Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM
RM1440E _58 Vehicle Interior _056156 THEFT DETERRENT / KEYLESS ENTRY _0274066 ENGINE IMMOBILISER SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  B2799  Engine Immobiliser System Malfunction  


DESCRIPTION

This DTC is stored when one of the following occurs: 1) the ECM detects errors in its own communications with the transponder key ECU assembly; 2) the ECM detects errors in the communication lines; or 3) the ECU - ECM communication ID between the transponder key ECU assembly and ECM is different and an engine start is attempted. Before troubleshooting for this DTC, make sure no engine immobiliser DTCs are output. If output, troubleshoot the engine immobiliser DTCs first.

DTC Code DTC Detection Condition Trouble Area
B2799 One of the following conditions is met:
·

An error in communication between the ECM and transponder key ECU assembly.

·

An error in the communication lines.

·

The ECU - ECM communication ID is different during communication with the transponder key ECU assembly.


·

Harness or connector

·

Transponder key ECU assembly

·

ECM



WIRING DIAGRAM

B235863E04
1.176,2.004 1.465,2.178 0.289,0.174 10 F50 1.173,2.158 1.525,2.318 0.352,0.160 10 ECM 5.499,0.931 5.893,1.118 0.394,0.188 10 EFIO 5.499,1.388 5.893,1.575 0.394,0.188 10 EFII 1.464,0.931 1.858,1.118 0.394,0.188 10 IMI 1.433,1.4 1.827,1.587 0.394,0.188 10 IMO 1.783,0.852 2.004,1.025 0.221,0.173 10 14 1.79,1.335 2.013,1.499 0.223,0.164 10 20 5.238,0.844 5.462,1.054 0.224,0.210 10 13 5.238,1.327 5.462,1.537 0.224,0.210 10 12 4.912,1.994 5.323,2.180 0.410,0.186 10 F34 4.912,2.155 7.012,2.336 2.100,0.181 10 Transponder Key ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:

When replacing the transponder key ECU assembly and/or ECM, refer to the Service Bulletin.


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC

OK

NG

3.REREGISTER ECU - ECM COMMUNICATION ID
3.REREGISTER ECU - ECM COMMUNICATION ID
a.

Reregister the ECU - ECM communication ID (Refer to the Service Bulletin).



NEXT

4.CLEAR DTC
4.CLEAR DTC

NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC

OK

END

NG

6.CHECK CONNECTION OF CONNECTOR
6.CHECK CONNECTION OF CONNECTOR
a.

Turn the ignition switch off.


b.

Check that the connectors are properly connected to the ECM and transponder key ECU assembly.

OK:

Connectors are properly connected.




OK

7.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - ECM)

NG

CONNECT CONNECTOR CORRECTLY

7.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - ECM)
a.

Disconnect the F34 ECU connector.


b.

Disconnect the F50 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F34-13 (EFIO) - F50-14 (IMI) Always Below 1 Ω
F34-12 (EFII) - F50-20 (IMO)
F34-13 (EFIO) or F50-14 (IMI) - Body ground Always 10 kΩ or higher
F34-12 (EFII) or F50-20 (IMO) - Body ground




OK

8.REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Temporarily replace the transponder key ECU assembly with a new one (Refer to the Service Bulletin).



NEXT

9.REREGISTER ECU - ECM COMMUNICATION ID
9.REREGISTER ECU - ECM COMMUNICATION ID
a.

Reregister the ECU - ECM communication ID (Refer to the Service Bulletin).



NEXT

10.CLEAR DTC
10.CLEAR DTC

NEXT

11.CHECK FOR DTC
11.CHECK FOR DTC

OK

END (TRANSPONDER KEY ECU IS DEFECTIVE)

NG