Home › Vehicle Interior › SEAT › REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Slide Walk-in Seat Type LH Side) › from 2015.08
RM1440E _58 Vehicle Interior _056161 SEAT _0274107 REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Slide Walk-in Seat Type LH Side) A

SEAT  REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Slide Walk-in Seat Type LH Side)  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


HINT:

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).


PROCEDURE

Hide 72173B 1.INSTALL REAR SEAT TRACK ADJUSTING HANDLE LH

B237696

a.

Install the rear seat track adjusting handle LH.

HINT:

Make sure the handle is straight when installing it, and check that it is centered.



Hide 71016A 2.INSTALL REAR SEAT CUSHION FRAME SUB-ASSEMBLY LH

a.

Install the rear seat cushion frame sub-assembly LH with the 6 nuts.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)


Hide 71018 3.INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY LH

B237693E03
0.354,1.563 0.458,1.563 false 0.448,1.563 0.938,1.135 true 0.146,1.469 0.302,1.667 0.156,0.198 10 false *1

a.

Temporarily install the rear seatback frame sub-assembly LH with the 2 bolts and 2 "TORX" bolts.


b.

Install the bolt to the bolt hole for the rear No. 1 seat inner belt assembly LH.

Text in Illustration
*1 Rear No. 1 Seat Inner Belt Assembly LH Installation Bolt


c.

Using a T45 "TORX" socket wrench, tighten the 2 "TORX" bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


d.

Tighten the 2 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


e.

Remove the bolt from the bolt hole for the rear No. 1 seat inner belt assembly LH.


Hide 4.INSTALL REAR SEAT RECLINING INNER PROTECTOR RH

a.

Attach the claw and install the rear seat reclining inner protector RH.


Hide 72068 5.INSTALL REAR BACK LOCK CONTROL LEVER SUB-ASSEMBLY LH

a.

Install the rear back lock control lever sub-assembly with the 2 nuts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 6.INSTALL REAR SEAT RECLINING INNERPROTECTOR

a.

Attach the claw to install the rear seat reclining inner protector.


Hide 72704B 7.INSTALL REAR NO. 2 SEAT RECLINING CONTROL CABLE

a.

Install the rear No. 2 seat reclining control cable to the rear seat frame.


b.

Attach the 3 cable clamps and connect the rear No. 2 seat reclining control cable.


Hide 72704A 8.INSTALL REAR SEAT RECLINING CONTROL CABLE

a.

Install the rear seat reclining control cable to the rear seat frame.


b.

Attach the 3 cable clamps and connect the rear seat reclining control cable.


c.

Install 4 new cable ties.


Hide 73187A 10.INSTALL REAR SEAT SHOULDER BELT GUIDE

a.

Attach the guide and claw to install the rear seat shoulder belt guide.


Hide 71499D 11.INSTALL REAR SEATBACK SPRING DAMPER

a.

Install the rear seatback spring damper with the 2 nuts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide 71879B 12.INSTALL REAR SEAT RECLINING COVER INNER LH

a.

Attach the guide and claw to install the rear seat reclining cover inner LH.


Hide 73949 13.INSTALL CAP

a.

Attach the 2 claws to install the cap.


Hide 71828B 14.INSTALL REAR SEAT REAR CUSHION MOULDING LH

B237682

a.

Move the rear seat rear cushion moulding LH in the direction of the arrow to attach the guide.


b.

Attach the 4 claws and clip to install the rear seat rear cushion moulding LH.


Hide 71876J 15.INSTALL RECLINING ADJUSTER INSIDE COVER LH

a.

Attach the 2 claws to install the reclining adjuster inside cover LH.


b.

Install the 2 screws.


Hide 71879A 16.INSTALL REAR SEAT INNER RECLINING COVER LH

a.

Attach the guide and install the rear seat inner reclining cover LH with the 2 screws.


Hide 71587A 17.INSTALL REAR SEATBACK EDGE PROTECTOR

a.

Install the rear seatback edge protector to the rear seatback frame sub-assembly LH.


Hide 71078S 18.INSTALL SEPARATE TYPE REAR SEATBACK COVER

B237678E01
2.158,2.519 2.388,2.712 0.230,0.193 10 *1 2.113,2.594 1.946,2.594 1.946,2.594 1.617,3.781 false

a.

Using hog ring pliers, install the separate type rear seatback cover to the separate type rear seatback pad with new hog rings.

