Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM
RM1440E _58 Vehicle Interior _056156 THEFT DETERRENT / KEYLESS ENTRY _0274066 ENGINE IMMOBILISER SYSTEM U

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  DATA LIST / ACTIVE TEST  


READ DATA LIST


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Immobiliser / Data List.


e.

According to the display on the intelligent tester, read the Data List.

Immobiliser
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
D Door Courtesy SW Driver side door courtesy light switch / ON or OFF ON: Driver side door open
OFF: Driver side door closed
-
Key SW Unlock warning switch signal / ON or OFF ON: Key inserted in ignition key cylinder
OFF: No key in ignition key cylinder
-
IG SW Ignition switch signal / ON or OFF ON: Ignition switch ON
OFF: Ignition switch ACC or off
-
Immobiliser Immobiliser system status / Set or Unset Set: No key in ignition key cylinder
Unset: Key inserted in ignition key cylinder
-
Response Transponder chip data / OK or NG OK: Data OK
NG: Data error
-
Frame Error Transponder chip data / OK or NG OK: Data OK
NG: Data error
-
Different Serial Number Transponder chip data / OK or NG OK: Data OK
NG: Data error
-
Different Encrypt Code Transponder chip data / OK or NG OK: Data OK
NG: Data error
-
Abnormal Status Transponder chip data / OK or NG OK: Data OK
NG: Data error
-
BCC Malfunction Transponder chip signal / OK or NG OK: Correct data sent
NG: Incorrect data sent
-
Sub Key Sub-key code signal / Reg or Unreg Reg: Registered sub-key code sent
Unreg: Unmatching sub-key code sent
-
Master Key Master key code signal / Reg or Unreg Reg: Registered master key code sent
Unreg: Unmatching master key code sent
-
Transponder S-code Number of registered sub-keys / min.: 0, max.: 3 Number of registered sub-keys -
Transponder M-code Number of registered master keys / min.: 0, max.: 5 Number of registered master keys -
Reg Code Space Full Key registration code memory space full / Yes or No No: Possible to register more key codes
Yes: Cannot register any more key codes
-
+B +B judgment / Normal or Break Normal: Battery power supply normal
Break: Battery power supply malfunctioning
-
Antenna Coil Status Antenna coil condition / Normal or Fail Normal: Antenna coil normal
Fail: Antenna coil malfunctioning
-
EEPROM Status EEPROM status / OK or NG OK: Data OK
NG: Data error
-
E/G Start Permission Engine start permission / OK or NG OK: Engine start permitted
NG: Engine start not permitted
-
Immobi ECU Comm Spd Immobiliser ECU communication speed / Unknown, 50bps, 200bps or No Res Unknown: ECU communication speed unknown
50bps: ECU communication speed 50 bps
200bps: ECU communication speed 200 bps
No Res: ECU communication speed no response
-
The Number of DTCs Number of DTCs / Min.: 0, Max.: 255 Number of stored DTCs -



PERFORM ACTIVE TEST


HINT:

Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Immobiliser / Active Test.


e.

According to the display on the intelligent tester, perform the Active Test.

Immobiliser
Tester Display Test Part Control Range Diagnostic Note
Security Indicator Security indicator light ON/OFF The test is possible when the following conditions are met:

The key is in the ignition key cylinder.