Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM
RM1440E _58 Vehicle Interior _056156 THEFT DETERRENT / KEYLESS ENTRY _0274066 ENGINE IMMOBILISER SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  B279A  Theft Deterrent System Communication Line High Fixation  


DESCRIPTION

If the communication line (EFIO-IMI) to the transponder key ECU assembly is stuck on HI output, the ECM stores this DTC.

DTC Code DTC Detection Condition Trouble Area
B279A The communication line (EFIO-IMI) between the ECM and transponder key ECU assembly is stuck on HI output for 6 seconds or more.
·

Harness or connector

·

Transponder key ECU assembly

·

ECM



WIRING DIAGRAM

B235867E04
5.5,0.578 5.735,0.751 0.235,0.174 10 +B 4.267,0.712 5.051,0.885 0.784,0.174 10 SECURITY 1.176,1.844 1.469,2.017 0.293,0.174 10 F50 1.176,2.008 1.547,2.182 0.371,0.174 10 ECM 2.953,0.583 3.739,0.757 0.786,0.174 10 from Battery 5.28,0.492 5.415,0.665 0.136,0.174 10 1 5.5,0.983 5.851,1.157 0.352,0.174 10 EFIO 1.497,0.983 1.721,1.157 0.224,0.174 10 IMI 5.229,0.897 5.415,1.071 0.186,0.174 10 13 1.797,0.897 1.983,1.071 0.186,0.174 10 14 5.5,1.424 5.868,1.598 0.368,0.174 10 GND 4.839,1.76 5.207,1.934 0.368,0.174 10 F34 4.839,1.911 6.920,2.085 2.081,0.174 10 Transponder Key ECU Assembly 5.222,1.338 5.415,1.511 0.193,0.174 10 16

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the transponder key ECU assembly and/or ECM, refer to the Service Bulletin.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B279A is output A
DTC B279A and other DTCs are output B

HINT:

If any DTCs other than B279A are output, troubleshoot those DTCs first.




A

3.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - ECM)

B

3.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - ECM)
a.

Disconnect the F34 ECU connector.


b.

Disconnect the F50 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F34-13 (EFIO) - F50-14 (IMI) Always Below 1 Ω
F34-13 (EFIO) or F50-14 (IMI) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F34-13 (EFIO) - Body ground Always Below 1 V
F50-14 (IMI) - Body ground




OK

4.CHECK TRANSPONDER KEY ECU ASSEMBLY (OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK TRANSPONDER KEY ECU ASSEMBLY (OUTPUT)
a.

Using an oscilloscope, check the waveform.

U149789E03
2.313,1.26 1.802,2.177 false 0.771,0.031 0.948,0.219 0.177,0.188 10 false *a 4.438,2.458 4.792,2.646 0.354,0.188 10 false GND 1.708,2.167 1.969,2.354 0.26,0.188 10 false IMI 5.708,0.427 6.042,0.604 0.333,0.177 10 false B39 4.854,0.427 5.188,0.604 0.333,0.177 10 false B38 4.083,0.427 4.417,0.604 0.333,0.177 10 false B37 3.354,0.427 3.688,0.604 0.333,0.177 10 false B36 2.083,0.427 2.417,0.604 0.333,0.177 10 false F50 1.271,0.427 1.604,0.604 0.333,0.177 10 false F51

Text in Illustration
*a Component with harness connected
(ECM)
- -

Measurement Condition
Item Content
Tester Connection F50-14 (IMI) - Body ground
Tool Setting 10 V/DIV., 100 ms./DIV.
Condition Ignition switch ON

OK:

Waveform is output normally (refer to illustration).




OK

NG

5.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - BATTERY AND BODY GROUND)
5.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - BATTERY AND BODY GROUND)
a.
U149797E03
0.563,0.885 0.875,1.094 false 2.563,1.396 2.865,1.594 false 0.083,0.021 0.281,0.198 0.198,0.177 10 false *a 0.323,0.781 0.552,0.979 0.229,0.198 10 false +B 2.896,1.531 3.281,1.729 0.385,0.198 10 false GND 1.583,0.354 1.865,0.552 0.281,0.198 10 false F34

Disconnect the F34 ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F34-1 (+B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F34-16 (GND) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Transponder Key ECU Assembly)


OK

6.REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly (Refer to the Service Bulletin).



NEXT

7.REGISTER ECU - ECM COMMUNICATION ID
7.REGISTER ECU - ECM COMMUNICATION ID
a.

Register the ECU - ECM communication ID (Refer to the Service Bulletin).



NEXT

8.CLEAR DTC
8.CLEAR DTC

NEXT

9.CHECK FOR DTC
9.CHECK FOR DTC

OK

END (TRANSPONDER KEY ECU IS DEFECTIVE)

NG