Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM1440E _58 Vehicle Interior _056160 SUPPLEMENTAL RESTRAINT SYSTEMS _0274089 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1815/54  Short in Front Passenger Side Squib 2nd Step Circuit  B1816/54  Open in Front Passenger Side Squib 2nd Step Circuit  B1817/54  Short to GND in Front Passenger Side Squib 2nd Step Circuit  B1818/54  Short to B+ in Front Passenger Side Squib 2nd Step Circuit  


DESCRIPTION

The front passenger side squib 2nd step circuit consists of the center airbag sensor and instrument panel passenger airbag.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front passenger side squib 2nd step circuit.

DTC Code DTC Detection Condition Trouble Area
B1815/54 One of the following conditions is met:
·

The center airbag sensor detects a line short circuit signal 5 times in the front passenger side squib 2nd step circuit during the primary check.

·

A front passenger side squib 2nd step malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

No. 2 instrument panel wire

·

Instrument panel passenger airbag assembly (Front passenger side squib 2nd step)

·

Center airbag sensor assembly


B1816/54 One of the following conditions is met:
·

The center airbag sensor detects an open circuit signal in the front passenger side squib 2nd step circuit for 2 seconds.

·

A front passenger side squib 2nd step malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

No. 2 instrument panel wire

·

Instrument panel passenger airbag assembly (Front passenger side squib 2nd step)

·

Center airbag sensor assembly


B1817/54 One of the following conditions is met:
·

The center airbag sensor detects a short circuit to ground signal in the front passenger side squib 2nd step circuit for 0.5 seconds.

·

A front passenger side squib 2nd step malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

No. 2 instrument panel wire

·

Instrument panel passenger airbag assembly (Front passenger side squib 2nd step)

·

Center airbag sensor assembly


B1818/54 One of the following conditions is met:
·

The center airbag sensor detects a short circuit to B+ signal in the front passenger side squib 2nd step circuit for 0.5 seconds.

·

A front passenger side squib 2nd step malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

No. 2 instrument panel wire

·

Instrument panel passenger airbag assembly (Front passenger side squib 2nd step)

·

Center airbag sensor assembly



WIRING DIAGRAM

C361763E02
1.281,1.094 1.594,1.292 0.313,0.198 10 false P2+ 1.323,2.292 1.635,2.49 0.313,0.198 10 false P2- 0.229,3.313 0.542,3.51 0.313,0.198 10 false z2 0.219,3.5 3.115,3.917 2.896,0.417 10 false Front Passenger Side Squib 2nd Step 3.313,2.406 3.625,2.604 0.313,0.198 10 false Fz1 3.302,1.208 3.615,1.406 0.313,0.198 10 false Fz1 3.365,0.99 3.677,1.188 0.313,0.198 10 false 3 3.375,2.198 3.688,2.396 0.313,0.198 10 false 4 5.542,1.063 5.865,1.25 0.323,0.188 10 false 1 5.573,2.271 5.896,2.458 0.323,0.188 10 false 2 5.865,2.396 6.188,2.583 0.323,0.188 10 false P2- 5.865,1.177 6.188,1.365 0.323,0.188 10 false P2+ 5.625,3.271 5.948,3.458 0.323,0.188 10 false F33 5.635,3.448 7.156,3.708 1.521,0.26 10 false Center Airbag Sensor 1.625,1.083 1.938,1.281 0.313,0.198 10 false 2 1.625,2.292 1.938,2.49 0.313,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


HINT:

