Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) › from 2013.08
RM1440E _58 Vehicle Interior _056161 SEAT _0274116 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) C

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  B2651  Reclining Sensor Malfunction  


DESCRIPTION

When the front power seat switch LH does not receive a sensor signal despite forward or backward movement of the seatback by power seat motor operation, this DTC is stored.

DTC Code DTC Detection Condition Trouble Area
B2651 The forward and backward lock detection position of the sensor is the same.
·

Front power seat switch LH

·

Separate type front seatback spring assembly LH (Reclining motor)

·

Harness or connector



WIRING DIAGRAM

B357484E07
1.802,0.979 2.146,1.135 0.344,0.156 10 false FWD 1.729,1.479 2.135,1.646 0.406,0.167 10 false BACK 1.875,1.99 2.135,2.146 0.26,0.156 10 false O/P 1.813,2.49 2.146,2.646 0.333,0.156 10 false GND 2.24,0.865 2.49,1.021 0.25,0.156 10 false 1 2.24,1.365 2.479,1.521 0.24,0.156 10 false 4 2.24,1.875 2.344,2.031 0.104,0.156 10 false 2 2.24,2.385 2.344,2.542 0.104,0.156 10 false 3 5.167,1 5.563,1.156 0.396,0.156 10 false RCL+ 5.167,1.5 5.521,1.667 0.354,0.167 10 false RCL- 5.167,2.01 5.604,2.167 0.438,0.156 10 false SSRR 5.167,2.521 5.604,2.677 0.438,0.156 10 false SGND 4.896,0.802 5,0.958 0.104,0.156 10 false 9 4.854,1.313 5.031,1.469 0.177,0.156 10 false 11 4.854,1.813 5.031,1.969 0.177,0.156 10 false 11 4.896,2.323 5,2.479 0.104,0.156 10 false 1 1.281,2.875 1.469,3.063 0.188,0.188 10 false d4 1.281,3.021 2.292,3.25 1.01,0.229 10 false Reclining Motor 0.875,3.656 2.802,4 1.927,0.344 10 false Separate Type Front Seatback Spring Assembly LH 4.771,3.635 6.563,3.792 1.792,0.156 10 false Front Power Seat Switch LH 4.813,1 5.063,1.156 0.25,0.156 10 false b18 4.823,1.5 5.073,1.656 0.25,0.156 10 false b18 4.823,2.01 5.073,2.167 0.25,0.156 10 false b19 4.823,2.521 5.073,2.677 0.25,0.156 10 false b19

PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (POWER SEAT MOTOR FUNCTION)
a.

Select the Active Test, use the GTS to generate a control command, and then check the power seat motor function (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>DATA LIST / ACTIVE TEST).

Driver Seat
Tester Display Test Part Control Ranger Diagnostic Note
Seat Reclining Seat reclining operation Front / OFF / Rear -

OK:

Motor operates normally.




OK

2.CHECK FRONT POWER SEAT SWITCH LH (RECLINING MOTOR CIRCUIT)

NG

5.INSPECT SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY LH (RECLINING MOTOR)
2.CHECK FRONT POWER SEAT SWITCH LH (RECLINING MOTOR CIRCUIT)
a.
U180722E02
1.583,1.354 1.375,1.677 1.375,1.677 1.375,1.802 false 1.833,1.354 2.042,1.677 2.042,1.677 2.042,1.802 false 0.135,0.104 0.313,0.271 0.177,0.167 10 false *a 1.219,1.813 1.49,1.969 0.271,0.156 10 false O/P 1.875,1.813 2.198,1.969 0.323,0.156 10 false GND 0.354,1.104 0.531,1.26 0.177,0.156 10 false d4

Disconnect the d4 reclining motor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
d4-2 (O/P) - d4-3 (GND) Reclining switch on 4.8 to 5.1 V


Text in Illustration
*a Front view of wire harness connector
(to Separate Type Front Seatback Spring Assembly LH [Reclining Motor])



OK

3.CHECK SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY LH (RECLINING MOTOR)

NG

4.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - RECLINING MOTOR)
3.CHECK SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY LH (RECLINING MOTOR)
a.
U180806E01
0.153,0.186 0.326,0.355 0.173,0.169 10 *a 1.694,1.896 2.021,2.049 0.328,0.152 10 O/P 1.848,1.471 1.848,1.879 false 0.355,1.232 0.625,1.389 0.270,0.157 10 d4

Connect the d4 reclining motor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
d4-2 (O/P) - Body ground Reclining switch on 4.5 to 4.8 V


Text in Illustration
*a Component with harness connected
(Separate Type Front Seatback Spring Assembly LH [Reclining Motor])



OK

REPLACE FRONT POWER SEAT SWITCH LH

NG

REPLACE SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY LH (RECLINING MOTOR)

4.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - RECLINING MOTOR)
a.

Disconnect the b19 front power seat switch LH connector.


b.

Disconnect the d4 reclining motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
b19-11 (SSRR) - d4-2 (O/P) Always Below 1 Ω
b19-1 (SGND) - d4-3 (GND) Always Below 1 Ω
b19-11 (SSRR) - Body ground Always 10 kΩ or higher
b19-1 (SGND) - Body ground Always 10 kΩ or higher




OK

REPLACE FRONT POWER SEAT SWITCH LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY LH (RECLINING MOTOR)
a.
B238256E21
1.99,1.292 1.99,1.625 false 1.448,1.292 1.448,1.625 false 1.833,1.667 2.302,1.823 0.469,0.156 10 false FWD 1.26,1.656 1.667,1.854 0.406,0.198 10 false BACK 0.125,0.083 0.531,0.281 0.406,0.198 10 false *a

Remove the front seatback board sub-assembly (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>DISASSEMBLY).


b.

Disconnect the b5 reclining motor connector.


c.

Check if the seatback moves smoothly when the battery is connected to the reclining motor connector terminals.

OK:
Measurement Condition Operational Direction
Battery positive (+) → 1 (FWD)
Battery negative (-) → 4 (BACK)
Seatback moves forward
Battery positive (+) → 4 (BACK)
Battery negative (-) → 1 (FWD)
Seatback moves backward


Text in Illustration
*a Component without harness connected
(Separate Type Front Seatback Spring Assembly LH [Reclining Motor])



OK

6.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH - RECLINING MOTOR)

NG

REPLACE SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY LH (RECLINING MOTOR)

6.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH - RECLINING MOTOR)
a.

Disconnect the b18 front power seat switch LH connector.


b.

Disconnect the d4 reclining motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
b18-9 (RCL+) - d4-1 (FWD) Always Below 1 Ω
b18-11 (RCL-) - d4-4 (BACK) Always Below 1 Ω
b18-9 (RCL+) - Body ground Always 10 kΩ or higher
b18-11 (RCL-) - Body ground Always 10 kΩ or higher




OK

REPLACE FRONT POWER SEAT SWITCH LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR