Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2013.08
RM1440E _57 Power Source / Network _056154 NETWORKING _0274053 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Audio Receiver Assembly Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Audio Receiver Assembly Communication Stop Mode Either condition is met:
·

"Display and Navigation (AVN1)" is not displayed on the "Bus Check" screen.

·

"Audio Receiver Assembly Communication Stop Mode" in "DTC Combination Table" applies.


·

Power source or inside radio and display receiver assembly

·

Radio and display receiver assembly branch wire or connector

·

Radio and display receiver assembly



HINT:

For vehicles with a radio and display receiver assembly only.


WIRING DIAGRAM

C289983E06
5.604,2.792 6.917,3.188 1.313,0.396 10 false Radio and Display Receiver Assembly 0.646,1.469 0.948,1.646 0.302,0.177 10 false G14 0.646,1.646 2.229,1.833 1.583,0.188 10 false No. 4 Junction Connector 5.76,0.583 6.188,0.76 0.427,0.177 10 false CANH 1.896,0.49 2,0.646 0.104,0.156 10 false 6 5.49,0.365 5.625,0.521 0.135,0.156 10 false 9 5.396,0.594 5.698,0.75 0.302,0.156 10 false G29 5.458,0.823 5.646,0.979 0.188,0.156 10 false 10 5.396,1.469 5.698,1.625 0.302,0.156 10 false G29 5.49,1.698 5.625,1.854 0.135,0.156 10 false 4 5.417,2.333 5.719,2.49 0.302,0.156 10 false G36 5.5,2.125 5.635,2.281 0.135,0.156 10 false 7 5.427,1.906 5.729,2.063 0.302,0.156 10 false G36 2.854,1.906 3.667,2.083 0.813,0.177 10 false from Battery 2.313,1.448 3.677,1.625 1.365,0.177 10 false from IG1 No. 1 Relay 4.458,2.031 5.188,2.188 0.729,0.156 10 false RAD NO. 1 4.365,1.583 5.281,1.74 0.917,0.156 10 false ECU-IG NO. 2 1.896,0.927 2.094,1.083 0.198,0.156 10 false 17 5.76,1.021 6.156,1.198 0.396,0.177 10 false CANL 5.771,1.896 5.938,2.083 0.167,0.188 10 false B 5.49,1.271 5.625,1.427 0.135,0.156 10 false 1 5.406,1.021 5.708,1.177 0.302,0.156 10 false G29 5.76,1.458 5.958,1.646 0.198,0.188 10 false IG 5.771,2.333 6.135,2.51 0.365,0.177 10 false GND

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

2.CHECK FOR OPEN IN CAN BUS WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY BRANCH WIRE)
2.CHECK FOR OPEN IN CAN BUS WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY BRANCH WIRE)
a.
U180983E02
1.76,1.885 1.271,0.792 true 1.906,1.896 2.396,0.802 true 0.125,0.083 0.333,0.271 0.208,0.188 10 false *a 2.448,0.708 2.854,0.885 0.406,0.177 10 false CANL 0.844,0.698 1.25,0.875 0.406,0.177 10 false CANH 0.229,1.896 0.51,2.063 0.281,0.167 10 false G29

Disconnect the G29 radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G29-9 (CANH) - G29-10 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)



OK

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY BRANCH WIRE OR CONNECTOR (CANH, CANL)

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)
a.
U180986E02
2.365,1.281 2.74,0.906 true 0.552,3.469 0.313,3.229 true 2.063,2.104 1.594,1.729 true 2.115,2.01 2.583,2.188 0.469,0.177 10 false GND 2.771,0.823 3.021,1 0.25,0.177 10 false B 0.073,3.125 0.323,3.302 0.25,0.177 10 false IG 0.115,0.125 0.583,0.302 0.469,0.177 10 false *a 0.406,1.427 0.698,1.583 0.292,0.156 10 false G36 1.458,2.635 1.76,2.792 0.302,0.156 10 false G29

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the G36 and G29 radio and display receiver assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G36-7 (GND) - Body ground Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G29-1 (IG) - Body ground Ignition switch ON 11 to 14 V
G36-4 (B) - Body ground Always 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR