Home › Vehicle Interior › SEAT › REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Slide Walk-in Seat Type LH Side) › 2009.08–2015.08
RM1440E _58 Vehicle Interior _056161 SEAT _0274107 REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Slide Walk-in Seat Type LH Side) A

SEAT  REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Slide Walk-in Seat Type LH Side)  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


HINT:

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).


PROCEDURE

Hide 72173B 1.INSTALL REAR SEAT TRACK ADJUSTING HANDLE LH

B237696

a.

Install the handle.

HINT:

Make sure the handle is straight when installing it, and check that it is centered.



Hide 71016A 2.INSTALL REAR SEAT CUSHION FRAME SUB-ASSEMBLY LH

a.

Install the seat cushion frame with the 6 nuts.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)


Hide 71018 3.INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY LH

B237693E03
0.354,1.563 0.458,1.563 false 0.448,1.563 0.938,1.135 true 0.146,1.469 0.302,1.667 0.156,0.198 10 false *1

a.

Temporarily install the seatback frame with the 2 bolts and 2 "TORX" bolts.


b.

Install the bolt to the bolt hole for the outer belt.

Text in Illustration
*1 Outer Belt Installation Bolt


c.

Using a T45 "TORX" socket wrench, tighten the 2 "TORX" bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


d.

Tighten the 2 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


e.

Remove the bolt from the bolt hole for the outer belt.


Hide 72068 4.INSTALL REAR BACK LOCK CONTROL LEVER SUB-ASSEMBLY LH

a.

Install the lever with the 2 nuts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 72704B 5.INSTALL REAR NO. 2 SEAT RECLINING CONTROL CABLE

a.

Install the cable to the seat frame.


b.

Attach the 3 cable clamps and connect the cable.


Hide 72704A 6.INSTALL REAR SEAT RECLINING CONTROL CABLE

a.

Install the cable to the seat frame.


b.

Attach the 3 cable clamps and connect the cable.


c.

Install 4 new cable ties.


Hide 73187A 8.INSTALL REAR SEAT SHOULDER BELT GUIDE

a.

Attach the guide and claw to install the belt guide.


Hide 71499D 9.INSTALL REAR SEATBACK SPRING DAMPER

a.

Install the damper with the 2 nuts.


Hide 71879B 10.INSTALL REAR SEAT RECLINING COVER INNER LH

a.

Attach the guide and claw to install the cover.


Hide 73949 11.INSTALL CAP

a.

Attach the 2 claws to install the cap.


Hide 71828B 12.INSTALL REAR SEAT REAR CUSHION MOULDING LH

B237682

a.

Move the moulding in the direction of the arrow to attach the guide.


b.

Attach the 4 claws and clip to install the moulding.


Hide 71876J 13.INSTALL RECLINING ADJUSTER INSIDE COVER LH

a.

Attach the 2 claws to install the cover.


b.

Install the 2 screws.


Hide 71879A 14.INSTALL REAR SEAT INNER RECLINING COVER LH

a.

Attach the guide and install the cover with the 2 screws.


Hide 71587A 15.INSTALL REAR SEATBACK EDGE PROTECTOR

a.

Install the protector to the seatback frame.


Hide 71078S 16.INSTALL SEPARATE TYPE REAR SEATBACK COVER

B237678E01
2.158,2.519 2.388,2.712 0.230,0.193 10 *1 2.113,2.594 1.946,2.594 1.946,2.594 1.617,3.781 false

a.

Using hog ring pliers, install the seatback cover to the seatback pad with new hog rings.

Text in Illustration
*1 Hog Ring Pliers

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.




Hide 17.INSTALL SEATBACK COVER WITH PAD

a.
B237675

Connect the outer belt to the seatback cover with pad.


b.

Attach the hooks.

B453492E01
1.688,1.135 1.875,0.594 1.875,0.594 2.042,0.594 false 1.031,0.594 1.875,0.594 1.875,0.594 1.177,0.792 false 0.979,1.833 1.906,1.833 false 5.198,2.313 5.49,1.302 5.49,1.302 5.667,1.302 false 2.115,0.521 2.427,0.719 0.313,0.198 10 false *2 0.792,1.76 1.104,1.958 0.313,0.198 10 false *3 5.708,1.219 6.021,1.417 0.313,0.198 10 false *1

Text in Illustration
*1 Hog Ring Pliers
*2 Hook
*3 Hog Ring


c.

Using hog ring pliers, install the seatback cover with pad with new hog rings.


Hide 71931B 18.INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY

a.

Attach the 4 claws to install the 2 supports.


Hide 71890A 19.INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY LH

a.

Attach the 7 clips to install the carpet.


Hide 72996A 20.INSTALL REAR SEATBACK COVER

a.

Attach the 4 claws to install the cover.


Hide 73373 21.INSTALL REAR SEAT SHOULDER BELT COVER

a.

Connect the outer belt to the cover.


b.
B237669

Attach the 2 guides and 2 claws to install the cover.


Hide 73178A 22.INSTALL SEAT BELT ANCHOR COVER CAP

B237667

a.

Attach the 2 claws to install the cap.


Hide 72058A 23.INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH

a.
B165026E07
1.635,2.927 1.865,3.094 0.229,0.167 10 false (1) 1.667,2.208 1.896,2.375 0.229,0.167 10 true (2) 0.24,0.833 0.469,1 0.229,0.167 10 true (3)

Connect the cable in the order shown in the illustration to install the lever.


b.

