Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM1440E _57 Power Source / Network _056154 NETWORKING _0274053 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Air Conditioning Amplifier Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Air Conditioning Amplifier Communication Stop Mode Either condition is met:
·

"Air Conditioner" is not displayed on the "Bus Check" screen.


·

"Air Conditioning Amplifier Communication Stop Mode" in "DTC Combination Table" applies.


·

Power source or inside air conditioning amplifier assembly

·

Air conditioning amplifier assembly branch wire or connector

·

Air conditioning amplifier assembly



WIRING DIAGRAM

C198937E61
5.385,2.74 5.813,2.917 0.427,0.177 10 false F42 5.385,2.896 7.01,3.26 1.625,0.365 10 false Air Conditioning Amplifier Assembly 0.615,1.385 1.01,1.563 0.396,0.177 10 false F60 0.615,1.542 2.344,1.719 1.729,0.177 10 false No. 3 Junction Connector 5.823,0.563 6.292,0.74 0.469,0.177 10 false CANH 1.938,0.427 2.104,0.583 0.167,0.156 10 false 8 5.531,0.427 5.729,0.583 0.198,0.156 10 false 11 5.531,0.885 5.729,1.042 0.198,0.156 10 false 12 5.531,1.323 5.729,1.479 0.198,0.156 10 false 21 4.948,1.573 5.24,1.729 0.292,0.156 10 false A/C 3.354,1.448 4.156,1.625 0.802,0.177 10 false from Battery 2.792,1.896 4.167,2.073 1.375,0.177 10 false from IG1 NO. 1 Relay 4.615,2.01 5.531,2.167 0.917,0.156 10 false ECU-IG NO. 2 5.594,1.771 5.708,1.927 0.115,0.156 10 false 1 5.531,2.208 5.729,2.365 0.198,0.156 10 false 14 1.938,0.885 2.135,1.042 0.198,0.156 10 false 19 5.813,1 6.281,1.177 0.469,0.177 10 false CANL 5.813,1.448 6,1.635 0.188,0.188 10 false B 5.813,1.906 6.104,2.104 0.292,0.198 10 false IG+ 5.813,2.344 6.167,2.531 0.354,0.188 10 false GND

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

2.CHECK FOR OPEN IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER BRANCH WIRE)
2.CHECK FOR OPEN IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER BRANCH WIRE)
a.
U180889E02
2.125,1.042 1.927,0.188 1.927,0.188 1.74,0.188 false 1.99,1.052 1.354,0.292 1.354,0.292 1.156,0.292 true 0.083,0.063 0.26,0.271 0.177,0.208 10 false *a 0.49,0.969 0.802,1.146 0.313,0.177 10 false F42 1.313,0.115 1.75,0.281 0.438,0.167 10 false CANH 0.771,0.208 1.177,0.385 0.406,0.177 10 false CANL

Disconnect the F42 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F42-11 (CANH) - F42-12 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)



OK

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE AIR CONDITIONING AMPLIFIER BRANCH WIRE OR CONNECTOR (CANH, CANL)

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BATTERY AND BODY GROUND)
a.
U180890E02
3.188,1.052 2.917,0.177 2.917,0.177 2.792,0.177 true 1.792,1.063 1.396,0.385 1.396,0.385 1.26,0.385 true 3.219,1.271 3.031,1.875 3.031,1.875 2.906,1.875 true 0.073,0.094 0.25,0.302 0.177,0.208 10 false *a 0.5,1 0.813,1.177 0.313,0.177 10 false F42 2.5,0.094 2.781,0.26 0.281,0.167 10 false IG+ 2.75,1.792 2.896,1.969 0.146,0.177 10 false B 0.885,0.292 1.24,0.458 0.354,0.167 10 false GND

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F42-14 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F42-21 (B) - Body ground Always 11 to 14 V
F42-1 (IG+) - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)


OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR