Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING › 2009.08–2013.08
RM1440E _58 Vehicle Interior _056165 INTERIOR PANELS / TRIM _0274158 ROOF HEADLINING A

INTERIOR PANELS / TRIM  ROOF HEADLINING  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

A bolt without a torque specification is shown in the standard bolt chart (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


PROCEDURE

Hide 64746F 1.INSTALL DECK SIDE TRIM CUP HOLDER LH (w/ Rear No. 2 Seat)

a.

Attach the 2 claws to install the deck side trim cup holder.


b.

Install the 4 screws.


Hide 64745H 2.INSTALL DECK SIDE TRIM CUP HOLDER RH (w/ Rear No. 2 Seat)

HINT:

Use the same procedure described for the LH side.


Hide 62605Q 3.INSTALL QUARTER TRIM LID SUB-ASSEMBLY RH (w/ Rear No. 2 Seat)

a.

Attach the 4 claws and 2 guides to install the quarter trim lid.


Hide 73372 4.INSTALL REAR SEAT SHOULDER BELT HANGER LH (w/ Rear No. 2 Seat)

a.

Attach the claw and guide to install the rear seat shoulder belt hanger.


Hide 73371 5.INSTALL REAR SEAT SHOULDER BELT HANGER RH (w/ Rear No. 2 Seat)

HINT:

Use the same procedure described for the LH side.


Hide 64754B 6.INSTALL REAR FLOOR FINISH SIDE PLATE LH (w/o Rear No. 2 Seat)

a.

Attach the claw and 2 guides to install the rear floor finish side plate.


b.

Install the 2 screws.


Hide 64753B 7.INSTALL REAR FLOOR FINISH SIDE PLATE RH (w/o Rear No. 2 Seat)

HINT:

Use the same procedure described for the LH side.


Hide 62597A 8.INSTALL SIDE TRIM BOX LH (w/o Rear No. 2 Seat)

a.

Attach the 8 claws to install the side trim box.


b.

Install the 2 screws.


Hide 62597A 9.INSTALL SIDE TRIM BOX RH (w/o Rear No. 2 Seat)

HINT:

Use the same procedure described for the LH side.


Hide 64746 10.INSTALL REAR COMBINATION LIGHT SERVICE COVER LH

a.

Attach the 2 claws and 2 guides to install the rear combination light service cover.


Hide 64745 11.INSTALL REAR COMBINATION LIGHT SERVICE COVER RH

HINT:

Use the same procedure described for the LH side.


Hide 64766 12.INSTALL QUARTER TRIM JACK COVER SUB-ASSEMBLY

a.

Attach the 3 claws and 2 guides to install the quarter trim jack cover.


Hide 62627B 13.INSTALL QUARTER TRIM COVER

HINT:

Use the same procedure for the other quarter trim cover.


a.

Attach the 2 claws to install the quarter trim cover.


Hide 66426B 14.INSTALL REAR NO. 3 SIDE RAIL SPACER LH (w/ Rear No. 2 Seat)

a.

Attach the 2 claws to install the rear No. 3 side rail spacer.


Hide 66416 15.INSTALL REAR NO. 3 SIDE RAIL SPACER RH (w/ Rear No. 2 Seat)

HINT:

Use the same procedure described for the LH side.


Hide 66425A 16.INSTALL REAR NO. 2 SIDE RAIL SPACER LH (w/o Rear No. 2 Seat)

a.

Attach the 3 claws to install the rear No. 2 side rail spacer.


Hide 66415A 17.INSTALL REAR NO. 2 SIDE RAIL SPACER RH (w/o Rear No. 2 Seat)

HINT:

Use the same procedure described for the LH side.


Hide 73024 18.INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

a.

Attach the 4 claws to install the front shoulder belt anchor plate.


Hide 73023 19.INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 63310 20.INSTALL ROOF HEADLINING ASSEMBLY

B240031

HINT:

Before installing the roof headlining, move the front seats and rear No. 1 seat to the positions shown in the illustration.


a.

Place the roof headlining into the vehicle through the back door.

NOTICE:

Be careful not to damage the roof headlining when placing it in the cabin.



b.
B240028

w/o Sliding Roof:

i.

Install the roof headlining with the 5 clips.



c.
B240029E02
0.906,2.24 0.906,2.917 true 0.625,2.24 0.906,2.917 true 1.167,2.24 0.896,2.917 true 0.885,1.021 0.885,0.344 true 1.167,1.021 0.885,0.344 true 0.615,1.021 0.885,0.344 true 1.354,1.49 1.917,1.656 true 1.354,1.75 1.917,1.667 true 1.354,1.281 1.917,1.656 true 1.344,1.99 1.906,1.667 true 0.375,2.771 0.219,2.771 false 0.219,2.771 0.469,2 true 0.365,0.479 0.208,0.479 false 0.208,0.479 0.469,1.26 true 0.354,0.375 0.604,0.563 0.25,0.188 10 false *1 0.406,2.667 0.656,2.854 0.25,0.188 10 false *1 0.844,2.927 1.094,3.115 0.25,0.188 10 false *2 1.938,1.563 2.188,1.75 0.25,0.188 10 false *2 0.802,0.156 1.052,0.344 0.25,0.188 10 false *2

w/ Sliding Roof:

i.

Attach the 2 guides and 10 fasteners to install the roof headlining.

Text in Illustration
*1 Guide
*2 Fastener



d.

Connect the connector and attach the 5 clamps to the front pillar LH.


e.

w/ Sliding Roof:

Connect the drive gear connector.


f.

w/ EC Mirror:

Connect the inner mirror connector.


Hide 62440 21.INSTALL ROOF SIDE RAIL GARNISH ASSEMBLY LH

a.

Attach the 3 clips to install the roof side rail garnish.


Hide 62430 22.INSTALL ROOF SIDE RAIL GARNISH ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 81240 23.INSTALL NO. 1 ROOM LIGHT ASSEMBLY

Hide 87834 24.INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

Hide 74348 27.INSTALL VISOR HOLDER

HINT:

Use the same procedure for the other visor holder.


a.

Attach the 2 claws.


b.

Push in the visor holder to install it.


Hide 74320 28.INSTALL VISOR ASSEMBLY LH

a.

Install the visor with the 2 screws.


Hide 74310 29.INSTALL VISOR ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 74318 30.INSTALL VISOR BRACKET COVER LH

a.

Attach the 4 claws to install the visor bracket cover.


Hide 74317 31.INSTALL VISOR BRACKET COVER RH

HINT:

Use the same procedure described for the LH side.


Hide 74631C 32.INSTALL COAT HOOK

HINT:

Use the same procedure for the other coat hook.


a.

Install the coat hook with the screw.


b.

Attach the claw to close the cover.


Hide 74610U 33.INSTALL REAR ASSIST GRIP ASSEMBLY

B131970

HINT:

Use the same procedure for the other rear assist grip.


a.

Assemble the rear assist grip as shown in the illustration.


b.
B203056

Install the rear assist grip.


Hide 74610A 34.INSTALL ASSIST GRIP SUB-ASSEMBLY

B203057

HINT:

Use the same procedure for the other assist grip.


a.

Assemble the assist grip as shown in the illustration.


b.
B203058

Install the assist grip.


Hide 62560C 35.INSTALL REAR WINDOW SIDE GARNISH ASSEMBLY LH

a.

Attach the 6 claws and 2 guides and pass the rear No. 1 seat outer belt floor anchor through the rear window side garnish.


b.

Attach the 7 clips and 4 guides to install the rear window side garnish.


Hide 62550F 36.INSTALL REAR WINDOW SIDE GARNISH ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 62580F 37.INSTALL REAR NO. 2 WINDOW SIDE GARNISH ASSEMBLY LH

a.

w/ Rear No. 2 Seat:

i.

Attach the 7 claws and guide and pass the rear No. 2 seat outer belt floor anchor through the rear No. 2 window side garnish.



b.

Attach the 6 clips and guide to install the rear No. 2 window side garnish.


Hide 62570D 38.INSTALL REAR NO. 2 WINDOW SIDE GARNISH ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 64740C 39.INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH

a.

w/o Rear No. 2 Seat:

i.

Pass the rear seatback lock control lever base through the deck trim side panel.


ii.

Attach the 6 claws and 2 guides to install the rear seatback lock control lever base to the deck trim side panel.


iii.

Attach the 7 clips, 5 claws and 2 guides to install the deck trim side panel.


iv.

Install the 3 bolts and 2 screws.


v.

Install the rear No. 1 seat outer belt floor anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)



b.

w/ Rear No. 2 Seat:

i.

Attach the 7 clips, 5 claws and 2 guides to install the deck trim side panel.


ii.

Install the 3 bolts and 2 screws.


iii.

Install the rear No. 1 seat outer belt floor anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


iv.

Install the rear No. 2 seat outer belt floor anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)



Hide 64730B 40.INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH

a.

w/o Rear No. 2 Seat:

i.

Connect the connector.


ii.

Pass the rear seatback lock control lever base through the deck trim side panel.


iii.

Attach the 6 claws and 2 guides to install the rear seatback lock control lever base to the deck trim side panel.


iv.

Attach the 7 clips, 5 claws and 2 guides to install the deck trim side panel.


v.

Install the 3 bolts and 2 screws.


vi.

Install the rear No. 1 seat outer belt floor anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)



b.

w/ Rear No. 2 Seat:

i.

Connect the connector.


ii.

Attach the 7 clips, 5 claws and 2 guides to install the deck trim side panel.


iii.

Install the 3 bolts and 2 screws.


iv.

Install the rear No. 1 seat outer belt floor anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


v.

Install the rear No. 2 seat outer belt floor anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)



Hide 64713F 41.INSTALL FRONT DECK SIDE TRIM COVER LH

a.

Attach the 2 claws to install the front deck side trim cover.


Hide 64712F 42.INSTALL FRONT DECK SIDE TRIM COVER RH

HINT:

Use the same procedure described for the LH side.


Hide 64725J 43.INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

HINT:

Use the same procedure for the other No. 1 luggage compartment trim hook .


a.

Install the No. 1 luggage compartment trim hook by turning it clockwise.


Hide 73233A 44.INSTALL REAR NO. 1 SEAT OUTER LAP BELT ANCHOR COVER

HINT:

Use the same procedure for the other rear No. 1 seat outer lap belt anchor cover.


a.

Attach the 3 claws to install the rear No. 1 seat outer lap belt anchor cover.


Hide 45.INSTALL REAR FLOOR CARPET ASSEMBLY (w/ Deck Board)

a.

Attach the 4 claws to install the rear floor carpet.


Hide 58570C 46.INSTALL REAR FLOOR CARPET ASSEMBLY (w/o Deck Board)

a.

Attach the 4 claws to install the rear floor carpet.


Hide 58574A 47.INSTALL REAR FLOOR MAT REAR SUPPORT PLATE

a.

Attach the 5 clips to install the rear floor mat rear support plate.


Hide 58306A 48.INSTALL INNER FLOOR SIDE RAIL SUB-ASSEMBLY (w/ Deck Board)

a.

Install the inner floor side rail with the 2 bolts..


Hide 58410R 49.INSTALL DECK BOARD ASSEMBLY (w/ Deck Board)

a.

Attach the 2 guides to install the deck board.


b.

Install the 8 bolts.


Hide 58704A 50.INSTALL LUGGAGE COMPARTMENT SIDE COVER SUB-ASSEMBLY LH (w/ Deck Board)

a.

Attach the 4 clips and 2 guides to install the luggage compartment side cover.


Hide 58703A 51.INSTALL LUGGAGE COMPARTMENT SIDE COVER SUB-ASSEMBLY RH (w/ Deck Board)

HINT:

Use the same procedure described for the LH side.


Hide 58480B 52.INSTALL REAR NO. 2 FLOOR BOARD ASSEMBLY (w/ Deck Board)

a.

Attach the 3 clips to install the rear No. 2 floor board.


Hide 58408D 53.INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY (w/ Deck Board)

a.

Attach the 2 clips and 2 guides to install the No. 2 deck board.


Hide 64722B 54.INSTALL NO. 2 LUGGAGE COMPARTMENT TRIM COVER (w/ Deck Board, w/o Rear No. 2 Seat)

HINT:

Use the same procedure for all No. 2 luggage compartment trim covers.


a.

Install the luggage hold belt striker and No. 2 luggage compartment trim cover with the bolt.


b.

Attach the 2 claws to close the cover.


Hide 58401A 55.INSTALL NO. 1 DECK BOARD SUB-ASSEMBLY (w/o Deck Board)

a.

Attach the clip to install the No. 1 deck board.


Hide 64721B 56.INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM COVER (w/o Deck Board)

HINT:

Use the same procedure for the other No. 1 luggage compartment trim cover.


a.

Install the luggage hold belt striker and No. 1 luggage compartment trim cover with the bolt.


b.

Attach the 4 claws to close the cover.


Hide 62412 57.INSTALL CENTER PILLAR GARNISH LH

a.

Pass the rear front seat outer belt floor anchor through the center pillar garnish.


b.

Attach the 2 clips and 2 guides to install the center pillar garnish.


c.

Install the bolt.


Hide 62411 58.INSTALL CENTER PILLAR GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 62414A 59.INSTALL LOWER CENTER PILLAR GARNISH LH

a.

Attach the 4 claws and 2 clips to install the lower center pillar garnish.


b.

Install the front seat outer belt floor anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 62413A 60.INSTALL LOWER CENTER PILLAR GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 73233 61.INSTALL OUTER LAP BELT ANCHOR COVER

HINT:

Use the same procedure for the other outer lap belt anchor cover.


a.

Attach the 3 claws to install the outer lap belt anchor cover.


Hide 62332C 62.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

B240010E02
0.906,1.51 1.208,1.385 false 1.208,1.385 1.292,1.385 false 0.979,0.906 1.198,1.135 0.219,0.229 10 false *2 1.292,1.292 1.51,1.521 0.219,0.229 10 false *1

a.

Align the paint mark on the rear door opening trim weatherstrip with the mark position on the vehicle and install the rear door opening trim weatherstrip as shown in the illustration.

Text in Illustration
*1 Paint Mark
*2 Mark Position


Hide 62331C 63.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure described for the LH side.


Hide 67918D 64.INSTALL REAR DOOR SCUFF PLATE LH

a.

Attach the 3 clips, 6 claws and 2 guides to install the rear door scuff plate.


Hide 67917C 65.INSTALL REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure described for the LH side.


Hide 67934 66.INSTALL QUARTER SCUFF PLATE LH (w/ Rear No. 2 Seat)

a.

Install the quarter scuff plate with the 2 bolts.


Hide 67933 67.INSTALL QUARTER SCUFF PLATE RH (w/ Rear No. 2 Seat)

HINT:

Use the same procedure described for the LH side.


Hide 58371F 68.INSTALL REAR NO. 1 FLOOR STEP COVER (w/ Rear No. 2 Seat)

HINT:

Use the same procedure for all rear No. 1 floor step covers.


a.

Attach the 2 claws to install the rear No. 1 floor step cover.


Hide 62212 69.INSTALL FRONT PILLAR GARNISH LH

B240013E01
0.895,1.278 1.190,1.545 0.295,0.267 10 *1 0.663,1.65 0.841,1.39 false 0.841,1.39 0.938,1.39 false

a.

Install a new clip to the front pillar garnish.

Text in Illustration
*1 New Clip


b.

Attach the 2 guides and 2 clips to install the front pillar garnish.


Hide 62211 70.INSTALL FRONT PILLAR GARNISH RH

a.

Attach the 3 guides to install the front pillar garnish.


Hide 74611F 71.INSTALL NO. 1 ASSIST GRIP

a.

Attach the 2 claws to install the No. 1 assist grip.


b.

Install the 2 bolts.


Hide 74617A 72.INSTALL ASSIST GRIP PLUG

HINT:

Use the same procedure for the other assist grip plug.


a.

Attach the 2 claws to install the assist grip plug.


Hide 62312B 73.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

B240008E02
2.615,1.5 2.708,1.365 false 2.708,1.365 2.927,1.365 false 2.969,1.281 3.167,1.479 0.198,0.198 10 false *1 2.313,0.885 2.51,1.083 0.198,0.198 10 false *2

a.

Align the paint mark on the front door opening trim weatherstrip with the mark position on the vehicle and install the front door opening trim weatherstrip as shown in the illustration.

Text in Illustration
*1 Paint Mark
*2 Mark Position


Hide 62311B 74.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure described for the LH side.


Hide 62112 75.INSTALL COWL SIDE TRIM BOARD LH

a.

Attach the clip and claw to install the cowl side trim board.


Hide 62111C 76.INSTALL COWL SIDE TRIM BOARD RH

HINT:

Use the same procedure described for the LH side.


Hide 67920 77.INSTALL DOOR SCUFF PLATE ASSEMBLY LH

a.

Attach the 4 clips, 10 claws and 2 guides to install the door scuff plate.


Hide 67910 78.INSTALL DOOR SCUFF PLATE ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 79.INSTALL REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)

a.

Install the rear No. 2 seat assembly (See page Vehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY>INSTALLATION).


Hide 80.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).