Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › FRONT SEAT SIDE AIRBAG ASSEMBLY › from 2013.08
RM1440E _58 Vehicle Interior _056160 SUPPLEMENTAL RESTRAINT SYSTEMS _0274094 FRONT SEAT SIDE AIRBAG ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  FRONT SEAT SIDE AIRBAG ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


HINT:
·

Use the same procedure for both the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 73920A 1.INSTALL FRONT SEAT SIDE AIRBAG ASSEMBLY

CAUTION:
·

The nuts must not be reused.

·

Make sure that the seat frame assembly is not deformed. If it is, replace it with a new one.



a.

Using an E10 "TORX" socket wrench, install the front seat side airbag assembly with 2 new nuts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


b.

Attach the 2 clamps to connect the front seat side airbag wire harness.


Hide 2.INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD (for Manual Seat)

a.

Install the separate type front seatback cover with pad to the separate type front seatback spring assembly.


b.

Attach the 4 claws to install the 2 front seat headrest supports.


c.

Attach the 2 hooks to connect the seatback cover bracket to the separate type front seatback spring assembly with the nut.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

NOTICE:

After the seatback trim cover is assembled, make sure the side airbag strap is not twisted.



d.
B239195

Close the 2 fasteners and separate type front seatback cover.


e.
B277850E01
2.262,0.44 2.420,0.589 0.157,0.149 10 *1 1.657,1.612 1.958,0.524 1.958,0.524 2.233,0.524 false

Using hog ring pliers, install 3 new hog rings.

Text in Illustration
*1 Hog Ring Pliers

NOTICE:
·

Be careful not to damage the separate type front seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.




f.

Attach the fastening tape to connect the airbag wire harness.


g.

Attach the 3 airbag wire harness clamps.


h.

Attach the claw to connect the airbag connector.


i.

Install the rubber band to the separate type front seat cushion spring assembly.


Hide 3.INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD (for Power Seat)

a.

w/ Climate Control Seat System:

i.

Install the separate type front seatback cover with pad to the separate type front seatback spring assembly.


ii.

Attach the 4 claws to install the 2 front seat headrest supports.


iii.

Attach the 2 hooks to connect the seatback cover bracket to the separate type front seatback spring assembly and install the nut.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

NOTICE:

After the seatback trim cover is assembled, make sure the side airbag strap is not twisted.



iv.
B247942E01
2.262,0.393 2.492,0.586 0.230,0.193 10 *1 2.232,0.468 2.087,0.468 2.087,0.468 1.655,1.677 false

Using hog ring pliers, install new 5 hog rings.

Text in Illustration
*1 Hog Ring Pliers

NOTICE:
·

Be careful not to damage the separate type front seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.




v.

Attach the 7 hooks.


vi.

Attach the fastening tape to connect the airbag wire harness.


vii.

Attach the 3 airbag wire harness clamps.


viii.

Attach the claw to connect the airbag connector.



b.

w/o Climate Control Seat System:

i.

Install the separate type front seatback cover with pad to the separate type front seatback spring assembly.


ii.

Attach the 4 claws to install the 2 front seat headrest supports.


iii.

Attach the 2 hooks to connect the seatback cover bracket to the separate type front seatback spring assembly and install the nut.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

NOTICE:

After the seatback trim cover is assembled, make sure the side airbag strap is not twisted.



iv.

Close the 2 fasteners and separate type front seatback cover.

B242233E01
0.874,0.047 1.165,0.231 0.290,0.184 10 *A 4.279,0.047 4.569,0.231 0.290,0.184 10 *B

Text in Illustration
*A for Cloth Seat *B for Synthetic Leather Seat


v.
B277850E01
2.262,0.44 2.420,0.589 0.157,0.149 10 *1 1.657,1.612 1.958,0.524 1.958,0.524 2.233,0.524 false

Using hog ring pliers, install 3 new hog rings.

Text in Illustration
*1 Hog Ring Pliers

NOTICE:
·

Be careful not to damage the separate type front seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.




vi.

Attach the fastening tape to connect the airbag wire harness.


vii.

Attach the 3 airbag wire harness clamps.


viii.

Attach the claw to connect the airbag connector.


ix.

Install the rubber band to the separate type front seat cushion spring assembly.



Hide 71769A 4.INSTALL FRONT SEATBACK BOARD CLIP (w/ Climate Control Seat System)

Hide 71706 5.INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY (w/ Climate Control Seat System)

Hide 71100S 6.INSTALL FRONT SEAT ASSEMBLY (for Manual Seat)

Hide 71200S 7.INSTALL FRONT SEAT ASSEMBLY (for Power Seat)