To perform the simulation method, enter check mode (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK INSTRUMENT PANEL PASSENGER AIRBAG (FRONT PASSENGER SIDE SQUIB 2ND STEP)
a.
U150322E03
2.135,2.344 2.521,2.563 false 0.552,0.792 0.552,1.188 false 2.01,2.729 2.385,3.094 false 0.49,1.208 0.677,1.385 0.188,0.177 10 false *1 1.74,1.24 1.917,1.417 0.177,0.177 10 false *2 1.667,1.49 1.854,1.667 0.188,0.177 10 false *a 2.729,1.958 2.906,2.135 0.177,0.177 10 false *3 2.604,2.5 2.781,2.677 0.177,0.177 10 false *4 2.49,3.073 2.677,3.25 0.188,0.177 10 false *b 0.469,2.229 0.698,2.396 0.229,0.167 10 false z2 1.906,0.656 2.031,0.833 0.125,0.177 10 false A 1.365,0.896 1.49,1.073 0.125,0.177 10 false C 1.25,0.896 1.375,1.073 0.125,0.177 10 false D 0.865,0.885 0.99,1.063 0.125,0.177 10 false E 0.667,0.885 0.792,1.063 0.125,0.177 10 false F

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connectors from the instrument panel passenger airbag.


d.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector E (black connector).

CAUTION:

Never connect the tester to the instrument panel passenger airbag (front passenger side squib 2nd step) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1815, B1816, B1817 or B1818 is not output.


HINT:

Codes other than DTC B1815, B1816, B1817 and B1818 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Front Passenger Side Squib 2nd Step
*2 Center Airbag Sensor
*3 Connector E
*4 SST
*a Front view of wire harness connector
(to Front Passenger Side Squib 2nd Step)
*b Color: Black



OK

REPLACE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY

NG

2.CHECK CONNECTOR
2.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector E.


d.
C214773E01
0.848,1.265 1.022,1.458 0.174,0.193 10 F 1.056,1.265 1.276,1.523 0.221,0.258 10 E 1.473,1.265 1.666,1.504 0.193,0.239 10 D 0.632,0.785 0.825,0.953 0.193,0.167 10 *1 1.965,1.691 2.158,1.858 0.193,0.167 10 *2 1.586,1.265 1.798,1.486 0.211,0.221 10 C 2.144,0.963 2.337,1.147 0.193,0.184 10 A

Check that the instrument panel wire connectors (on the instrument panel passenger airbag side) are not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not damaged or deformed.


Text in Illustration
*1 Front Passenger Side Squib 2nd Step
*2 Center Airbag Sensor



OK

3.CHECK FRONT PASSENGER SIDE SQUIB 2ND STEP CIRCUIT

NG

REPLACE NO. 2 INSTRUMENT PANEL WIRE

3.CHECK FRONT PASSENGER SIDE SQUIB 2ND STEP CIRCUIT
a.
U150324E03
0.646,0.813 0.646,1.208 false 1.844,2.74 2.219,3.104 false 1.635,2.104 1.229,2.479 false 1.833,2.104 2.177,2.479 false 0.583,1.24 0.771,1.417 0.188,0.177 10 false *1 2.042,1.271 2.219,1.448 0.177,0.177 10 false *2 1.76,1.438 1.948,1.615 0.188,0.177 10 false *a 2.625,2.052 2.802,2.229 0.177,0.177 10 false *3 2.323,3.042 2.51,3.219 0.188,0.177 10 false *b 0.479,2.24 0.646,2.406 0.167,0.167 10 false z2 2.219,0.677 2.344,0.854 0.125,0.177 10 false A 1.438,0.896 1.563,1.073 0.125,0.177 10 false C 1.833,0.896 1.958,1.073 0.125,0.177 10 false B 1.333,0.896 1.458,1.073 0.125,0.177 10 false D 0.958,0.896 1.083,1.073 0.125,0.177 10 false E 0.75,0.896 0.875,1.073 0.125,0.177 10 false F 2.24,2.479 2.521,2.625 0.281,0.146 10 false P2+ 0.948,2.51 1.229,2.656 0.281,0.146 10 false P2-

