DATA LIST
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / (desired system) / Data List.
According to the display on the intelligent tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Key Unlock Warning SW | Unlock warning switch / ON or OFF | ON: Key inserted into ignition key cylinder
OFF: Key not inserted into ignition key cylinder |
- |
| ACC SW | Ignition switch status / ON or OFF | ON: Ignition switch ACC
OFF: Ignition switch off |
- |
| IG SW | Ignition switch status / ON or OFF | ON: Ignition switch ON
OFF: Ignition switch off |
- |
| RR Door Courtesy SW | Rear RH side door courtesy light switch signal / ON or OFF | ON: Rear RH side door open
OFF: Rear RH side door closed |
- |
| RL Door Courtesy SW | Rear LH side door courtesy light switch signal / ON or OFF | ON: Rear LH side door open
OFF: Rear LH side door closed |
- |
| Back Door Open | Back door lock position status / Permit or Prohibit | Permit: Back door unlocked
Prohibit: Back door locked |
- |
| Door Key SW-Lock | Door key linked lock switch signal / ON or OFF | ON: Driver side door key cylinder turned to lock position
OFF: Driver side door key cylinder not turned |
- |
| D-Door Key SW-UL | Door key linked unlock switch signal / ON or OFF | ON: Driver side door key cylinder turned to unlock position
OFF: Driver side door key cylinder not turned |
- |
| FR Door Lock Pos | Front RH side door lock position switch signal / UNLOCK or LOCK | UNLOCK: Front RH side door unlocked
LOCK: Front RH side door locked |
- |
| FR Door Courtesy | Front RH side door courtesy light switch signal / ON or OFF | ON: Front RH side door closed
OFF: Front RH side door open |
- |
| FL Door Lock Pos | Front LH side door lock position switch signal / UNLOCK or LOCK | UNLOCK: Front LH side door unlocked
LOCK: Front LH side door locked |
- |
| FL Door Courtesy | Front LH side door courtesy light switch signal / ON or OFF | ON: Front LH side door closed
OFF: Front LH side door open |
- |
| Hood Courtesy SW | Security courtesy switch / ON or OFF | ON: Engine hood open
OFF: Engine hood closed |
- |
| RR-Door Lock Pos SW | Rear RH side door lock position switch signal / ON or OFF | ON: Rear RH side door unlocked
OFF: Rear RH side door locked |
- |
| RL-Door Lock Pos SW | Rear LH side door lock position switch signal / ON or OFF | ON: Rear LH side door unlocked
OFF: Rear LH side door locked |
- |
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Key Switch Operation Locked | Tail gate control lock switch signal / ON or OFF | ON: Back door key cylinder turned to lock position
OFF: Back door key cylinder not turned |
- |
| Key Switch Operation Unlocked | Tail gate control unlock switch signal / ON or OFF | ON: Back door key cylinder turned to unlock position
OFF: Back door key cylinder not turned |
- |
| Back Door Courtesy Switch | Back door courtesy switch signal / ON or OFF | ON: Back door open
OFF: Back door closed |
- |
ACTIVE TEST
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Active Test.
According to the display on the intelligent tester, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Security Indicator | Security indicator | ON/OFF | The test is possible when the following conditions are met:
·
The key is in the ignition key cylinder |
| Vehicle Horn | Vehicle horns | ON/OFF | - |
| Security Horn | Security Horn | ON/OFF | - |