Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY(for Power Seat) › from 2013.08
RM1440E _58 Vehicle Interior _056161 SEAT _0274104 FRONT SEAT ASSEMBLY(for Power Seat) A

SEAT  FRONT SEAT ASSEMBLY(for Power Seat)  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 82168 2.INSTALL NO. 2 SEAT WIRE

a.

Connect each connector and engage each clamp to install the No. 2 seat wire.


Hide 85866C 3.INSTALL SEATBACK CLIMATE CONTROL DUCT LH (w/ Climate Control Seat System)

a.

Attach the 2 claws to install the seatback climate control duct LH.


Hide 85867A 4.INSTALL SEATBACK CLIMATE CONTROL BLOWER LH (w/ Climate Control Seat System)

a.

Install the seatback climate control blower LH with the 4 screws.


b.

Connect the connector.


Hide 87510N 5.INSTALL FRONT SEATBACK HEATER ASSEMBLY LH (w/ Seat Heater System)

Hide 71074S 6.INSTALL SEPARATE TYPE FRONT SEATBACK COVER

a.
B239206E01
2.367,0.252 2.597,0.445 0.230,0.193 10 *1 2.321,0.327 2.155,0.327 2.155,0.327 1.657,1.719 false

Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 13 new hog rings.

Text in Illustration
*1 Hog Ring Pliers

NOTICE:
·

Be careful not to damage the separate type front seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.




b.
B247936

Connect the seatback cover bracket to the separate type front seatback pad.


Hide 7.INSTALL SEATBACK COVER WITH PAD

a.

w/o Climate Control Seat System:

i.

Install the seatback cover with pad to the separate type front seatback spring assembly.


ii.

Attach the 4 claws to install the 2 front seat headrest supports.


iii.

Attach the 2 hooks and connect the seatback cover bracket to the separate type front seatback spring assembly with the nut.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

NOTICE:

After the seatback cover bracket is attached, make sure the seatback cover bracket is not twisted.



iv.

Close the 2 fasteners and separate type front seatback cover.

B242233E02
0.875,0.083 1.167,0.271 0.292,0.188 10 false *A 4.281,0.083 4.573,0.271 0.292,0.188 10 false *B

Text in Illustration
*A for Cloth Seat *B for Leather Seat


v.
B239193E01
2.399,0.107 2.629,0.300 0.230,0.193 10 *1 2.353,0.181 2.187,0.181 2.187,0.181 1.688,1.574 false

Using hog ring pliers, install 3 new hog rings.

Text in Illustration
*1 Hog Ring Pliers

NOTICE:
·

Be careful not to damage the separate type front seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.





b.

w/ Climate Control Seat System:

i.

Install the seatback cover with pad to the separate type front seatback spring assembly.


ii.

Attach the 4 claws to install the 2 front seat headrest supports.


iii.

Attach the 2 hooks and connect the seatback cover bracket to the separate type front seatback spring assembly with the nut.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

NOTICE:

After the seatback cover bracket is attached, make sure the seatback cover bracket is not twisted.



iv.
B247942E01
2.262,0.393 2.492,0.586 0.230,0.193 10 *1 2.232,0.468 2.087,0.468 2.087,0.468 1.655,1.677 false

Using hog ring pliers, install 5 new hog rings.

Text in Illustration
*1 Hog Ring Pliers

NOTICE:
·

Be careful not to damage the separate type front seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.




v.

Attach the 7 hooks.


vi.

Connect the seat heater connector and attach the wire harness clamp.



Hide 71876A 8.INSTALL RECLINING ADJUSTER INSIDE COVER LH

a.

Attach the guide to install the reclining adjuster inside cover LH.


Hide 71875A 9.INSTALL RECLINING ADJUSTER INSIDE COVER RH

HINT:

Use the same procedure described for the LH side.


Hide 82192 10.INSTALL FRONT SEAT WIRE LH

a.

Connect each connector and engage each clamp to install the front seat wire LH.


Hide 85868A 11.INSTALL SEAT CUSHION CLIMATE CONTROL BRACKET LH (w/ Climate Control Seat System)

a.

Install the seat cushion climate control bracket LH with the 2 screws.


Hide 85860B 12.INSTALL SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY LH (w/ Climate Control Seat System)

a.

Attach the 4 guides to install the seat cushion climate control blower assembly LH.


b.

Connect the connector.


Hide 85866A 13.INSTALL SEAT CUSHION CLIMATE CONTROL DUCT LH (w/ Climate Control Seat System)

a.

Attach the 3 guides.


b.

Attach the 2 claws to install the seat cushion climate control duct LH.


Hide 87501B 14.INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY LH (w/ Seat Heater System)

Hide 71537D 15.INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH

B239189

a.

Move the front seat cushion edge protector LH in the direction of the arrow to attach the hook and install the front seat cushion edge protector LH.


b.

Install the screw.


