Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) › from 2013.08
RM1440E _58 Vehicle Interior _056161 SEAT _0274116 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) U

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  TERMINALS OF ECU  


CHECK FRONT POWER SEAT SWITCH LH


U149699E03
4.125,0.333 4.385,0.49 0.26,0.156 10 false b19 3.125,0.333 3.385,0.49 0.26,0.156 10 false b18

a.

Disconnect the b18 and b19 connectors from the front power seat switch LH.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
b18-2 (GND1) - Body ground W-B - Body ground Ground Always Below 1 Ω
b18-7 (+B1) - b18-2 (GND1) W - W-B Power source Always 11 to 14 V
b19-12 (SYSB) - b18-2 (GND1) P - W-B System power source Always 11 to 14 V

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the b18 and b19 switch connectors.


d.

Measure the voltage and registance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
b18-3 (SLD+) - b18-2 (GND1) L - W-B Sliding motor signal (forward) Slide switch off Below 1 V
Slide switch on (Forward) 11 to 14 V
b18-4 (SLD-) - b18-2 (GND1) GR - W-B Sliding motor signal (rearward) Slide switch off Below 1 V
Slide switch on (Rearward) 11 to 14 V
b18-5 (FRV-) - b18-2 (GND1) R - W-B Front vertical motor signal (downward) Front vertical switch off Below 1 V
Front vertical switch on (Downward) 11 to 14 V
b18-6 (+B2) - b18-1 (GND2) SB - W-B Power source Always 11 to 14 V
b18-8 (FRV+) - b18-2 (GND1) B - W-B Front vertical motor signal (upward) Front vertical switch off Below 1 V
Front vertical switch on (Upward) 11 to 14 V
b18-9 (RCL+) - b18-2 (GND1) P - W-B Reclining motor signal (forward) Reclining switch off Below 1 V
Reclining switch on (Forward) 11 to 14 V
b18-11 (RCL-) - b18-2 (GND1) LG - W-B Reclining motor signal (rearward) Reclining switch off Below 1 V
Reclining switch on (Rearward) 11 to 14 V
b18-10 (LFT+) - b18-2 (GND1) V - W-B Lifter motor signal (upward) Lifter switch off Below 1 V
Lifter switch on (Upward) 11 to 14 V
b18-12 (LFT-) - b18-2 (GND1) G - W-B Lifter motor signal (downward) Lifter switch off Below 1 V
Lifter switch on (Downward) 11 to 14 V
b19-1 (SGND) - b18-2 (GND1) BR - W-B Ground Always Below 1 Ω
b19-3 (SSFV) - b19-1 (SGND) R - BR Front vertical position signal Front vertical function operating 4.5 to 4.8 V
b19-4 (SSRL) - b19-1 (SGND) P - BR Lifter position signal Lifter function operating 4.5 to 4.8 V
b19-5 (SSRS) - b19-1 (SGND) G- BR Slide position signal Slide function operating 4.5 to 4.8 V
b19-11 (SSRR) - b19-1 (SGND) V - BR Reclining position signal Reclining function operating 4.5 to 4.8 V

If the result is not as specified, the front power seat switch LH may have a malfunction.



CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


U149747E03
1.625,1.521 1.823,1.281 1.823,1.281 1.906,1.281 true 1.625,1.844 1.823,1.688 1.823,1.688 1.906,1.688 true 1.625,2.156 1.823,2.354 1.823,2.354 1.906,2.354 true 0.906,1.583 1.115,1.74 0.208,0.156 10 false 2F 1.094,3.875 1.375,4.031 0.281,0.156 10 false F10 0.917,2.208 1.125,2.365 0.208,0.156 10 false 2D 5.854,1.542 6.063,1.698 0.208,0.156 10 false 2B 5.854,2.219 6.063,2.375 0.208,0.156 10 false 2C 1.073,2.76 1.281,2.917 0.208,0.156 10 false 2E 3.75,1.344 3.865,1.49 0.115,0.146 10 false A 1.938,1.208 2.208,1.354 0.271,0.146 10 false F8 1.927,1.615 2.198,1.76 0.271,0.146 10 false F9 1.927,2.292 2.198,2.438 0.271,0.146 10 false F10 3.635,3.875 3.917,4.031 0.281,0.156 10 false F9 1.135,5.188 1.354,5.344 0.219,0.156 10 false 2F 1.885,6.417 2.104,6.573 0.219,0.156 10 false 2B 4.938,6.417 5.156,6.573 0.219,0.156 10 false 2C 3.51,7.677 3.646,7.833 0.135,0.156 10 false A 3.948,5.188 4.146,5.344 0.198,0.156 10 false 2D 5.896,5.188 6.094,5.344 0.198,0.156 10 false 2E 5.927,3.875 6.208,4.031 0.281,0.156 10 false F8

a.

Remove the main body ECU (multiplex network body ECU) (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A-30 (BECU) - Body ground - Power source Always 11 to 14 V
A-32 (IG) - Body ground - Power source (IG) Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
A-11 (GND1) - Body ground - Ground Always Below 1 Ω
F10-3 (GND2) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.