The front pretensioner squib RH circuit consists of the center airbag sensor and front seat outer belt RH.
This circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the front pretensioner squib RH circuit.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B1900/73 | One of the following conditions is met:
·
The center airbag sensor detects a line short circuit signal 5 times in the front pretensioner squib RH circuit during the primary check. ·
A front pretensioner squib RH malfunction. ·
A center airbag sensor malfunction. |
·
Floor wire ·
Front seat outer belt assembly RH (Front pretensioner squib RH) ·
Center airbag sensor assembly |
| B1901/73 | One of the following conditions is met:
·
The center airbag sensor detects an open circuit signal in the front pretensioner squib RH circuit for 2 seconds. ·
A front pretensioner squib RH malfunction. ·
A center airbag sensor malfunction. |
·
Floor wire ·
Front seat outer belt assembly RH (Front pretensioner squib RH) ·
Center airbag sensor assembly |
| B1902/73 | One of the following conditions is met:
·
The center airbag sensor detects a short circuit to ground signal in the front pretensioner squib RH circuit for 0.5 seconds. ·
A front pretensioner squib RH malfunction. ·
A center airbag sensor malfunction. |
·
Floor wire ·
Front seat outer belt assembly RH (Front pretensioner squib RH) ·
Center airbag sensor assembly |
| B1903/73 | One of the following conditions is met:
·
The center airbag sensor detects a short circuit to B+ signal in the front pretensioner squib RH circuit for 0.5 seconds. ·
A front pretensioner squib RH malfunction. ·
A center airbag sensor malfunction. |
·
Floor wire ·
Front seat outer belt assembly RH (Front pretensioner squib RH) ·
Center airbag sensor assembly |
When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
To perform the simulation method, enter check mode (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the connectors from the front seat outer belt RH.
Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.
Never connect the tester to the front seat outer belt RH (front pretensioner squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.
Do not forcibly insert SST into the terminals of the connector when connecting SST.
Insert SST straight into the terminals of the connector.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
DTC B1900, B1901, B1902 or B1903 is not output.
Codes other than DTC B1900, B1901, B1902 and B1903 may be output at this time, but they are not related to this check.
| *1 | Front Pretensioner Squib RH |
| *2 | Center Airbag Sensor |
| *3 | Connector C |
| *4 | SST |
| *a | Front view of wire harness connector
(to Front Pretensioner Squib RH) |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect SST from connector C.
Check that the floor wire connector (on the front seat outer belt RH side) is not damaged.
The lock button is not disengaged, and the claw of the lock is not deformed or damaged.
| *1 | Front Pretensioner Squib RH |
| *2 | Center Airbag Sensor |
OK
NG
Disconnect the connectors from the center airbag sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| N4-1 (R+) - Body ground | Ignition switch ON | Below 1 V |
| N4-2 (R-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N4-1 (R+) - N4-2 (R-) | Always | Below 1 Ω |
Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N4-1 (R+) - N4-2 (R-) | Always | 1 MΩ or higher |
| N4-1 (R+) - Body ground | Always | 1 MΩ or higher |
| N4-2 (R-) - Body ground | Always | 1 MΩ or higher |
| *1 | Front Pretensioner Squib RH |
| *2 | Floor Wire |
| *3 | Center Airbag Sensor |
| *4 | Connector C |
| *a | Front view of wire harness connector
(to Front Pretensioner Squib RH) |
OK
NG
Connect the connectors to the front seat outer belt RH and center airbag sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
DTC B1900, B1901, B1902 or B1903 is not output.
Codes other than DTC B1900, B1901, B1902 and B1903 may be output at this time, but they are not related to this check.
| *1 | Front Pretensioner Squib RH |
| *2 | Center Airbag Sensor |
OK
NG