Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM1440E _58 Vehicle Interior _056160 SUPPLEMENTAL RESTRAINT SYSTEMS _0274089 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1805/52  Short in Front Passenger Side Squib Circuit  B1806/52  Open in Front Passenger Side Squib Circuit  B1807/52  Short to GND in Front Passenger Side Squib Circuit  B1808/52  Short to B+ in Front Passenger Side Squib Circuit  


DESCRIPTION

The front passenger side squib circuit consists of the center airbag sensor and instrument panel passenger airbag.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front passenger side squib circuit.

DTC Code DTC Detection Condition Trouble Area
B1805/52 One of the following conditions is met:
·

The center airbag sensor detects a line short circuit signal 5 times in the front passenger side squib circuit during the primary check.

·

A front passenger side squib malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

No. 2 instrument panel wire

·

Instrument panel passenger airbag assembly (Front passenger side squib)

·

Center airbag sensor assembly


B1806/52 One of the following conditions is met:
·

The center airbag sensor detects an open circuit signal in the front passenger side squib circuit for 2 seconds.

·

A front passenger side squib malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

No. 2 instrument panel wire

·

Instrument panel passenger airbag assembly (Front passenger side squib)

·

Center airbag sensor assembly


B1807/52 One of the following conditions is met:
·

The center airbag sensor detects a short circuit to ground signal in the front passenger side squib circuit for 0.5 seconds.

·

A front passenger side squib malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

No. 2 instrument panel wire

·

Instrument panel passenger airbag assembly (Front passenger side squib)

·

Center airbag sensor assembly


B1808/52 One of the following conditions is met:
·

The center airbag sensor detects a short circuit to B+ signal in the front passenger side squib circuit for 0.5 seconds.

·

A front passenger side squib malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

No. 2 instrument panel wire

·

Instrument panel passenger airbag assembly (Front passenger side squib)

·

Center airbag sensor assembly



WIRING DIAGRAM

C361763E01
1.354,1.073 1.667,1.271 0.313,0.198 10 false P+ 1.354,2.292 1.667,2.49 0.313,0.198 10 false P- 0.229,3.313 0.542,3.51 0.313,0.198 10 false z1 0.219,3.5 2.208,3.865 1.99,0.365 10 false Front Passenger Side Squib 3.313,2.406 3.625,2.604 0.313,0.198 10 false Fz1 3.302,1.208 3.615,1.406 0.313,0.198 10 false Fz1 3.365,0.99 3.677,1.188 0.313,0.198 10 false 1 3.375,2.198 3.688,2.396 0.313,0.198 10 false 2 5.542,1.063 5.865,1.25 0.323,0.188 10 false 4 5.573,2.271 5.896,2.458 0.323,0.188 10 false 3 5.865,2.417 6.188,2.604 0.323,0.188 10 false P- 5.865,1.177 6.188,1.365 0.323,0.188 10 false P+ 5.625,3.271 5.948,3.458 0.323,0.188 10 false F33 5.635,3.448 7.156,3.708 1.521,0.26 10 false Center Airbag Sensor 1.625,1.083 1.938,1.281 0.313,0.198 10 false 2 1.625,2.292 1.938,2.49 0.313,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


HINT:

To perform the simulation method, enter check mode (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (FRONT PASSENGER SIDE SQUIB)
a.
U150321E03
2.135,2.323 2.521,2.542 false 0.635,0.76 0.635,1.156 false 1.99,2.729 2.375,3.094 false 0.531,1.198 0.719,1.375 0.188,0.177 10 false *1 1.75,1.25 1.927,1.427 0.177,0.177 10 false *2 1.646,1.521 1.833,1.698 0.188,0.177 10 false *a 2.708,1.958 2.885,2.135 0.177,0.177 10 false *3 2.615,2.49 2.792,2.667 0.177,0.177 10 false *4 2.417,3.031 2.604,3.208 0.188,0.177 10 false *b 0.469,2.219 0.698,2.385 0.229,0.167 10 false z1 1.917,0.667 2.042,0.844 0.125,0.177 10 false A 1.365,0.875 1.49,1.052 0.125,0.177 10 false C 1.25,0.875 1.375,1.052 0.125,0.177 10 false D 0.875,0.885 1,1.063 0.125,0.177 10 false E 0.677,0.896 0.802,1.073 0.125,0.177 10 false F

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connectors from the instrument panel passenger airbag.


d.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector E (orange connector).

CAUTION:

Never connect the tester to the instrument panel passenger airbag (front passenger side squib) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1805, B1806, B1807 or B1808 is not output.


HINT:

Codes other than DTC B1805, B1806, B1807 and B1808 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Front Passenger Side Squib
*2 Center Airbag Sensor
*3 Connector E
*4 SST
*a Front view of wire harness connector
(to Front Passenger Side Squib)
*b Color: Orange



OK

REPLACE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY

NG

2.CHECK CONNECTOR
2.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector E.


d.
C214773E01
0.848,1.265 1.022,1.458 0.174,0.193 10 F 1.056,1.265 1.276,1.523 0.221,0.258 10 E 1.473,1.265 1.666,1.504 0.193,0.239 10 D 0.632,0.785 0.825,0.953 0.193,0.167 10 *1 1.965,1.691 2.158,1.858 0.193,0.167 10 *2 1.586,1.265 1.798,1.486 0.211,0.221 10 C 2.144,0.963 2.337,1.147 0.193,0.184 10 A

Check that the No. 2 instrument panel wire connectors (on the instrument panel passenger airbag side) are not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.


