Wear protective gloves. Sharp areas on the parts may injure your hands.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
1.INSTALL FRONT SEAT SIDE AIRBAG ASSEMBLY
82168
2.INSTALL NO. 2 SEAT WIRE
Attach the 2 clamps to install the seat wire.
for Driver Side:
Connect the 2 connectors.
for Front Passenger Side:
Connect the connector.
71552S
3.INSTALL SEPARATE TYPE FRONT SEATBACK PAD
Install the seatback pad.
71074S
4.INSTALL SEPARATE TYPE FRONT SEATBACK COVER
Using hog ring pliers, install the seatback cover to the seatback pad with new hog rings.
| *1 | Hog Ring Pliers |
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
Attach the 4 claws to install the 2 headrest supports.
Connect the seatback cover bracket to the seatback pad.
Install the seatback cover bracket to the seat frame with the nut.
After the seatback trim cover is assembled, make sure the side airbag strap is not twisted.
Close the 2 fasteners, and then close the seatback cover.
| *A | for Cloth Seat | *B | for Leather Seat |
Using hog ring pliers, install 3 new hog rings.
| *1 | Hog Ring Pliers |
71876A
5.INSTALL RECLINING ADJUSTER INSIDE COVER LH
Attach the guide to install the cover.
71875A
6.INSTALL RECLINING ADJUSTER INSIDE COVER RH
Attach the guide to install the cover.
82192
7.INSTALL FRONT SEAT WIRE LH
Install the seat wire.
87501B
8.INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY LH (w/ Seat Heater System)
71537D
9.INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH
Move the protector in the direction of the arrow to attach the hook and install the protector.
Install the screw.
71537C
10.INSTALL FRONT SEAT CUSHION EDGE PROTECTOR RH
Use the same procedure described for the LH side.
71874A
11.INSTALL FRONT SEAT LOWER CUSHION SHIELD LH
Attach the hook and clip to install the cushion shield.
Install the screw.
71873B
12.INSTALL FRONT SEAT LOWER CUSHION SHIELD RH
Attach the hook and clip to install the cushion shield.
Install the screw.
71876
13.INSTALL RECLINING ADJUSTER INSIDE COVER LH
Attach the claw and guide to install the cover.
71072S
14.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER
Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.
| *1 | Hog Ring Pliers |
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
15.INSTALL SEAT CUSHION COVER WITH PAD
Install the seat cushion cover with pad.
for Front Passenger Side:
Attach the claw to connect the connector.
w/ Seat Heater System:
Connect the seat heater connector and attach the 3 wire harness clamps.
Attach the hooks.
71149A
16.INSTALL FRONT SEAT LEG COVER LH
Move the cover in the direction of the arrow to install the cover.
Attach the 2 claws.
71849
17.INSTALL SEAT ADJUSTER COVER CAP
Install the 2 caps.
71440S
18.INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY
Install the seatback assembly with the 4 bolts.
Connect the airbag wire harness.
Attach the fastening tape to close the cover.
Attach the 3 airbag wire harness clamps.
Attach the claw to connect the airbag connector.
Attach the 2 hooks.
Attach the clamp to connect the No. 2 seat wire.
w/ Seat Heater System:
Connect the seat heater connector and attach the wire harness clamp.
Install the rubber band to the seat cushion spring.
73240
19.INSTALL FRONT SEAT INNER BELT ASSEMBLY LH
71862
20.INSTALL FRONT SEAT INNER CUSHION SHIELD LH
Attach the 3 claws to install the cushion shield.
71861
21.INSTALL FRONT SEAT INNER CUSHION SHIELD RH (for Front Passenger Side)
Attach the 4 claws to install the cushion shield.
71868A
22.INSTALL FRONT SEAT NO. 1 INNER CUSHION SHIELD LH
Attach the 2 claws to install the cushion shield.
84920
23.INSTALL LUMBAR SWITCH ASSEMBLY (for Driver Side)
84922C
24.INSTALL FRONT POWER SEAT SWITCH LH
71812D
25.INSTALL FRONT SEAT CUSHION SHIELD LH
Attach the 3 wire harness clamps and connect the seat wire connector.
Attach the 3 claws to close the wire harness cover.
Remove the clip attached to the seat cushion spring and install it to the cushion shield.
Attach the 2 clips, 3 claws and guide.
Attach the guide of the front seat No. 1 inner cushion shield and install the screw.
Connect the lifter motor connector.
84921A
26.INSTALL RECLINING POWER SEAT SWITCH KNOB
Attach the 2 claws to install the knob.
84921B
27.INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB
Attach the 2 claws to install the knob.