Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) › from 2013.08
RM1440E _58 Vehicle Interior _056161 SEAT _0274116 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) J

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  Power Seat Position is not Memorized  


DESCRIPTION

When the seat memory SET switch and a memory switch (M1 or M2) are pressed simultaneously, the main body ECU commands the position control ECU through CAN communication to record the value of each position sensor.

WIRING DIAGRAM

B358390E03
0.854,3.333 2.531,3.698 1.677,0.365 10 false :CAN Communication Line 3.875,0.938 4.146,1.094 0.271,0.156 10 false M1 3.875,1.333 4.156,1.49 0.281,0.156 10 false M2 3.875,1.729 4.156,1.885 0.281,0.156 10 false MM 5.677,0.927 5.948,1.083 0.271,0.156 10 false M1 5.677,1.323 5.958,1.479 0.281,0.156 10 false M2 5.677,1.708 6.021,1.865 0.344,0.156 10 false MRY 5.677,2.115 5.958,2.271 0.281,0.156 10 false E 0.677,2.125 2.458,2.5 1.781,0.375 10 false Front Power Seat Switch LH 2.833,2.646 4.01,2.865 1.177,0.219 10 false Main Body ECU 5.49,2.635 6.833,3.01 1.344,0.375 10 false Seat Memory Switch 5.5,2.469 5.771,2.635 0.271,0.167 10 false h3 2.844,2.469 3.115,2.635 0.271,0.167 10 false F9 4.198,0.833 4.396,0.99 0.198,0.156 10 false 23 4.198,1.24 4.396,1.396 0.198,0.156 10 false 6 4.198,1.604 4.396,1.76 0.198,0.156 10 false 12 5.521,0.833 5.719,0.99 0.198,0.156 10 false 3 5.521,1.219 5.719,1.375 0.198,0.156 10 false 4 5.521,1.604 5.719,1.76 0.198,0.156 10 false 2 5.521,2 5.719,2.156 0.198,0.156 10 false 1 2.802,2.833 4.729,3.031 1.927,0.198 10 false (Multiplex Network Body ECU)

CAUTION / NOTICE / HINT

NOTICE:

The front power seat control system (w/ Memory) uses the CAN communication system. First, confirm that there are no malfunctions in the can communication system by checking the communication function of the CAN communication system (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).


PROCEDURE

1.CHECK FRONT POWER SEAT CONTROL FUNCTION
a.

Check that each function of the power seat operates normally by using the front power seat switches (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK).

OK:

Each function of power seat operates normally by using seat switches.




OK

2.READ VALUE USING GTS (SEAT POSITION MEMORY)

NG

2.READ VALUE USING GTS (SEAT POSITION MEMORY)
a.

Use the seat memory switch to record the seat position (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK).

NOTICE:
·

The seat position will not be recorded if the SET switch and both memory switches are pressed simultaneously.

·

If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.




b.

Using the GTS, read the Data List (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>DATA LIST / ACTIVE TEST).

Driver Seat
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Seat Memory No1 Seat position memorized with M1 switch / Mem or Not Mem Mem: Memorized
Not Mem: Not memorized
-
Seat Memory No2 Seat position memorized with M2 switch / Mem or Not Mem Mem: Memorized
Not Mem: Not memorized
-

OK:

"Mem" is displayed on the tester.




OK

NG

3.INSPECT SEAT MEMORY SWITCH
3.INSPECT SEAT MEMORY SWITCH
a.

Remove the seat memory switch (See page Vehicle Interior>SEAT>SEAT MEMORY SWITCH>REMOVAL).


b.

Inspect the seat memory switch (See page Vehicle Interior>SEAT>SEAT MEMORY SWITCH>INSPECTION).



OK

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - SEAT MEMORY SWITCH)

NG

REPLACE SEAT MEMORY SWITCH

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - SEAT MEMORY SWITCH)
a.

Disconnect the F9 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the h3 seat memory switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F9-23 (M1) - h3-3 (M1) Always Below 1 Ω
F9-6 (M2) - h3-4 (M2) Always Below 1 Ω
F9-12 (MM) - h3-2 (MRY) Always Below 1 Ω
F9-23 (M1) - Body ground Always 10 kΩ or higher
F9-6 (M2) - Body ground Always 10 kΩ or higher
F9-12 (MM) - Body ground Always 10 kΩ or higher




OK

5.REPLACE FRONT POWER SEAT SWITCH LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE FRONT POWER SEAT SWITCH LH
a.

Replace the front power seat switch LH (See page Vehicle Interior>SEAT>POWER SEAT SWITCH>REMOVAL).


b.

Perform the memory operation (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK).

OK:

Memory operation is normally.




OK

END (FRONT POWER SEAT SWITCH LH WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)