Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM1440E _58 Vehicle Interior _056160 SUPPLEMENTAL RESTRAINT SYSTEMS _0274089 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1905/74  Short in Front Pretensioner Squib LH Circuit  B1906/74  Open in Front Pretensioner Squib LH Circuit  B1907/74  Short to GND in Front Pretensioner Squib LH Circuit  B1908/74  Short to B+ in Front Pretensioner Squib LH Circuit  


DESCRIPTION

The front pretensioner squib LH circuit consists of the center airbag sensor and front seat outer belt LH.

This circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front pretensioner squib LH circuit.

DTC Code DTC Detection Condition Trouble Area
B1905/74 One of the following conditions is met:
·

The center airbag sensor detects a line short circuit signal 5 times in the front pretensioner squib LH circuit during the primary check.

·

A front pretensioner squib LH malfunction.

·

A center airbag sensor malfunction.


·

No. 2 floor wire

·

Front seat outer belt assembly LH (Front pretensioner squib LH)

·

Center airbag sensor assembly


B1906/74 One of the following conditions is met:
·

The center airbag sensor detects an open circuit signal in the front pretensioner squib LH circuit for 2 seconds.

·

A front pretensioner squib LH malfunction.

·

A center airbag sensor malfunction.


·

No. 2 floor wire

·

Front seat outer belt assembly LH (Front pretensioner squib LH)

·

Center airbag sensor assembly


B1907/74 One of the following conditions is met:
·

The center airbag sensor detects a short circuit to ground signal in the front pretensioner squib LH circuit for 0.5 seconds.

·

A front pretensioner squib LH malfunction.

·

A center airbag sensor malfunction.


·

No. 2 floor wire

·

Front seat outer belt assembly LH (Front pretensioner squib LH)

·

Center airbag sensor assembly


B1908/74 One of the following conditions is met:
·

The center airbag sensor detects a short circuit to B+ signal in the front pretensioner squib LH circuit for 0.5 seconds.

·

A front pretensioner squib LH malfunction.

·

A center airbag sensor malfunction.


·

No. 2 floor wire

·

Front seat outer belt assembly LH (Front pretensioner squib LH)

·

Center airbag sensor assembly



WIRING DIAGRAM

U149907E03
0.74,3.24 3.135,3.406 2.396,0.167 10 false Front Pretensioner Squib LH 2.198,1.563 2.427,1.75 0.229,0.188 10 false L+ 4.771,1.677 5.167,1.865 0.396,0.188 10 false PL+ 2.188,2.396 2.396,2.583 0.208,0.188 10 false L- 4.781,2.5 5.177,2.688 0.396,0.188 10 false PL- 2.458,1.573 2.604,1.74 0.146,0.167 10 false 1 2.479,2.385 2.635,2.542 0.156,0.156 10 false 2 4.583,1.531 4.698,1.698 0.115,0.167 10 false 5 4.583,2.375 4.708,2.542 0.125,0.167 10 false 6 4.76,4.198 5.083,4.385 0.323,0.188 10 false O1 4.75,4.354 6.198,4.563 1.448,0.208 10 false Center Airbag Sensor 0.74,3.083 1.094,3.24 0.354,0.156 10 false O4

CAUTION / NOTICE / HINT

NOTICE:

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


HINT:

To perform the simulation method, enter check mode (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK FRONT SEAT OUTER BELT LH (FRONT PRETENSIONER SQUIB LH)
a.
U150099E03
2.042,2.271 2.427,2.49 false 0.906,0.521 0.906,0.948 false 0.844,0.948 1.031,1.125 0.188,0.177 10 false *1 1.604,1.24 1.781,1.417 0.177,0.177 10 false *2 1.573,1.5 1.76,1.677 0.188,0.177 10 false *a 2.479,2.438 2.656,2.615 0.177,0.177 10 false *4 2.656,1.906 2.833,2.083 0.177,0.177 10 false *3 0.469,2.25 0.698,2.417 0.229,0.167 10 false O4 1.771,0.365 1.896,0.542 0.125,0.177 10 false A 1.229,0.594 1.354,0.771 0.125,0.177 10 false C 1.01,0.594 1.135,0.771 0.125,0.177 10 false D

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connectors from the front seat outer belt LH.


d.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the front seat outer belt LH (front pretensioner squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1905, B1906, B1907 or B1908 is not output.


