Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM1440E _58 Vehicle Interior _056158 METER / GAUGE / DISPLAY _0274083 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Voltage Meter Malfunction  


DESCRIPTION

The voltage meter indicates the voltage applied to the +IG terminal of the combination meter.

WIRING DIAGRAM

E200271E01
0.215,0.947 1.197,1.131 0.982,0.184 10 from IG2 Relay 2.277,1.104 2.815,1.288 0.539,0.184 10 GAUGE 3.612,0.848 3.885,1.032 0.273,0.184 10 IG+ 3.352,0.848 3.537,1.032 0.184,0.184 10 17 3.353,2.289 3.538,2.474 0.184,0.184 10 20 3.606,2.291 3.820,2.475 0.214,0.184 10 E1 4.166,1.51 5.079,1.882 0.913,0.371 10 Power Supply Circuit 5.214,0.924 5.537,1.109 0.322,0.184 10 CPU 5.6,1.89 6.011,2.075 0.411,0.184 10 VOLT 3.803,3.074 4.060,3.226 0.258,0.152 10 F14 3.803,3.242 5.680,3.387 1.878,0.145 10 Combination Meter Assembly

PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (VOLTMETER)
a.

Operate the intelligent tester according to the display and select the Active Test (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

Combination Meter
Tester Display Test Part Control Range Diagnostic Note
Volt Meter Operation Voltage meter 9, 12, 15 or 18 Perform the test with the vehicle stopped and the engine idling.

OK:

Needle indication is normal.




OK

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER - BATTERY AND BODY GROUND)

NG

REPLACE COMBINATION METER ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER - BATTERY AND BODY GROUND)
E352765E01
2.698,0.906 3.094,1.125 0.396,0.219 0.677,1.656 0.99,1.26 true 1.229,1.219 0.583,0.875 true 0.115,0.083 0.427,0.281 0.313,0.198 10 false *a 0.531,1.677 0.844,1.875 0.313,0.198 10 false E1 0.292,0.74 0.604,0.938 0.313,0.198 10 false IG+ 2.771,0.938 3.083,1.135 0.313,0.198 10 false F14

a.

Disconnect the F14 meter connector.


b.

Measure the resistance and voltage according to the value(s) in the tables below.

Standard Resistance:
Tester Connection Condition Specified Condition
F14-20 (E1) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Switch Condition Specified Condition
F14-17 (+IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V


Text in Illustration
*a Rear view of wire harness connector
(to Combination Meter Assembly)



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR