Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM
RM1440E _58 Vehicle Interior _056156 THEFT DETERRENT / KEYLESS ENTRY _0274066 ENGINE IMMOBILISER SYSTEM U

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  TERMINALS OF ECU  


CHECK TRANSPONDER KEY AMPLIFIER


U149682E03
3.427,0.26 3.719,0.417 0.292,0.156 10 false F17

a.

Disconnect the F17 amplifier connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F17-7 (AGND) - Body ground L - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the F17 amplifier connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F17-1 (VC5) - F17-7 (AGND) B - L Power supply No key in ignition key cylinder Below 1 V
Key inserted in ignition key cylinder 4.6 to 5.4 V
F17-4 (CODE) - F17-7 (AGND) LG - L Demodulated signal of key code data No key in ignition key cylinder Below 1 V
Key inserted in ignition key cylinder Pulse generation (See waveform 1)
F17-5 (TXCT) - F17-7 (AGND) V - L Key code output signal No key in ignition key cylinder Below 1 V
Key inserted in ignition key cylinder Pulse generation (See waveform 2)

If the result is not as specified, the amplifier may have a malfunction.


e.
B453107E01
0.25,1.01 0.708,1.208 0.458,0.198 10 false GND

Inspect using an oscilloscope.

i.

Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection F17-4 (CODE) - F17-7 (AGND)
Tool Setting 5 V/DIV., 20 ms./DIV.
Condition Key inserted in ignition key cylinder


ii.
B453106E01
0.26,1.063 0.719,1.26 0.458,0.198 10 false GND

Waveform 2 (Reference)

Measurement Condition
Item Content
Tester Connection F17-5 (TXCT) - F17-7 (AGND)
Tool Setting 5 V/DIV., 20 ms./DIV.
Condition Key inserted in ignition key cylinder




CHECK TRANSPONDER KEY ECU ASSEMBLY


B453108E01
3.323,0.333 3.74,0.583 0.417,0.25 3.396,0.375 3.854,0.573 0.458,0.198 10 false F34

a.

Disconnect the F34 ECU connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F34-16 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
F34-1 (+B) - F34-16 (GND) P - W-B Battery Always 11 to 14 V
F34-2 (IG) - F34-16 (GND) W - W-B Ignition switch Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
F34-3 (KSW) - F34-16 (GND) B - W-B Unlock warning switch No key in ignition key cylinder 10 kΩ or higher
Key inserted in ignition key cylinder Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the F34 ECU connector.


d.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F34-14 (VC5) - F34-16 (GND) B - W-B Power source No key in ignition key cylinder Below 1 V
Key inserted in ignition key cylinder 4.6 to 5.4 V
F34-7 (CTY) - F34-16 (GND) R - W-B Front door courtesy light switch (for Driver Side) Driver door closed 10 kΩ or higher
Driver door open Below 1 Ω
F34-4 (TXCT) - F34-16 (GND) V - W-B Transponder key amplifier communication signal No key in ignition key cylinder Below 1 V
Key inserted in ignition key cylinder Pulse generation (See waveform 1)
F34-15 (CODE) - F34-16 (GND) LG - W-B Transponder key amplifier communication signal No key in ignition key cylinder Below 1 V
Key inserted in ignition key cylinder Pulse generation (See waveform 2)
F34-13 (EFIO) - F34-16 (GND) W - W-B ECM output signal Ignition switch off Below 1 V
Ignition switch ON Pulse generation (See waveform 3)
F34-12 (EFII) - F34-16 (GND) SB - W-B ECM input signal Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected Pulse generation (See waveform 4)
F34-8 (IND) - F34-16 (GND) L - W-B Security indicator light signal Immobiliser set Alternating between 11 to 14 V and below 1 V
Immobiliser unset Below 1 V
F34-9 (D) - F34-16 (GND) G - W-B Diagnosis tester communication Always Pulse generation
F34-5 (AGND) - Body ground L - Body ground Ground Always Below 1 Ω

If the result is not as specified, the ECU may have a malfunction.


e.
B453106E01
0.26,1.063 0.719,1.26 0.458,0.198 10 false GND

Inspect using an oscilloscope.

i.

Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection F34-4 (TXCT) - F34-16 (GND)
Tool Setting 5 V/DIV., 20 ms./DIV.
Condition Key inserted in ignition key cylinder


ii.
B453107E01
0.25,1.01 0.708,1.208 0.458,0.198 10 false GND

Waveform 2 (Reference)

Measurement Condition
Item Content
Tester Connection F34-15 (CODE) - F34-16 (GND)
Tool Setting 5 V/DIV., 20 ms./DIV.
Condition Key inserted in ignition key cylinder


iii.
B237527E06
2.813,0.552 3.177,0.719 0.365,0.167 10 false GND

Waveform 3 (Reference)

Measurement Condition
Item Content
Tester Connection F34-13 (EFIO) - F34-16 (GND)
Tool Setting 10 V/DIV., 100 ms./DIV.
Condition Ignition switch ON


iv.
B229710E01
0.129,0.732 0.459,0.877 0.33,0.145 10 GND

Waveform 4 (Reference)

Measurement Condition
Item Content
Tester Connection F34-12 (EFII) - F34-16 (GND)
Tool Setting 5 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected




CHECK ECM


U149625E03
0.646,0.542 1.021,0.771 0.375,0.229 10 false F51 1.677,0.542 2.052,0.771 0.375,0.229 10 false F50 3.125,0.542 3.5,0.771 0.375,0.229 10 false B36 4.188,0.542 4.563,0.771 0.375,0.229 10 false B37 5.24,0.542 5.615,0.771 0.375,0.229 10 false B38 6.292,0.542 6.667,0.771 0.375,0.229 10 false B39

a.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F50-20 (IMO) - Body ground SB - Body ground Transponder key ECU output signal Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected Pulse generation
(See waveform 1)
F50-14 (IMI) - Body ground W - Body ground Transponder key ECU input signal Ignition switch off → ON Below 1 V → Pulse generation
(See waveform 2)

If the result is not as specified, the ECM may have a malfunction.


b.

Inspect using an oscilloscope.

i.
B229710E01
0.129,0.732 0.459,0.877 0.33,0.145 10 GND

Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection F50-20 (IMO) - Body ground
Tool Setting 5 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected


ii.
B237527E06
2.813,0.552 3.177,0.719 0.365,0.167 10 false GND

Waveform 2 (Reference)

Measurement Condition
Item Content
Tester Connection F50-14 (IMI) - Body ground
Tool Setting 10 V/DIV., 100 ms./DIV.
Condition Ignition switch ON