Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM1440E _58 Vehicle Interior _056160 SUPPLEMENTAL RESTRAINT SYSTEMS _0274089 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1825/56  Short in Side Squib LH Circuit  B1826/56  Open in Side Squib LH Circuit  B1827/56  Short to GND in Side Squib LH Circuit  B1828/56  Short to B+ in Side Squib LH Circuit  


DESCRIPTION

The side squib LH circuit consists of the center airbag sensor and front seat side airbag LH.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the side squib LH circuit.

DTC Code DTC Detection Condition Trouble Area
B1825/56 One of the following conditions is met:
·

The center airbag sensor detects a line short circuit signal 5 times in the side squib LH circuit during the primary check.

·

A side squib LH malfunction.

·

A center airbag sensor malfunction.


·

No. 2 floor wire

·

Front seat side airbag assembly LH (Side squib LH)

·

Center airbag sensor assembly


B1826/56 One of the following conditions is met:
·

The center airbag sensor detects an open circuit signal in the side squib LH circuit for 2 seconds.

·

A side squib LH malfunction.

·

A center airbag sensor malfunction.


·

No. 2 floor wire

·

Front seat side airbag assembly LH (Side squib LH)

·

Center airbag sensor assembly


B1827/56 One of the following conditions is met:
·

The center airbag sensor detects a short circuit to ground signal in the side squib LH circuit for 0.5 seconds.

·

A side squib LH malfunction.

·

A center airbag sensor malfunction.


·

No. 2 floor wire

·

Front seat side airbag assembly LH (Side squib LH)

·

Center airbag sensor assembly


B1828/56 One of the following conditions is met:
·

The center airbag sensor detects a short circuit to B+ signal in the side squib LH circuit for 0.5 seconds.

·

A side squib LH malfunction.

·

A center airbag sensor malfunction.


·

No. 2 floor wire

·

Front seat side airbag assembly LH (Side squib LH)

·

Center airbag sensor assembly



WIRING DIAGRAM

C174615E18
4.847,2.502 5.256,2.667 0.409,0.165 10 SFL- 4.847,1.648 5.302,1.814 0.455,0.166 10 SFL+ 1.928,2.602 2.355,2.766 0.427,0.165 10 SFL- 1.928,1.529 2.355,1.694 0.427,0.165 10 SFL+ 2.472,2.374 2.675,2.555 0.203,0.181 10 2 2.472,1.52 2.675,1.701 0.203,0.181 10 1 0.739,3.252 2.046,3.429 1.307,0.177 10 Side Squib LH 0.739,3.089 1.080,3.226 0.341,0.138 10 O2 4.707,4.364 6.105,4.541 1.398,0.177 10 Center Airbag Sensor 4.707,4.2 5.048,4.338 0.341,0.138 10 O1 4.561,1.555 4.783,1.721 0.222,0.166 10 1 4.559,2.369 4.781,2.535 0.222,0.166 10 2

CAUTION / NOTICE / HINT

NOTICE:

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


HINT:

To perform the simulation method, enter check mode (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK FRONT SEAT SIDE AIRBAG LH (SIDE SQUIB LH)
a.
U150342E03
2.052,2.49 2.438,2.615 false 0.979,0.625 0.979,1.156 0.979,1.156 1.177,1.156 false 1.292,0.688 1.469,0.865 0.177,0.177 10 false C 1.083,0.688 1.219,0.885 0.135,0.198 10 false D 0.594,2.021 0.802,2.177 0.208,0.156 10 false O2 1.667,1.365 1.844,1.542 0.177,0.177 10 false *2 1.573,1.708 1.76,1.885 0.188,0.177 10 false *a 2.5,2.542 2.677,2.719 0.177,0.177 10 false *4 2.583,1.948 2.76,2.125 0.177,0.177 10 false *3 1.833,0.469 1.958,0.646 0.125,0.177 10 false A 1.219,1.063 1.406,1.24 0.188,0.177 10 false *1

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connector from the front seat side airbag LH.


d.

Connect the red wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the front seat side airbag LH (side squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1825, B1826, B1827 or B1828 is not output.


HINT:

Codes other than DTC B1825, B1826, B1827 and B1828 may be output at this time, but they are not related to this check.


Result
Result Proceed to
OK A
NG B

Text in Illustration
*1 Side Squib LH
*2 Center Airbag Sensor
*3 Connector C
*4 SST
*a Front view of wire harness connector
(to Side Squib LH)



B

2.CHECK NO. 2 FLOOR WIRE (SIDE SQUIB LH CIRCUIT)

A

2.CHECK NO. 2 FLOOR WIRE (SIDE SQUIB LH CIRCUIT)
a.
U150343E03
0.958,0.615 0.958,1.167 0.958,1.167 1.01,1.167 false 1.51,0.604 1.51,1.156 1.51,1.156 1.552,1.156 false 1.51,2.531 1.094,2.719 false 1.813,2.521 2.188,2.708 false 1.302,0.708 1.479,0.885 0.177,0.177 10 false C 1.677,0.708 1.854,0.885 0.177,0.177 10 false B 1.094,0.708 1.229,0.906 0.135,0.198 10 false D 0.542,2.031 0.833,2.188 0.292,0.156 10 false O2 1.885,1.365 2.063,1.542 0.177,0.177 10 false *3 1.583,1.781 1.76,1.958 0.177,0.177 10 false *a 2.396,2.177 2.573,2.354 0.177,0.177 10 false *4 2.052,0.469 2.177,0.646 0.125,0.177 10 false A 1.073,1.073 1.26,1.25 0.188,0.177 10 false *1 1.604,1.063 1.792,1.24 0.188,0.177 10 false *2 0.625,2.688 1.021,2.833 0.396,0.146 10 false SFL+ 2.24,2.667 2.604,2.813 0.365,0.146 10 false SFL-

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector C.


d.

Disconnect the connectors from the center airbag sensor.


e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
O2-1 (SFL+) - Body ground Ignition switch ON Below 1 V
O2-2 (SFL-) - Body ground Ignition switch ON Below 1 V



g.

Turn the ignition switch off.


h.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O2-1 (SFL+) - O2-2 (SFL-) Always Below 1 Ω



j.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


k.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O2-1 (SFL+) - O2-2 (SFL-) Always 1 MΩ or higher
O2-1 (SFL+) - Body ground Always 1 MΩ or higher
O2-2 (SFL-) - Body ground Always 1 MΩ or higher



Text in Illustration
*1 Side Squib LH
*2 No. 2 Floor Wire
*3 Center Airbag Sensor
*4 Connector C
*a Front view of wire harness connector
(to Side Squib LH)


OK

3.CHECK CENTER AIRBAG SENSOR

NG

REPLACE NO. 2 FLOOR WIRE

3.CHECK CENTER AIRBAG SENSOR
a.
C146259E52
0.844,0.573 0.844,1.427 false 0.781,1.438 1.01,1.594 0.229,0.156 10 false *1 1.49,1.396 1.667,1.573 0.177,0.177 10 false *2 1,0.677 1.125,0.844 0.125,0.167 10 false D 1.125,0.677 1.26,0.844 0.135,0.167 10 false C

Connect the connectors to the front seat side airbag LH and center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1825, B1826, B1827 or B1828 is not output.


HINT:

Codes other than DTC B1825, B1826, B1827 and B1828 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Side Squib LH
*2 Center Airbag Sensor



OK

NG