Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY(for Manual Seat)
RM1440E _58 Vehicle Interior _056161 SEAT _0274103 FRONT SEAT ASSEMBLY(for Manual Seat) A

SEAT  FRONT SEAT ASSEMBLY(for Manual Seat)  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 82168 2.INSTALL NO. 2 SEAT WIRE (for Driver Side)

a.

Attach the 2 clamps to install the seat wire.


b.

Connect the connector.


Hide 71552S 3.INSTALL SEPARATE TYPE FRONT SEATBACK PAD

a.

Install the seatback pad.


Hide 71074S 4.INSTALL SEPARATE TYPE FRONT SEATBACK COVER

a.
B239204E01
2.41,0.248 2.640,0.441 0.230,0.193 10 *1 2.365,0.322 2.198,0.322 2.198,0.322 1.7,1.715 false

Using hog ring pliers, install the seatback cover to the seatback pad with new hog rings.

Text in Illustration
*1 Hog Ring Pliers

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.




b.

Attach the 4 claws to install the 2 headrest supports.


c.
B239200

Connect the seatback cover bracket to the seatback pad.


d.

Install the seatback cover bracket to the seat frame with the nut.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

NOTICE:

After the seatback trim cover is assembled, make sure the side airbag strap is not twisted.



e.
B239195

Close the 2 fasteners, and then close the seatback cover.


f.
B239193E01
2.399,0.107 2.629,0.300 0.230,0.193 10 *1 2.353,0.181 2.187,0.181 2.187,0.181 1.688,1.574 false

Using hog ring pliers, install new 3 hog rings.

Text in Illustration
*1 Hog Ring Pliers


Hide 71876A 5.INSTALL RECLINING ADJUSTER INSIDE COVER LH

B239257

a.

Move the cover in the direction of the arrow to install the cover.


b.

Attach the guide.


Hide 71875A 6.INSTALL RECLINING ADJUSTER INSIDE COVER RH

HINT:

Use the same procedure described for the LH side.


Hide 82192 7.INSTALL FRONT SEAT WIRE LH

a.

Install the seat wire.


Hide 71537D 8.INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH

B239189

a.

Move the protector in the direction of the arrow to attach the hook and install the protector.


b.

Install the screw.


Hide 71537C 9.INSTALL FRONT SEAT CUSHION EDGE PROTECTOR RH

HINT:

Use the same procedure described for the LH side.


Hide 71874A 10.INSTALL FRONT SEAT LOWER CUSHION SHIELD LH

a.

Attach the hook and clip to install the cushion shield.


b.

Install the screw.


Hide 71873B 11.INSTALL FRONT SEAT LOWER CUSHION SHIELD RH

a.

Attach the hook and clip to install the cushion shield.


b.

Install the screw.


Hide 71876 12.INSTALL RECLINING ADJUSTER INSIDE COVER LH

a.

Attach the claw and guide to install the cover.


Hide 71072S 13.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER

B246267E01
2.335,0.472 2.517,0.647 0.182,0.175 10 *1 2.322,0.575 2.215,0.575 false 2.215,0.575 1.828,1.67 false

a.

Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.

Text in Illustration
*1 Hog Ring Pliers

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.




Hide 14.INSTALL SEAT CUSHION COVER WITH PAD

a.

Install the seat cushion cover with pad.


b.

for Front Passenger Side:

Attach the claw to connect the connector.


c.

Attach the hooks.


Hide 71149A 15.INSTALL FRONT SEAT LEG COVER LH

B239172

a.

Move the cover in the direction of the arrow to install the cover.


b.

Attach the 2 claws.


Hide 71849 16.INSTALL SEAT ADJUSTER COVER CAP

a.

Install the 2 caps.


Hide 71440S 17.INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY

a.

Install the seatback assembly with the 4 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


b.

Connect the airbag wire harness.


c.

Attach the fastening tape to close the cover.


d.

Attach the 3 airbag wire harness clamps.


e.

Attach the claw and disconnect the airbag connector.


f.

Install the 2 clips.


g.

for Driver Side:

Attach the clamp to connect the No. 2 seat wire.


h.

Install the rubber band to the seat cushion spring.


Hide 73240 18.INSTALL FRONT SEAT INNER BELT ASSEMBLY LH

Hide 71862 19.INSTALL FRONT SEAT INNER CUSHION SHIELD LH

B239168

a.

Attach the 3 claws to install the cushion shield.


Hide 71861 20.INSTALL FRONT SEAT INNER CUSHION SHIELD RH (for Front Passenger Side)

a.

Attach the 4 claws to install the cushion shield.


Hide 84920 21.INSTALL LUMBAR SWITCH ASSEMBLY (for Driver Side)

Hide 71812D 22.INSTALL FRONT SEAT CUSHION SHIELD LH

a.

for Driver Side:

Attach the 5 wire harness clamps and connect the 2 connectors.


b.
B239164

Attach the 4 claws and clip to install the cushion shield.


c.

Install the screw.


Hide 72495 23.INSTALL VERTICAL ADJUSTING HANDLE LH (for Driver Side)

a.

Install the handle with the screw.


Hide 72526 24.INSTALL RECLINING ADJUSTER RELEASE HANDLE LH

B238106

a.

Attach the claw to install the handle.