Hide 71537C 16.INSTALL FRONT SEAT CUSHION EDGE PROTECTOR RH

HINT:

Use the same procedure described for the LH side.


Hide 71874A 17.INSTALL FRONT SEAT LOWER CUSHION SHIELD LH (for Driver Side)

a.

Attach the hook and clip to install the front seat lower cushion shield LH.


b.

Install the screw.


Hide 71873B 18.INSTALL FRONT SEAT LOWER CUSHION SHIELD RH (for Driver Side)

a.

Attach the hook and clip to install the front seat lower cushion shield RH.


b.

Install the screw.


Hide 71876 19.INSTALL RECLINING ADJUSTER INSIDE COVER LH

a.

Attach the claw and guide to install the reclining adjuster inside cover LH.


Hide 87510L 20.INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY LH (w/ Seat Heater System)

Hide 71072S 21.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER

B239183E01
2.384,0.219 2.614,0.412 0.230,0.193 10 *1 2.338,0.293 2.172,0.293 2.172,0.293 1.673,1.685 false

a.

Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 15 new hog rings.

Text in Illustration
*1 Hog Ring Pliers

NOTICE:
·

Be careful not to damage the separate type front seat cushion cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.




Hide 22.INSTALL SEAT CUSHION COVER WITH PAD

a.

Attach each hook to install the seat cushion cover with pad.


b.

w/ Seat Heater System:

Connect the seat heater connector and attach the 3 wire harness clamps.


Hide 71149A 23.INSTALL FRONT SEAT LEG COVER LH

B239172

a.

Move the cover in the direction of the arrow to install the front seat leg cover LH.


b.

Attach the 2 claws.


Hide 71440S 24.INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY

a.

w/o Climate Control Seat System:

i.

Install the seatback assembly with the 4 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


ii.

Attach the fastening tape to connect the airbag wire harness.


iii.

Attach the 3 airbag wire harness clamps.


iv.

Attach the claw to connect the airbag connector.


v.

Attach the 2 hooks.


vi.

Attach the clamp to connect the No. 2 seat wire.


vii.

w/ Seat Heater System:

Connect the seat heater connector and attach the wire harness clamp.


viii.

Install the rubber band to the seat cushion spring.



b.

w/ Climate Control Seat System:

i.

Install the seatback assembly with the 4 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


ii.

Attach the fastening tape to connect the airbag wire harness.


iii.

Attach the 3 airbag wire harness clamps.


iv.

Attach the claw to connect the airbag connector.


v.

Attach the 2 hooks.


vi.

Attach the clamp to connect the No. 2 seat wire.


vii.

Connect the seat heater connector and attach the wire harness clamp.



Hide 73240 25.INSTALL FRONT SEAT INNER BELT ASSEMBLY LH

Hide 71862 26.INSTALL FRONT SEAT INNER CUSHION SHIELD LH (for Driver Side)

a.

Attach the 3 claws to install the front seat inner cushion shield LH.


Hide 71861 27.INSTALL FRONT SEAT INNER CUSHION SHIELD RH (for Front Passenger Side)

a.

Attach the 4 claws to install the front seat inner cushion shield RH.


Hide 71868A 28.INSTALL FRONT SEAT NO. 1 INNER CUSHION SHIELD LH

a.
B239541

Attach the 2 claws to install the front seat No. 1 inner cushion shield LH.


Hide 84920 29.INSTALL LUMBAR SWITCH ASSEMBLY (for Driver Side)

Hide 84922C 30.INSTALL FRONT POWER SEAT SWITCH LH

Hide 71812D 31.INSTALL FRONT SEAT CUSHION SHIELD LH

a.

Attach the 3 wire harness clamps and connect the seat wire connector.

B239535


b.

Attach the 3 claws to close the wire harness cover.


c.

Connect the lifter motor connector.


d.

Remove the clip attached to the separate type front seatback spring assembly and install it to the front seat cushion shield LH.


e.

Attach the 2 clips, 3 claws and guide.


f.

Attach the guide of the front seat No. 1 inner cushion shield LH and install the screw.


Hide 84921A 32.INSTALL RECLINING POWER SEAT SWITCH KNOB

a.
B239533

Attach the 2 claws to install the reclining power seat switch knob.


Hide 84921B 33.INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB

B239531

a.

Attach the 2 claws to install the slide and vertical power seat switch knob.


Hide 71769A 34.INSTALL FRONT SEATBACK BOARD CLIP (w/ Climate Control Seat System)

a.
B341418

Install the 2 new front seatback board clips to the front seatback board sub-assembly LH.


Hide 71706 35.INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY LH (w/ Climate Control Seat System)

a.
B360695

Attach the 2 guides and 2 claws of the front seatback board clip to install the seatback board sub-assembly LH.


b.

Attach the 2 hooks to connect the 2 rubber bands.


Hide 71849 36.INSTALL SEAT ADJUSTER COVER CAP

a.

Install the 2 seat adjuster cover caps.