Text in Illustration
*1 Hog Ring Pliers

NOTICE:
·

Be careful not to damage the separate type rear seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover.




Hide 19.INSTALL SEATBACK COVER WITH PAD

a.
B237675

Connect the No. 1 seat 3 point type belt assembly LH to the seatback cover with pad.


b.

Attach the hooks.

B453492E02
1.667,1.135 1.875,0.594 1.875,0.594 2.042,0.594 false 1.031,0.594 1.875,0.594 1.875,0.594 1.177,0.781 false 0.979,1.833 1.906,1.833 false 5.198,2.302 5.49,1.292 5.49,1.292 5.667,1.292 false 2.115,0.521 2.427,0.719 0.313,0.198 10 false *2 0.792,1.76 1.104,1.958 0.313,0.198 10 false *3 5.708,1.219 6.021,1.417 0.313,0.198 10 false *1

Text in Illustration
*1 Hog Ring Pliers
*2 Hook
*3 Hog Ring


c.

Using hog ring pliers, install the seatback cover with pad with new hog rings.


Hide 71931B 20.INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY

a.

Attach the 4 claws to install the 2 rear No. 1 seat headrest support assemblies.


Hide 71890A 21.INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY LH

a.

Attach the 7 clips to install the rear seatback board carpet assembly LH.


Hide 72996A 22.INSTALL REAR SEATBACK COVER

a.

Attach the 4 claws to install the rear seatback cover.


Hide 73373 23.INSTALL REAR SEAT SHOULDER BELT COVER

a.

Connect the No. 1 seat 3 point type belt assembly LH to the rear seat shoulder belt cover.


b.
B237669

Move the rear seat shoulder belt cover in the direction of the arrow to attach the 2 guides.


c.

Attach the 2 claws to install the rear seat shoulder belt cover.


Hide 73178A 24.INSTALL SEAT BELT ANCHOR COVER CAP

B237667

a.

Attach the 2 claws to install the seat belt anchor cover cap.


Hide 72058A 25.INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH

a.
B165026E07
1.635,2.927 1.865,3.094 0.229,0.167 10 false (1) 1.667,2.208 1.896,2.375 0.229,0.167 10 true (2) 0.24,0.833 0.469,1 0.229,0.167 10 true (3)

Connect the rear No. 2 seat reclining control cable in the order shown in the illustration to install the rear seat lock control lever sub-assembly LH.


b.

Install the 2 screws.


Hide 72572C 26.INSTALL RECLINING ADJUSTER KNOB CAP LH

B237664

a.

Attach the guide and claw to install the reclining adjuster knob cap LH.


Hide 73390C 27.INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY LH

B237670E07
0.25,3.167 0.5,2.792 true 3.25,0.188 2.875,0.583 true 0.083,3.115 0.24,3.302 0.156,0.188 10 false *1 3.229,0.052 3.385,0.229 0.156,0.177 10 false *1

a.

Install the rear No. 1 seat inner belt assembly LH and connect the No. 1 seat 3 point type belt assembly LH with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

NOTICE:

Do not allow the anchor part of the No. 1 seat 3 point type belt assembly LH and rear No. 1 seat inner belt assembly LH to overlap the protruding parts of the rear seat cushion frame sub-assembly LH.


Text in Illustration
*1 Protruding Part


Hide 72978 28.INSTALL CENTER NO. 2 SEATBACK COVER

a.

Install the center No. 2 seatback cover with the 3 screws.


Hide 74633A 29.INSTALL COAT HOOK CAP

B237661

a.

Attach the guide and 2 claws to install the coat hook cap.


Hide 79873 30.INSTALL FOLD SEATBACK WIRE

a.

Attach the 2 claws to install the fold seatback wire.


Hide 72663 31.INSTALL REAR NO. 1 SEAT LOCK CONTROL LEVER

B237658

a.

Install the rear No. 1seat lock control lever as shown in the illustration.


Hide 72660F 32.INSTALL REAR SEAT LOCK ASSEMBLY LH

a.

Install the rear seat lock assembly LH with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Attach the clamp to connect the fold seatback wire.


Hide 79157 33.INSTALL NO. 1 SEATBACK COVER

a.
B237655

Attach the guide.


b.
B237653

Attach the 2 claws to install the No. 1 seatback cover.


Hide 71931A 34.INSTALL REAR SEAT HEADREST SUPPORT

a.

Attach the 4 claws to install the 2 rear seat headrest supports.


