Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM1440E _58 Vehicle Interior _056158 METER / GAUGE / DISPLAY _0274083 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Entire Combination Meter does not Operate  


DESCRIPTION

This circuit is the power source circuit for the meter. This circuit provides two types of power sources; one is a constant power source mainly used as a backup power source, and the other is an IG power source mainly used for signal transmission. The constant power source is mainly used as a backup power source for the meter CPU, however, it is also used for CAN communication. If a voltage of 12 V is not applied to terminal +IG when the ignition switch is turned to ON, the indicators will not operate.

WIRING DIAGRAM

U150523E01
5.102,0.888 5.226,1.039 0.124,0.151 10 B 5.102,1.626 5.347,1.777 0.245,0.151 10 IG+ 5.102,2.911 5.300,3.062 0.198,0.151 10 E1 5.102,2.41 5.549,2.561 0.447,0.151 10 MGND 4.828,0.781 5.020,0.933 0.192,0.151 10 15 4.828,1.533 5.020,1.685 0.192,0.151 10 17 4.828,2.823 5.020,2.974 0.192,0.151 10 20 4.828,2.309 5.020,2.460 0.192,0.151 10 13 4.698,4.987 6.554,5.138 1.856,0.151 10 Combination Meter Assembly 3.065,1.842 3.594,1.993 0.529,0.151 10 GAUGE 3.074,1.093 3.558,1.244 0.483,0.151 10 ECU-B 0.916,0.909 1.699,1.060 0.782,0.151 10 from Battery 0.734,1.618 1.697,1.769 0.964,0.151 10 from IG2 Relay 4.698,4.814 4.984,4.965 0.286,0.151 10 F14

PROCEDURE

1.CHECK HARNESS AND CONNECTOR
a.
U150509E02
2.146,1.292 2.146,0.563 2.146,0.563 2.208,0.563 false 2.333,1.292 2.719,0.656 2.719,0.656 2.792,0.656 false 2.615,1.302 2.896,1.302 false 1.948,1.281 1.26,0.458 1.26,0.458 1.188,0.458 false 2.26,0.479 2.375,0.625 0.115,0.146 10 false B 2.844,0.573 3.125,0.719 0.281,0.146 10 false IG+ 2.938,1.219 3.135,1.365 0.198,0.146 10 false E1 0.708,0.375 1.24,0.604 0.531,0.229 10 false MGND 0.219,1.229 0.625,1.469 0.406,0.24 10 false F14 0.292,0.031 0.458,0.177 0.167,0.146 10 false *a

Disconnect the F14 meter connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F14-20 (E1) - Body ground Always Below 1 Ω
F14-13 (MGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F14-17 (+IG) - Body ground Ignition switch ON 11 to 14 V
F14-15 (B) - Body ground Always 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Assembly)


OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR