Brake System Control Module | X | X | ○*1 | X | X | X | |
| U0131 | Lost Communication with Power Steering Control Module | ○ | X | ○*1 | X | X | X | |
| U0151 | Lost Communication with Restraints Control Module | X | ○ | ○*1 | X | X | X | |
| Radio and display receiver assembly | U0073 | Sending Malfunction (Navigation to APGS) | X | X | X | ○*1 | X | X |
| U0140 | Lost Communication with Body Control Module | X | X | X | ○*1 | X | X | |
| Air conditioning amplifier assembly | U0100 | Lost Communication With ECM/PCM "A" | X | X | X | X | X | X |
| U0142 | Lost Communication With Body Control Module "B" | X | X | X | X | X | X | |
| U0155 | Lost Communication With Instrument Panel Cluster (IPC) Control Module | X | X | ○ | X | X | X | |
| Output from | Output DTC | Detection Item | Detected Communication Stop Mode | |
|---|---|---|---|---|
| MS Bus | ||||
| Front Power Seat ECU and Switch LH Communication Stop Mode | Main Body ECU Communication Stop Mode | |||
| Main body ECU (multiplex network body ECU) | U0100 | Lost Communication With ECM/PCM "A" | - | - |
| U0101 | Lost Communication with TCM | - | - | |
| U0151 | Lost Communication with Restraints Control Module | - | - | |
| U0155 | Lost Communication with Instrument Panel Cluster (IPC) Control Module | - | - | |
| U0164 | Lost Communication with HVAC Control Module | - | - | |
| U0208 | Lost Communication with "Seat Control Module A" | ○ | ○*1 | |
| U1002 | Lost Communication with Gateway Module | ○ | ○*1 | |
| Skid control ECU (master cylinder solenoid) | U0073*4 | Control Module Communication Bus Off | - | - |
| U0100*4 | Lost Communication with ECM/PCM "A" | - | - | |
| U0114*4 | Lost Communication with 4WD Control Module | - | - | |
| U0123*4 | Lost Communication with Yaw Rate Sensor Module | - | - | |
| U0124*4 | Lost Communication with Lateral Acceleration Sensor Module | - | - | |
| U0126*4 | Lost Communication with Steering Angle Sensor Module | - | - | |
| Power steering ECU assembly | U0100 | Lost Communication with ECM/PCM "A" | - | - |
| U0126 | Lost Communication with Steering Angle Sensor Module | - | - | |
| U0129 | Lost Communication with Brake System Control Module | - | - | |
| Combination meter assembly | U0100 | Lost Communication with ECM/PCM "A" | - | - |
| U0129 | Lost Communication with Brake System Control Module | - | - | |
| U0131 | Lost Communication with Power Steering Control Module | - | - | |
| U0151 | Lost Communication with Restraints Control Module | - | - | |
| Radio and display receiver assembly | U0073 | Sending Malfunction (Navigation to APGS) | - | - |
| U0140 | Lost Communication with Body Control Module | - | - | |
| Air conditioning amplifier assembly | U0100 | Lost Communication With ECM/PCM "A" | - | - |
| U0142 | Lost Communication With Body Control Module "B" | - | - | |
| U0155 | Lost Communication With Instrument Panel Cluster (IPC) Control Module | - | - | |