Hide 72877C 35.INSTALL SEAT ARMREST COVER

a.
B237649

Install the seat armrest cover to the center No. 1 seat cushion pad.


b.
B237648

Install the seat armrest cover with pad.


c.
B237646

Attach the hooks.


Hide 71087 36.INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY

a.

Attach the 5 clips to install the rear seatback board sub-assembly.


Hide 72665B 37.INSTALL REAR SEATBACK LOCK COVER

B237643

a.

Move the rear seatback lock cover in the direction of the arrow to attach the clip and 2 guides.


b.

Attach the claw.


Hide 72996A 38.INSTALL REAR SEATBACK COVER

a.

Attach the 4 claws to install the rear seatback cover.


Hide 72806B 39.INSTALL REAR SEAT CENTER ARMREST CUP HOLDER SUB-ASSEMBLY

B237640

a.

Attach the 2 claws to install the rear seat center armrest cup holder sub-assembly.


b.

Install the 2 screws.


Hide 72830 40.INSTALL REAR SEAT CENTER ARMREST ASSEMBLY

a.
B237637

Install the rear seat center armrest assembly as shown in the illustration.


b.

Install the rear center seat armrest support LH with the nut.


c.

Install the wave washer, washer and 2 bushes.


d.

Using a T45 "TORX" socket wrench, install the rear seat center armrest assembly with the 2 "TORX" bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 71369B 41.INSTALL REAR SEATBACK STAY COVER LH

a.

Attach the guide and 3 claws to install the rear seatback stay cover LH.


Hide 71349B 42.INSTALL REAR SEATBACK STAY COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 72732 43.INSTALL REAR SEAT RECLINING BRACKET LH

a.

Using a T45 "TORX" socket wrench, install the rear seat reclining bracket LH and bush with the "TORX" bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 72731 44.INSTALL REAR SEAT RECLINING BRACKET RH

HINT:

Use the same procedure as for the LH side.


Hide 71397A 45.INSTALL CENTER SEAT HINGE COVER

B237631

a.

Move the center seat hinge cover in the direction of the arrow to attach the 2 guides.


b.

Install the center seat hinge cover with the clip.


Hide 71960B 46.INSTALL REAR SEAT CENTER HEADREST ASSEMBLY

a.

Install the rear seat center headrest assembly.


Hide 47.INSTALL CENTER SEATBACK ASSEMBLY

a.

Install the center seatback assembly with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 71647 48.INSTALL REAR SEAT CUSHION EDGE PROTECTOR

a.

Install the rear seat cushion edge protector to the rear seat cushion frame sub-assembly LH.


Hide 71076S 49.INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER

B237628E01
2.332,2.309 2.562,2.502 0.230,0.193 10 *1 2.286,2.384 2.12,2.384 2.12,2.384 1.622,3.776 false

a.

Using hog ring pliers, install the separate type rear seat cushion cover to the separate type rear seat cushion pad with new hog rings.

Text in Illustration
*1 Hog Ring Pliers

NOTICE:
·

Be careful not to damage the separate type rear seat cushion cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seat cushion cover.




Hide 71696 50.INSTALL REAR NO. 2 SEAT PROTECTOR

a.

Install the 2 rear No. 2 seat protectors to the separate type rear seat cushion pad.


Hide 51.INSTALL SEAT CUSHION COVER WITH PAD

a.
B237625

Attach the hook.


b.
B237623

Attach the hooks to install the seat cushion cover with pad.


Hide 72616A 52.INSTALL REAR SEATBACK LOCK STRIKER COVER LH

a.

Attach the 3 clips to install the rear seatback lock striker cover LH.


Hide 71826B 53.INSTALL REAR SEAT CUSHION MOULDING LH

B237620

a.

Move the rear seat cushion moulding LH in the direction of the arrow to attach the guide.


b.

Attach the 3 claws and clip to install the rear seat cushion moulding LH.


Hide 71395B 54.INSTALL CENTER SEAT HINGE COVER RH

B237618

a.

Move the center seat hinge cover RH in the direction of the arrow to attach the 2 guides.


b.

Install the center seat hinge cover RH with the clip.


Hide 72526A 55.INSTALL RECLINING ADJUSTER RELEASE HANDLE LH

a.

Install the reclining adjuster release handle LH with the 3 screws.


Hide 71846A 56.INSTALL REAR SEAT UPPER RECLINING COVER LH

B237786

a.

Attach the 3 claws to install the rear seat upper reclining cover LH.