Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM1440E _58 Vehicle Interior _056156 THEFT DETERRENT / KEYLESS ENTRY _0274067 THEFT DETERRENT SYSTEM D

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  SYSTEM DESCRIPTION  


THEFT DETERRENT SYSTEM DESCRIPTION


a.

The theft deterrent system is designed to deter vehicle break-ins and theft. If an attempted break-in or theft is detected, the vehicle horns and security horn sound and the hazard warning lights flash. The system detects an attempted break-in or theft when any of the following occurs: 1) the vehicle is forcibly entered; 2) the engine hood is forcibly opened; 3) the doors are unlocked without the use of a key; or 4) the cable is disconnected from the negative (-) battery terminal and then reconnected.

If the system enters the alarm sounding state, any unlocked doors automatically lock.


b.

The system has an active arming mode (refer to Active Arming Mode).


c.

Active arming mode has 4 states: disarmed state, arming preparation state, armed state and alarm sounding state.

i.

Disarmed state:

·

The alarm function is not operating.

·

The theft deterrent system is not operating.



ii.

Arming preparation state:

The theft deterrent system is not operating.


iii.

Armed state:

The theft deterrent system is operating.


iv.

Alarm sounding state:

The alarm function is operating (30 +/-5 seconds).

Alarm Method and Time
Alarm Method Hazard Warning Light Blinking (cycle of flasher relay)
Vehicle Horns Sounding (cycle of 0.4 seconds)
Security Horn Sounding (cycle of 0.4 seconds)
Security Indicator Light Illuminating
Alarm Time 30 +/-5 seconds

HINT:

If, during the alarm sounding state, one of the doors is unlocked without using a proper key, a forced door lock signal is output (refer to Forced Door Lock Control).





FUNCTION OF MAIN COMPONENT


Function Outline
Security indicator light Informs the driver of the theft deterrent system status.
Hazard warning light Begins flashing when an attempted break-in or theft is detected.
Low pitched horn Sounds when an attempted break-in or theft is detected.
High pitched horn Sounds when an attempted break-in or theft is detected.
Security horn Sounds when an attempted break-in or theft is detected.
Door courtesy light switch Detects the door open status (open or closed).
Door lock position switch Detects the door lock status (locked or unlocked).
Security courtesy switch Detects the engine hood open status (open or closed).
Main body ECU Detects the ignition switch condition (off, ACC or ON).


ACTIVE ARMING MODE


HINT:

Active arming mode starts alarm control immediately after doors are locked.


System State State Switching Condition Transfer to
1. Disarmed state Perform one of following and system changes to "Arming preparation state":
1.

With all doors and engine hood closed, lock all doors by wireless operation

2.

With all doors and engine hood closed, lock all doors using mechanical key

3.

With engine hood open, lock all doors and close engine hood


2. Arming preparation state
2. Arming preparation state Perform one of following and system changes to "Disarmed state":
1.

Unlock all doors by wireless operation

2.

Unlock all doors using mechanical key

3.

Unlock door

4.

Open engine hood

5.

Turn ignition switch to ON or ACC

6.

Reconnect battery


1. Disarmed state
Perform one of following and system changes to "Armed state":
1.

Allow 30 (+/-1.5) seconds to elapse


3. Armed state
3. Armed State Perform one of following and system changes to "Disarmed state":
1.

Unlock all doors by wireless operation

2.

Unlock all doors using mechanical key

3.

Turn ignition switch to ON or ACC


1. Disarmed state
Perform one of following and system changes to "Alarm sounding state":
1.

Open engine hood

2.

Open door

3.

Unlock all doors without wireless operation

4.

Unlock door without using mechanical key

5.

Disconnect and reconnect cable to negative (-) battery terminal

6.

Force engine ignition system to turn on without proper engine start method


4. Alarm sounding state
4. Alarm sounding state Perform one of following and system changes to "Disarmed state":
1.

Unlock all doors by wireless operation

2.

Unlock all doors using mechanical key

3.

Turn ignition switch to ON or ACC


1. Disarmed state
Perform one of following and system changes to "Armed state":
1.

Allow 30 (+/-5) seconds to elapse


3. Armed state (alarm stops sounding)


FORCED DOOR LOCK CONTROL


a.

Forced door lock control also helps to prevent the vehicle from being tampered with. When a door is unlocked and the alarm starts, the door is forced to lock by a forced door lock signal.

i.

Conditions that force the doors to lock:

·

0.4 seconds have elapsed after the previous output of a forced door lock signal.

·

The theft deterrent system is in the alarm sounding state.

·

A door is unlocked.





PANIC ALARM CONTROL


a.

Panic alarm control activates the panic alarm when the wireless transmitter panic switch is pressed. Panic alarm control operates independently from the change of theft deterrent system alarm control from the armed state to the alarm sounding state.

i.

The panic alarm is activated when the panic switch on the wireless transmitter is pressed and held for 1.0 seconds or more under the following conditions.

·

The ignition switch is off.

·

The theft deterrent system is not in the alarm sounding state.

·

Panic alarm control is not operating (the alarm is not sounding).



ii.

The panic alarm is deactivated when any of the following conditions is fulfilled during panic alarm operation.

·

The ignition switch is turned to ON.

·

The wireless transmitter lock/unlock switch is pressed.

·

30 +/-5 seconds have passed and the panic alarm has ended.

·

The theft deterrent system changes to the alarm sounding state. However, the alarm still sounds, because the theft deterrent system has changed to the alarm sounding state.

Conditions for canceling the panic alarm are the same as for alarm control.





SECURITY INDICATOR LIGHT OUTPUT


a.

The security indicator light turns on and off based on output signals from the main body ECU. However, in some cases, the actual status of the security indicator light is different from the output signals from the main body ECU.

Output
State of Theft Deterrent System Security Indicator
Output Signals from ECU Actual Lighting Condition
Disarmed state Off Off (Immobiliser system unset)
Blinking (Immobiliser system set)
Arming preparation state On On
Armed state Off Blinking
Alarm sounding state On On

Blinking Cycle
Time Security Indicator
0.2 seconds On
1.8 seconds Off

HINT:

When the engine immobiliser system is set, the security indicator light blinks during the disarmed state and armed state due to the output signals from the engine immobiliser system.