Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) › from 2013.08
RM1440E _58 Vehicle Interior _056161 SEAT _0274116 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) C

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  B2650  Slide Sensor Malfunction  


DESCRIPTION

When the front power seat switch LH does not receive a sensor signal despite forward or backward movement of the seat by power seat motor operation, this DTC is stored.

DTC Code DTC Detection Condition Trouble Area
B2650 The forward and backward lock detection position of the sensor is the same.
·

Front power seat switch LH

·

Separate type front seat cushion spring assembly LH (Slide motor)

·

Harness or connector



WIRING DIAGRAM

B357484E06
1.792,1 2.135,1.156 0.344,0.156 10 false FWD 1.719,1.5 2.125,1.667 0.406,0.167 10 false BACK 1.865,2.01 2.125,2.167 0.26,0.156 10 false O/P 1.802,2.51 2.135,2.667 0.333,0.156 10 false GND 2.229,0.865 2.333,1.021 0.104,0.156 10 false 4 2.229,1.365 2.333,1.521 0.104,0.156 10 false 1 2.229,1.875 2.333,2.031 0.104,0.156 10 false 2 2.229,2.385 2.333,2.542 0.104,0.156 10 false 3 5.146,1 5.542,1.156 0.396,0.156 10 false SLD+ 5.156,1.5 5.51,1.667 0.354,0.167 10 false SLD- 5.156,2.01 5.594,2.167 0.438,0.156 10 false SSRS 5.156,2.51 5.594,2.667 0.438,0.156 10 false SGND 4.885,0.802 4.99,0.958 0.104,0.156 10 false 3 4.885,1.302 4.99,1.458 0.104,0.156 10 false 4 4.885,1.813 4.99,1.969 0.104,0.156 10 false 5 4.885,2.323 4.99,2.479 0.104,0.156 10 false 1 1.344,2.865 1.604,3.031 0.26,0.167 10 false b15 1.344,3.042 2.083,3.198 0.74,0.156 10 false Slide Motor 0.906,3.635 2.771,3.979 1.865,0.344 10 false Separate Type Front Seat Cushion Spring Assembly LH 4.781,3.635 6.583,3.792 1.802,0.156 10 false Front Power Seat Switch LH 4.823,1 5.073,1.156 0.25,0.156 10 false b18 4.823,1.5 5.104,1.656 0.281,0.156 10 false b18 4.823,2.01 5.104,2.167 0.281,0.156 10 false b19 4.823,2.521 5.104,2.677 0.281,0.156 10 false b19

PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (POWER SEAT MOTOR FUNCTION)
a.

Select the Active Test, use the GTS to generate a control command, and then check the power seat motor function (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>DATA LIST / ACTIVE TEST).

Driver Seat
Tester Display Test Part Control Range Diagnostic Note
Seat Slide Operation Seat sliding operation Front / OFF / Rear -

OK:

Motor operates normally.




OK

2.CHECK FRONT POWER SEAT SWITCH LH (SLIDE MOTOR CIRCUIT)

NG

5.INSPECT SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY LH (SLIDE MOTOR)
2.CHECK FRONT POWER SEAT SWITCH LH (SLIDE MOTOR CIRCUIT)
a.
U149737E02
1.583,1.354 1.375,1.677 1.375,1.677 1.375,1.802 false 1.833,1.354 2.042,1.677 2.042,1.677 2.042,1.802 false 0.135,0.104 0.313,0.271 0.177,0.167 10 false *a 1.219,1.813 1.542,1.969 0.323,0.156 10 false O/P 1.875,1.813 2.198,1.969 0.323,0.156 10 false GND 0.313,1.167 0.583,1.323 0.271,0.156 10 false b15

Disconnect the b15 slide motor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
b15-2 (O/P) - b15-3 (GND) Sliding switch on 4.8 to 5.1 V


Text in Illustration
*a Front view of wire harness connector
(to Separate Type Front Seat Cushion Spring Assembly LH [Slide Motor])



OK

3.CHECK SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY LH (SLIDE MOTOR)

NG

4.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - SLIDE MOTOR)
3.CHECK SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY LH (SLIDE MOTOR)
a.
U149846E02
1.844,1.469 1.844,1.875 false 0.156,0.188 0.333,0.354 0.177,0.167 10 false *a 1.698,1.896 2.021,2.052 0.323,0.156 10 false O/P 0.323,1.24 0.594,1.396 0.271,0.156 10 false b15

Connect the b15 slide motor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
b15-2 (O/P) - Body ground Sliding switch on 4.5 to 4.8 V


Text in Illustration
*a Component with harness connected
(Separate Type Front Seat Cushion Spring Assembly LH [Slide Motor])



OK

REPLACE FRONT POWER SEAT SWITCH LH

NG

REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY LH (SLIDE MOTOR)

4.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - SLIDE MOTOR)
a.

Disconnect the b19 front power seat switch LH connector.


b.

Disconnect the b15 slide motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
b19-5 (SSRS) - b15-2 (O/P) Always Below 1 Ω
b19-1 (SGND) - b15-3 (GND) Always Below 1 Ω
b19-5 (SSRS) - Body ground Always 10 kΩ or higher
b19-1 (SGND) - Body ground Always 10 kΩ or higher




OK

REPLACE FRONT POWER SEAT SWITCH LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY LH (SLIDE MOTOR)
a.
B238714E31
1.458,1.094 1.26,1.365 1.26,1.365 1.26,1.5 false 2,1.094 2.198,1.365 2.198,1.365 2.198,1.5 false 1.063,1.521 1.406,1.677 0.344,0.156 10 false FWD 0.135,0.073 0.479,0.229 0.344,0.156 10 false *a 1.979,1.521 2.396,1.688 0.417,0.167 10 false BACK

Remove the separate type front seat cushion spring assembly LH (slide motor) (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>DISASSEMBLY).


b.

Disconnect the b15 slide motor connector.


c.

Check if the seat cushion spring moves smoothly when the battery is connected to the slide motor connector terminals.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 4 (FWD)
Battery negative (-) → 1 (BACK)
Front seat cushion spring assembly LH moves forward
Battery positive (+) → 1 (BACK)
Battery negative (-) → 4 (FWD)
Front seat cushion spring assembly LH moves backward


Text in Illustration
*a Component without harness connected
(Separate Type Front Seat Cushion Spring Assembly LH [Slide Motor])



OK

6.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH - SLIDE MOTOR)

NG

REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY LH (SLIDE MOTOR)

6.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH - SLIDE MOTOR)
a.

Disconnect the b18 front power seat switch LH connector.


b.

Disconnect the b15 slide motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
b18-3 (SLD+) - b15-4 (FWD) Always Below 1 Ω
b18-4 (SLD-) - b15-1 (BACK) Always Below 1 Ω
b18-3 (SLD+) - Body ground Always 10 kΩ or higher
b18-4 (SLD-) - Body ground Always 10 kΩ or higher




OK

REPLACE FRONT POWER SEAT SWITCH LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR