Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM1440E _58 Vehicle Interior _056158 METER / GAUGE / DISPLAY _0274083 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B1500  Fuel Sender Open Detected  


DESCRIPTION

This DTC is stored when the combination meter detects a fuel sender gauge malfunction.

DTC Code DTC Detection Condition Trouble Area
B1500 IG voltage is 9.5 V or higher and the following condition is met:
1. Fuel sender gauge operation malfunction.
·

Harness or connector

·

Combination meter assembly

·

Fuel suction with pump and gauge tube assembly

·

Fuel sender gauge assembly



WIRING DIAGRAM

E185311E02
3.377,0.943 3.598,1.104 0.221,0.161 10 FE 3.373,0.569 3.593,0.730 0.221,0.161 10 FS 3.681,0.943 3.786,1.104 0.105,0.161 10 3 3.676,0.569 3.790,0.730 0.114,0.161 10 2 4.022,0.551 4.206,0.711 0.184,0.161 10 40 4.022,0.952 4.210,1.113 0.188,0.161 10 19 4.283,0.551 4.410,0.711 0.127,0.161 10 L 4.312,0.952 4.536,1.113 0.224,0.161 10 E3 4.923,1.821 5.246,1.982 0.323,0.161 10 CPU 5.498,1.704 5.876,1.865 0.378,0.161 10 FUEL 1.818,0.971 1.923,1.132 0.105,0.161 10 2 2.948,0.971 3.062,1.132 0.114,0.161 10 3 1.487,1.425 3.372,1.595 1.885,0.170 10 Fuel Sender Gauge Assembly 0.717,2.17 3.951,2.340 3.235,0.170 10 Fuel Suction with Pump and Gauge Tube Assembly 0.717,1.978 0.947,2.133 0.230,0.156 10 Q5 4.186,4.241 6.053,4.411 1.867,0.170 10 Combination Meter Assembly 4.186,4.059 4.470,4.229 0.283,0.170 10 F14 4.017,2.923 4.201,3.084 0.184,0.161 10 20 4.279,2.923 4.488,3.084 0.209,0.161 10 E1

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (FUEL SENDER GAUGE)
a.

Use the Data List to check if the fuel receiver gauge is operating properly (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Fuel Input Fuel input signal/Min.: 0, Max.: 127.5 Current fuel level displayed Unit: Liter

OK:

Fuel amount value displayed on the intelligent tester is almost the same as needle indication.


Result
Result Proceed to
NG A
OK B



A

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER - FUEL SUCTION WITH PUMP AND BODY GROUND)

B

REPLACE COMBINATION METER ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER - FUEL SUCTION WITH PUMP AND BODY GROUND)
a.

Disconnect the F14 meter connector.


b.

Disconnect the Q5 gauge connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F14-40 (L) - Q5-2 (FS) Always Below 1 Ω
F14-19 (E3) - Q5-3 (FE)
F14-20 (E1) - Body ground
F14-40 (L) or Q5-2 (FS) - Body ground Always 10 kΩ or higher




OK

3.INSPECT FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY
a.
E180164E06
0.037,0 0.207,0.165 0.170,0.165 10 *a 1.641,0.274 1.818,0.419 0.177,0.144 10 *c 0.037,2.202 0.231,2.364 0.194,0.162 10 *b 1.641,2.807 1.818,2.972 0.177,0.165 10 *d 1.346,1.28 0.607,1.28 false 0.344,1.2 0.555,1.356 0.211,0.156 10 FE 2.28,0.438 2.492,0.594 0.211,0.156 10 FS 1.736,1.188 2.229,0.524 false

Remove the fuel suction with pump and gauge tube assembly (See page Engine / Hybrid System>1GR-FE FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-2 (FS) - B-2 Always Below 1 Ω
A-3 (FE) - B-3



Text in Illustration
*a Upper Side
*b Lower Side (to Fuel Sender Gauge Assembly)
*c Connector A
*d Connector B


OK

4.INSPECT FUEL SENDER GAUGE ASSEMBLY

NG

REPLACE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

4.INSPECT FUEL SENDER GAUGE ASSEMBLY
a.
A223150E03
0.516,2.522 0.699,2.669 0.183,0.147 10 *b 1.854,2.607 0.743,2.607 false 0.506,4.33 0.696,4.477 0.190,0.147 10 *c 1.699,4.415 0.743,4.415 false 0.695,0.7 0.885,0.847 0.190,0.147 10 *a

Remove the fuel sender gauge (See page Engine / Hybrid System>1GR-FE FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - 3 Float level F (upper) 12 to 18 Ω
Float level E (lower) 405 to 415 Ω


Text in Illustration
*a Front view of wire harness connector (to Fuel Sender Gauge Assembly)
*b Float level F (upper)
*c Float level E (lower)



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE FUEL SENDER GAUGE ASSEMBLY