Disconnect the connectors from the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
z2-2 (P2+) - Body ground Ignition switch ON Below 1 V
z2-1 (P2-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z2-2 (P2+) - z2-1 (P2-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z2-2 (P2+) - z2-1 (P2-) Always 1 MΩ or higher
z2-2 (P2+) - Body ground Always 1 MΩ or higher
z2-1 (P2-) - Body ground Always 1 MΩ or higher



Text in Illustration
*1 Front Passenger Side Squib 2nd Step
*2 Center Airbag Sensor
*3 Connector E
*a Front view of wire harness connector
(to Front Passenger Side Squib 2nd Step)
*b Color: Black


OK

4.CHECK CENTER AIRBAG SENSOR

NG

5.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - NO. 2 INSTRUMENT PANEL WIRE)
4.CHECK CENTER AIRBAG SENSOR
a.
C146252E05
0.847,0.924 0.967,1.073 0.119,0.149 10 F 0.965,0.923 1.106,1.085 0.141,0.163 10 E 1.323,0.926 1.451,1.075 0.128,0.149 10 D 1.452,0.926 1.580,1.089 0.128,0.163 10 C 1.827,1.438 2.002,1.600 0.174,0.163 10 *2 0.644,1.438 0.823,1.590 0.179,0.152 10 *1 0.733,0.834 0.731,1.365 false

Connect the connectors to the instrument panel passenger airbag and center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1815, B1816, B1817 or B1818 is not output.


HINT:

Codes other than DTC B1815, B1816, B1817 and B1818 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Front Passenger Side Squib 2nd Step
*2 Center Airbag Sensor



OK

NG

5.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - NO. 2 INSTRUMENT PANEL WIRE)
a.
U150087E03
0.635,0.813 0.635,1.219 false 1.135,0.813 1.135,1.219 false 1.625,0.813 1.625,1.219 false 2.531,2.49 2.052,2.594 false 1.844,2.719 2.354,3 false 0.573,1.26 0.76,1.438 0.188,0.177 10 false *1 1.083,1.25 1.26,1.427 0.177,0.177 10 false *2 1.594,1.24 1.771,1.417 0.177,0.177 10 false *3 1.938,1.229 2.115,1.406 0.177,0.177 10 false *4 1.646,1.615 1.833,1.792 0.188,0.177 10 false *a 2.729,2.052 2.906,2.229 0.177,0.177 10 false *5 0.438,2.25 0.698,2.417 0.26,0.167 10 false Fz1 2.094,0.688 2.219,0.865 0.125,0.177 10 false A 1.438,0.917 1.563,1.094 0.125,0.177 10 false C 1.76,0.906 1.885,1.083 0.125,0.177 10 false B 1.26,0.906 1.385,1.083 0.125,0.177 10 false D 0.927,0.906 1.052,1.083 0.125,0.177 10 false E 0.729,0.917 0.854,1.094 0.125,0.177 10 false F 2.438,2.948 2.719,3.125 0.281,0.177 10 false P2+ 2.635,2.385 2.885,2.563 0.25,0.177 10 false P2-

Restore the released activation prevention mechanism of connector B to its original condition.


b.

Disconnect the instrument panel wire connector from the No. 2 instrument panel wire.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Fz1-3 (P2+) - Body ground Ignition switch ON Below 1 V
Fz1-4 (P2-) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Fz1-3 (P2+) - Fz1-4 (P2-) Always Below 1 Ω



h.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Fz1-3 (P2+) - Fz1-4 (P2-) Always 1 MΩ or higher
Fz1-3 (P2+) - Body ground Always 1 MΩ or higher
Fz1-4 (P2-) - Body ground Always 1 MΩ or higher



Text in Illustration
*1 Front Passenger Side Squib 2nd Step
*2 No. 2 Instrument Panel Wire
*3 Instrument Panel Wire
*4 Center Airbag Sensor
*5 Connector C
*a Front view of wire harness connector
(to No. 2 Instrument Panel Wire)


OK

REPLACE NO. 2 INSTRUMENT PANEL WIRE

NG

REPLACE INSTRUMENT PANEL WIRE