Install the 2 screws.


Hide 72572C 24.INSTALL RECLINING ADJUSTER KNOB CAP LH

B237664

a.

Attach the guide and claw to install the cap.


Hide 73390C 25.INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY LH

B237670E06
0.25,1.969 0.323,1.969 false 0.323,1.969 0.49,2.75 false 3.198,0.156 3.125,0.156 false 3.125,0.156 2.854,0.688 false 0.052,1.885 0.208,2.063 0.156,0.177 10 false *1 3.25,0.073 3.406,0.25 0.156,0.177 10 false *1

a.

Install the inner belt and connect the center outer belt with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

NOTICE:

Do not allow the anchor part of the center outer belt and inner belt to overlap the protruding parts of the seat cushion frame.


Text in Illustration
*1 Protruding Part


Hide 72978 26.INSTALL CENTER NO. 2 SEATBACK COVER

a.

Install the cover with the 3 screws.


Hide 74633A 27.INSTALL COAT HOOK CAP

B237661

a.

Attach the guide and 2 claws to install the cap.


Hide 79873 28.INSTALL FOLD SEATBACK WIRE

a.

Attach the 2 claws to install the wire.


Hide 72663 29.INSTALL REAR NO. 1 SEAT LOCK CONTROL LEVER

B237658

a.

Install the lever as shown in the illustration.


Hide 72660F 30.INSTALL REAR SEAT LOCK ASSEMBLY LH

a.

Install the lock with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Attach the clamp to connect the wire.


Hide 79157 31.INSTALL NO. 1 SEATBACK COVER

a.
B237655

Attach the guide.


b.
B237653

Attach the 2 claws to install the cover.


Hide 71931A 32.INSTALL REAR SEAT HEADREST SUPPORT

a.

Attach the 4 claws to install the 2 supports.


Hide 72877C 33.INSTALL SEAT ARMREST COVER

a.
B237649

Install the cover to the pad.


b.
B237648

Install the cover with pad.


c.
B237646

Attach the hooks.


Hide 71087 34.INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY

a.

Attach the 5 clips to install the board.


Hide 72665B 35.INSTALL REAR SEATBACK LOCK COVER

B237643

a.

Move the cover in the direction of the arrow to attach the clip and 2 guides.


b.

Attach the claw.


Hide 72996A 36.INSTALL REAR SEATBACK COVER

a.

Attach the 4 claws to install the cover.


Hide 72806B 37.INSTALL REAR SEAT CENTER ARMREST CUP HOLDER SUB-ASSEMBLY

B237640

a.

Attach the 2 claws to install the cup holder.


b.

Install the 2 screws.


Hide 72830 38.INSTALL REAR SEAT CENTER ARMREST ASSEMBLY

a.
B237637

Install the armrest as shown in the illustration.


b.

Install the armrest support with the nut.


c.

Using a T45 "TORX" socket wrench, install the armrest and 2 bushes with the 2 "TORX" bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 71349B 39.INSTALL REAR SEATBACK STAY COVER RH

a.

Attach the guide and 3 claws to install the cover.


Hide 71369B 40.INSTALL REAR SEATBACK STAY COVER LH

a.

Attach the guide and 3 claws to install the cover.


Hide 72731 41.INSTALL REAR SEAT RECLINING BRACKET RH

a.

Using a T45 "TORX" socket wrench, install the bracket and bush with the "TORX" bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 72732 42.INSTALL REAR SEAT RECLINING BRACKET LH

a.

Using a T45 "TORX" socket wrench, install the bracket and bush with the "TORX" bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 71397A 43.INSTALL CENTER SEAT HINGE COVER

B237631

a.

Attach the 2 guides and install the cover with the clip.


Hide 71960B 44.INSTALL REAR SEAT CENTER HEADREST ASSEMBLY

a.

Install the headrest.


Hide 45.INSTALL CENTER SEATBACK ASSEMBLY

a.

Install the center seatback with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 71647 46.INSTALL REAR SEAT CUSHION EDGE PROTECTOR

a.

Install the protector to the cushion spring.


Hide 71076S 47.INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER

B237628E01
2.332,2.309 2.562,2.502 0.230,0.193 10 *1 2.286,2.384 2.12,2.384 2.12,2.384 1.622,3.776 false

a.

Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.

Text in Illustration
*1 Hog Ring Pliers

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.




Hide 71696 48.INSTALL REAR NO. 2 SEAT PROTECTOR

a.

Install the 2 protectors to the cushion pad.


Hide 49.INSTALL SEAT CUSHION COVER WITH PAD

a.
B237625

Attach the hook.


b.
B237623

Attach the hooks to install the seat cushion cover with pad.


Hide 72616A 50.INSTALL REAR SEATBACK LOCK STRIKER COVER LH

a.

Attach the 3 clips to install the cover.


Hide 71826B 51.INSTALL REAR SEAT CUSHION MOULDING LH

B237620

a.

Move the moulding in the direction of the arrow to attach the guide.


b.

Attach the 3 claws and clip to install the moulding.


Hide 71395B 52.INSTALL CENTER SEAT HINGE COVER RH

B237618

a.

Attach the 2 guides and install the cover with the clip.


Hide 72526A 53.INSTALL RECLINING ADJUSTER RELEASE HANDLE LH

a.

Install the handle with the 3 screws.


Hide 71846A 54.INSTALL REAR SEAT UPPER RECLINING COVER LH

B237786

a.

Attach the 3 claws to install the cover.