Text in Illustration
*1 Front Passenger Side Squib
*2 Center Airbag Sensor



OK

3.CHECK FRONT PASSENGER SIDE SQUIB CIRCUIT

NG

REPLACE NO. 2 INSTRUMENT PANEL WIRE

3.CHECK FRONT PASSENGER SIDE SQUIB CIRCUIT
a.
U150323E03
0.656,0.813 0.656,1.208 false 1.823,2.74 2.198,3.104 false 1.625,2.115 1.219,2.49 false 1.854,2.104 2.198,2.479 false 0.583,1.24 0.771,1.417 0.188,0.177 10 false *1 2.063,1.281 2.24,1.458 0.177,0.177 10 false *2 1.646,1.521 1.833,1.698 0.188,0.177 10 false *a 2.635,2.021 2.813,2.198 0.177,0.177 10 false *3 2.281,3.031 2.469,3.208 0.188,0.177 10 false *b 0.49,2.24 0.656,2.406 0.167,0.167 10 false z1 2.229,0.688 2.354,0.865 0.125,0.177 10 false A 1.448,0.917 1.573,1.094 0.125,0.177 10 false C 1.823,0.927 1.948,1.104 0.125,0.177 10 false B 1.344,0.917 1.469,1.094 0.125,0.177 10 false D 0.969,0.917 1.094,1.094 0.125,0.177 10 false E 0.75,0.917 0.875,1.094 0.125,0.177 10 false F 2.281,2.458 2.49,2.604 0.208,0.146 10 false P+ 1,2.5 1.198,2.646 0.198,0.146 10 false P-

Disconnect the connectors from the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
z1-2 (P+) - Body ground Ignition switch ON Below 1 V
z1-1 (P-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z1-2 (P+) - z1-1 (P-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z1-2 (P+) - z1-1 (P-) Always 1 MΩ or higher
z1-2 (P+) - Body ground Always 1 MΩ or higher
z1-1 (P-) - Body ground Always 1 MΩ or higher



Text in Illustration
*1 Front Passenger Side Squib
*2 Center Airbag Sensor
*3 Connector E
*a Front view of wire harness connector
(to Front Passenger Side Squib)
*b Color: Orange


OK

4.CHECK CENTER AIRBAG SENSOR

NG

5.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - NO. 2 INSTRUMENT PANEL WIRE)
4.CHECK CENTER AIRBAG SENSOR
a.
C146252E05
0.847,0.924 0.967,1.073 0.119,0.149 10 F 0.965,0.923 1.106,1.085 0.141,0.163 10 E 1.323,0.926 1.451,1.075 0.128,0.149 10 D 1.452,0.926 1.580,1.089 0.128,0.163 10 C 1.827,1.438 2.002,1.600 0.174,0.163 10 *2 0.644,1.438 0.823,1.590 0.179,0.152 10 *1 0.733,0.834 0.731,1.365 false

Connect the connectors to the instrument panel passenger airbag and center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1805, B1806, B1807 or B1808 is not output.


HINT:

Codes other than DTC B1805, B1806, B1807 and B1808 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Front Passenger Side Squib
*2 Center Airbag Sensor



OK

NG

5.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - NO. 2 INSTRUMENT PANEL WIRE)
a.
U150088E03
0.646,0.813 0.646,1.219 false 1.125,0.813 1.125,1.219 false 1.635,0.813 1.635,1.219 false 1.333,2.688 0.927,2.938 false 1.667,2.677 2.365,2.958 false 0.583,1.229 0.771,1.406 0.188,0.177 10 false *1 1.073,1.229 1.25,1.406 0.177,0.177 10 false *2 1.573,1.219 1.75,1.396 0.177,0.177 10 false *3 1.938,1.219 2.115,1.396 0.177,0.177 10 false *4 1.646,1.615 1.833,1.792 0.188,0.177 10 false *a 2.594,2.125 2.771,2.302 0.177,0.177 10 false *5 0.438,2.24 0.698,2.406 0.26,0.167 10 false Fz1 2.083,0.677 2.208,0.854 0.125,0.177 10 false A 1.427,0.885 1.552,1.063 0.125,0.177 10 false C 1.75,0.896 1.875,1.073 0.125,0.177 10 false B 1.24,0.885 1.365,1.063 0.125,0.177 10 false D 0.927,0.885 1.052,1.063 0.125,0.177 10 false E 0.729,0.885 0.854,1.063 0.125,0.177 10 false F 0.667,2.917 0.875,3.094 0.208,0.177 10 false P+ 2.458,2.917 2.708,3.094 0.25,0.177 10 false P-

Restore the released activation prevention mechanism of connector B to its original condition.


b.

Disconnect the instrument panel wire connector from the No. 2 instrument panel wire.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Fz1-1 (P+) - Body ground Ignition switch ON Below 1 V
Fz1-2 (P-) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Fz1-1 (P+) - Fz1-2 (P-) Always Below 1 Ω



h.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Fz1-1 (P+) - Fz1-2 (P-) Always 1 MΩ or higher
Fz1-1 (P+) - Body ground Always 1 MΩ or higher
Fz1-2 (P-) - Body ground Always 1 MΩ or higher



Text in Illustration
*1 Front Passenger Side Squib
*2 No. 2 Instrument Panel Wire
*3 Instrument Panel Wire
*4 Center Airbag Sensor
*5 Connector C
*a Front view of wire harness connector
(to No. 2 Instrument Panel Wire)


OK

REPLACE NO. 2 INSTRUMENT PANEL WIRE

NG

REPLACE INSTRUMENT PANEL WIRE