HINT:

Codes other than DTC B1905, B1906, B1907 and B1908 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Front Pretensioner Squib LH
*2 Center Airbag Sensor
*3 Connector C
*4 SST
*a Front view of wire harness connector
(to Front Pretensioner Squib LH)



OK

REPLACE FRONT SEAT OUTER BELT ASSEMBLY LH

NG

2.CHECK CONNECTOR
2.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector C.


d.
C214774E01
1.086,0.944 1.279,1.183 0.193,0.239 10 D 0.881,0.456 1.074,0.624 0.193,0.167 10 *1 1.699,1.671 1.891,1.838 0.193,0.167 10 *2 1.318,0.944 1.530,1.164 0.211,0.221 10 C 1.859,0.662 2.052,0.846 0.193,0.184 10 A

Check that the floor wire connector (on the front seat outer belt LH side) is not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.


Text in Illustration
*1 Front Pretensioner Squib LH
*2 Center Airbag Sensor



OK

3.CHECK NO. 2 FLOOR WIRE (FRONT PRETENSIONER SQUIB LH CIRCUIT)

NG

REPLACE NO. 2 FLOOR WIRE

3.CHECK NO. 2 FLOOR WIRE (FRONT PRETENSIONER SQUIB LH CIRCUIT)
a.
U150100E03
0.74,0.521 0.74,0.948 false 1.271,0.521 1.271,0.948 false 1.594,2.188 1.177,2.563 true 1.74,2.188 2.083,2.563 true 0.677,0.958 0.865,1.135 0.188,0.177 10 false *1 1.656,1.24 1.833,1.417 0.177,0.177 10 false *3 1.594,1.542 1.781,1.719 0.188,0.177 10 false *a 2.646,2.01 2.823,2.188 0.177,0.177 10 false *4 0.458,2.25 0.688,2.417 0.229,0.167 10 false O4 1.781,0.365 1.906,0.542 0.125,0.177 10 false A 1.052,0.625 1.177,0.802 0.125,0.177 10 false C 1.417,0.615 1.542,0.792 0.125,0.177 10 false B 0.844,0.625 0.969,0.802 0.125,0.177 10 false D 1.198,0.958 1.385,1.135 0.188,0.177 10 false *2 0.969,2.49 1.167,2.635 0.198,0.146 10 false L+ 2.167,2.49 2.354,2.635 0.188,0.146 10 false L-

Disconnect the connectors from the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
O4-1 (L+) - Body ground Ignition switch ON Below 1 V
O4-2 (L-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O4-1 (L+) - O4-2 (L-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O4-1 (L+) - O4-2 (L-) Always 1 MΩ or higher
O4-1 (L+) - Body ground Always 1 MΩ or higher
O4-2 (L-) - Body ground Always 1 MΩ or higher



Text in Illustration
*1 Front Pretensioner Squib LH
*2 No. 2 Floor Wire
*3 Center Airbag Sensor
*4 Connector C
*a Front view of wire harness connector
(to Front Pretensioner Squib LH)


OK

4.CHECK CENTER AIRBAG SENSOR

NG

REPLACE NO. 2 FLOOR WIRE

4.CHECK CENTER AIRBAG SENSOR
a.
C146259E52
0.844,0.573 0.844,1.427 false 0.781,1.438 1.01,1.594 0.229,0.156 10 false *1 1.49,1.396 1.667,1.573 0.177,0.177 10 false *2 1,0.677 1.125,0.844 0.125,0.167 10 false D 1.125,0.677 1.26,0.844 0.135,0.167 10 false C

Connect the connectors to the front seat outer belt LH and center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1905, B1906, B1907 or B1908 is not output.


HINT:

Codes other than DTC B1905, B1906, B1907 and B1908 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Front Pretensioner Squib LH
*2 Center Airbag Sensor



OK

NG