Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM › from 2012.08
RM1440E _58 Vehicle Interior _056157 LIGHTING (INT) _0274081 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Interior Light Auto Cut Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls operation of the DOME relay in order to supply power to the interior lights. When battery saving control operates while the interior lights are on, the main body ECU (multiplex network body ECU) opens the DOME relay to turn off the lights.

WIRING DIAGRAM

E262394E02
0.542,0.708 1.354,0.906 0.813,0.198 10 false from Battery 2.208,4.5 4.042,4.917 1.833,0.417 10 false to Transponder Key Amprifier (Ignition Key Cylinder Light) 4.646,2.885 6.333,3.26 1.688,0.375 10 false Main Body ECU (Multiplex Network Body ECU) 2.229,2.74 3.333,2.948 1.104,0.208 10 false to Vanity Lights 2.219,3.188 3.167,3.406 0.948,0.219 10 false to Spot Lights 2.219,3.615 3.708,3.813 1.49,0.198 10 false to Map Light Assembly 2.219,4.052 4.01,4.271 1.792,0.219 10 false to Courtesy Light Assembly* 0.281,5.24 1.604,5.438 1.323,0.198 10 false *: w/ Courtesy Light 2.708,0.844 3.188,1.021 0.479,0.177 10 false DOME 2.375,1.969 2.833,2.135 0.458,0.167 10 false DOME 5.156,1.667 5.635,1.844 0.479,0.177 10 false DOMR 4.979,1.552 5.083,1.729 0.104,0.177 10 false 2 4.656,2.698 4.917,2.875 0.26,0.177 10 false F9 2.865,1.563 2.979,1.74 0.115,0.177 10 false 2 2.875,1.292 3,1.469 0.125,0.177 10 false 5 2.208,1.552 2.323,1.729 0.115,0.177 10 false 1 2.208,1.292 2.313,1.469 0.104,0.177 10 false 3

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK SYMPTOMS
a.

Check symptoms.

Result
Result Proceed to
All the interior lights that receive power via the DOME relay do not illuminate. A
Battery saving function does not operate. B



A

2.INSPECT DOME RELAY

B

4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
2.INSPECT DOME RELAY
a.

Remove the DOME relay from the engine room relay block, junction block.


b.


OK

3.CHECK HARNESS AND CONNECTOR (DOME FUSE - DOME RELAY)

NG

REPLACE DOME RELAY

3.CHECK HARNESS AND CONNECTOR (DOME FUSE - DOME RELAY)
a.
E263135E01
0.175,0.12 0.361,0.281 0.186,0.161 10 *a

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
DOME relay terminal 5 - Body ground Ignition switch off 11 to 14 V


Text in Illustration
*a Engine Room Relay Block
(DOME Relay Terminal)



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Using the intelligent tester, perform the Active Test (See page Vehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST).

HINT:

In the Active Test, check the interior light operating state.


Main Body
Tester Display Test Part Control Range Diagnostic Note
Relay for Interior Light Auto Cut Function DOME relay ON/OFF -

OK:

Battery saving control operates.


HINT:
·

In the Active Test, selecting the DOME relay ON or OFF turns the interior light on or off.

·

After turning the ignition switch to ON, proceed to the preceding screen of the active test screen with the intelligent tester and turn the ignition switch off, and perform the active test.





OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

5.INSPECT DOME RELAY
5.INSPECT DOME RELAY
a.

Remove the DOME relay from the engine room relay block, junction block.


b.


OK

6.CHECK HARNESS AND CONNECTOR (DOME RELAY - MAIN BODY ECU, BODY GROUND)

NG

REPLACE DOME RELAY

6.CHECK HARNESS AND CONNECTOR (DOME RELAY - MAIN BODY ECU, BODY GROUND)
a.

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
DOME relay terminal 2 - F9-2 (DOMR) Always Below 1 Ω
DOME relay terminal 1 - Body ground Always Below 1 Ω
F9-2 (DOMR) - Body ground Always 10 kΩ or higher




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR