Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM1440E _57 Power Source / Network _056154 NETWORKING _0274053 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Power Steering ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Power Steering ECU Communication Stop Mode Either condition is met:
·

"PPS" is not displayed on the "Bus Check" screen.

·

"Power Steering ECU Communication Stop Mode" in "DTC Combination Table" applies.


·

Power source or inside power steering ECU assembly

·

Power steering ECU assembly branch wire or connector

·

Power steering ECU assembly



WIRING DIAGRAM

C361664E01
1.927,0.469 2.083,0.646 0.156,0.177 10 false 5 1.917,0.896 2.115,1.083 0.198,0.188 10 false 16 0.49,1.417 0.781,1.594 0.292,0.177 10 false F60 0.5,1.583 2.094,1.781 1.594,0.198 10 false No. 3 Junction Connector 5.542,0.458 5.688,0.635 0.146,0.177 10 false 1 5.542,0.906 5.677,1.073 0.135,0.167 10 false 2 5.563,1.76 5.688,1.948 0.125,0.188 10 false 5 5.563,2.219 5.708,2.385 0.146,0.167 10 false 3 5.802,0.594 6.26,0.781 0.458,0.188 10 false CANH 5.823,1.01 6.229,1.188 0.406,0.177 10 false CANL 5.802,1.885 6.031,2.063 0.229,0.177 10 false IG 5.802,2.333 6.125,2.521 0.323,0.188 10 false GND 4.344,1.74 5.271,1.927 0.927,0.188 10 false ECU-IG NO. 1 2.344,1.885 3.688,2.115 1.344,0.229 10 false from IG1 NO. 1 Relay 5.156,2.833 5.469,3.031 0.313,0.198 10 false F41 5.146,3.01 7.104,3.219 1.958,0.208 10 false Power Steering ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

2.CHECK FOR OPEN IN CAN BUS WIRE (POWER STEERING ECU BRANCH WIRE)
2.CHECK FOR OPEN IN CAN BUS WIRE (POWER STEERING ECU BRANCH WIRE)
a.
U180836E02
1.917,1.51 2.135,1.052 2.135,1.052 2.229,1.052 true 2.375,1.24 2.302,1.24 2.302,1.24 2.031,1.51 true 0.063,0.052 0.281,0.25 0.219,0.198 10 false *a 2.438,1.177 2.865,1.344 0.427,0.167 10 false CANH 2.281,0.969 2.698,1.135 0.417,0.167 10 false CANL 0.677,1.333 1,1.5 0.323,0.167 10 false F41

Disconnect the F41 power steering ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F41-1 (CANH) - F41-2 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Power Steering ECU Assembly)



OK

3.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE POWER STEERING ECU BRANCH WIRE OR CONNECTOR (CANH, CANL)

3.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU - BATTERY AND BODY GROUND)
a.
U180837E02
1.823,1.521 2.146,1.031 2.146,1.031 2.24,1.031 true 1.323,1.927 1.406,1.927 1.406,1.927 1.625,1.563 true 0.073,0.052 0.302,0.24 0.229,0.188 10 false *a 1.094,1.854 1.26,2.021 0.167,0.167 10 false IG 2.302,0.948 2.667,1.115 0.365,0.167 10 false GND 0.708,1.365 1.031,1.531 0.323,0.167 10 false F41

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F41-3 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F41-5 (IG) - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Rear view of wire harness connector
(to Power Steering ECU Assembly)


OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR