Home › Vehicle Interior › SEAT › REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Double-folding Seat Type RH Side)
RM1440E _58 Vehicle Interior _056161 SEAT _0274106 REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Double-folding Seat Type RH Side) A

SEAT  REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Double-folding Seat Type RH Side)  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


HINT:

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).


PROCEDURE

Hide 72691B 1.INSTALL REAR SEAT CUSHION LOCK STRIKER

a.

Install the striker with the 2 bolts.

Torque:
13 N*m (127 kgf*cm, 9 ft.*lbf)


Hide 72601 2.INSTALL REAR NO. 2 SEATBACK LOCK STRIKER SUB-ASSEMBLY RH

B238022E05
3.083,1.708 3.292,1.896 0.208,0.188 10 true (1) 0.656,0.688 0.865,0.875 0.208,0.188 10 true (2)

a.

Attach the claw and install the striker with the 2 bolts.


b.

Tighten the bolts in the order indicated in the illustration.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 64730B 3.INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH

Hide 64712F 4.INSTALL FRONT DECK SIDE TRIM COVER RH

Hide 64725J 5.INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

Hide 73233A 6.INSTALL REAR NO. 1 SEAT OUTER LAP BELT ANCHOR COVER

Hide 7.INSTALL REAR FLOOR CARPET ASSEMBLY (w/ Deck Board)

a.

Attach the 4 claws to install the rear floor carpet.


Hide 58570C 8.INSTALL REAR FLOOR CARPET ASSEMBLY (w/o Deck Board)

Hide 58574A 9.INSTALL REAR FLOOR MAT REAR SUPPORT PLATE

Hide 58306A 10.INSTALL INNER FLOOR SIDE RAIL SUB-ASSEMBLY (w/ Deck Board)

Hide 58410R 11.INSTALL DECK BOARD ASSEMBLY (w/ Deck Board)

Hide 58704A 12.INSTALL LUGGAGE COMPARTMENT SIDE COVER SUB-ASSEMBLY LH (w/ Deck Board)

Hide 58703A 13.INSTALL LUGGAGE COMPARTMENT SIDE COVER SUB-ASSEMBLY RH (w/ Deck Board)

Hide 58480B 14.INSTALL REAR NO. 2 FLOOR BOARD ASSEMBLY (w/ Deck Board)

Hide 58408D 15.INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY (w/ Deck Board)

Hide 64722B 16.INSTALL NO. 2 LUGGAGE COMPARTMENT TRIM COVER (w/Deck Board, w/o Rear No. 2 Seat)

HINT:

Use the same procedure for all No. 2 luggage compartment trim covers.


a.

Install the luggage hold belt striker and No. 2 luggage compartment trim cover with the bolt.


b.

Attach the 2 claws to close the cover.


Hide 58401A 17.INSTALL NO. 1 DECK BOARD SUB-ASSEMBLY (w/o Deck Board)

Hide 64721B 18.INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM COVER (w/o Deck Board)

Hide 62331C 19.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

Hide 72677A 21.INSTALL REAR SEATBACK LOCK CONTROL LEVER BASE RH

a.

Attach the cable clamp to connect the cable.


b.
B238020

Move the cover in the direction of the arrow to attach the 2 guides.


c.

Attach the 6 claws to install the lever base.


Hide 71303C 22.INSTALL REAR SEATBACK HINGE SUB-ASSEMBLY RH

a.

Install the hinge with the bolt.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 23.INSTALL REAR SEATBACK ASSEMBLY RH

B238041E03
0.219,2.75 0.219,2.656 false 0.219,2.656 0.563,2.083 false 2.146,3.063 2.354,3.26 0.208,0.198 10 true (1) 2.229,2.531 2.438,2.729 0.208,0.198 10 true (2) 0.177,1.667 0.385,1.865 0.208,0.198 10 true (3) 0.146,2.781 0.323,2.958 0.177,0.177 10 false *1

a.

Fold down the seatback, set the seatback positioning wire on the hinge, and then temporarily install the bolt to the hinge.

Text in Illustration
*1 Positioning Wire

NOTICE:

Be careful not to damage the vehicle body.



b.

Restore the seatback to the upright position and temporarily install the seatback with the 2 bolts.


c.

Tighten the bolts in the order indicated in the illustration.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


d.

Attach the 2 claws and connect the outer belt with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 71880A 24.INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY RH

a.

for Plastic Seatback Board:

i.

Attach the 4 clips to install the carpet.


ii.

Attach the 5 claws and 2 clips to install the carpet.



b.

for Seatback Board with carpet:

Attach the 2 claws and 5 clips to install the carpet.


Hide 72996A 25.INSTALL REAR SEATBACK COVER

a.

Attach the 4 claws to install the cover.


Hide 71940A 26.INSTALL REAR SEAT HEADREST ASSEMBLY

a.

Install the headrest.


Hide 27.INSTALL REAR SEAT CUSHION ASSEMBLY RH

B240264E04
2.125,1.635 2.333,1.813 0.208,0.177 10 false (1) 1.625,1.75 1.833,1.927 0.208,0.177 10 false (2)

a.

Temporarily install the seat cushion with the 2 bolts.

NOTICE:

Be careful not to damage the vehicle body.



b.

Tighten the bolts in the order indicated in the illustration.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


c.

Lock the seat cushion.


Hide 71629A 28.INSTALL REAR SEAT CUSHION HINGE COVER RH

a.

Attach the 3 claws to install the cover.


Hide 71629 29.INSTALL REAR SEAT CUSHION HINGE COVER

a.

Attach the 3 claws to install the cover.