Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) › from 2013.08
RM1440E _58 Vehicle Interior _056161 SEAT _0274116 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) C

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  B2652  Front Vertical Sensor Malfunction  


DESCRIPTION

When the front power seat switch LH does not receive a sensor signal despite upward or downward movement of the front of the seat cushion by power seat motor operation, this DTC is stored.

DTC Code DTC Detection Condition Trouble Area
B2652 The upward and downward lock detection position of the sensor is the same.
·

Front power seat switch LH

·

Separate type front seat cushion Spring assembly LH (Front vertical motor)

·

Harness or connector



WIRING DIAGRAM

B357484E08
1.927,0.979 2.146,1.135 0.219,0.156 10 false UP 1.677,1.479 2.135,1.646 0.458,0.167 10 false DOWN 1.875,1.99 2.146,2.146 0.271,0.156 10 false O/P 1.813,2.5 2.146,2.656 0.333,0.156 10 false GND 2.24,0.865 2.49,1.021 0.25,0.156 10 false 4 2.24,1.375 2.479,1.531 0.24,0.156 10 false 1 2.24,1.875 2.344,2.031 0.104,0.156 10 false 2 2.24,2.385 2.344,2.542 0.104,0.156 10 false 3 5.167,1 5.563,1.156 0.396,0.156 10 false FRV+ 5.167,1.51 5.521,1.677 0.354,0.167 10 false FRV- 5.167,2.01 5.604,2.167 0.438,0.156 10 false SSFV 5.167,2.521 5.604,2.677 0.438,0.156 10 false SGND 4.896,0.802 5,0.958 0.104,0.156 10 false 8 4.896,1.313 5,1.469 0.104,0.156 10 false 5 4.896,1.813 5,1.969 0.104,0.156 10 false 3 4.896,2.323 5,2.479 0.104,0.156 10 false 1 1.177,2.854 1.458,3.01 0.281,0.156 10 false b16 1.177,3.021 2.448,3.177 1.271,0.156 10 false Front Vertical Motor 0.917,3.635 2.781,3.979 1.865,0.344 10 false Separate Type Front Seat Cushion Spring Assembly LH 4.802,3.635 6.594,3.792 1.792,0.156 10 false Front Power Seat Switch LH 4.823,1 5.083,1.156 0.26,0.156 10 false b18 4.823,1.5 5.083,1.656 0.26,0.156 10 false b18 4.823,2.01 5.083,2.167 0.26,0.156 10 false b19 4.823,2.521 5.083,2.677 0.26,0.156 10 false b19

PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (POWER SEAT MOTOR FUNCTION)
a.

Select the Active Test, use the GTS to generate a control command, and then check the power seat motor function (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>DATA LIST / ACTIVE TEST).

Driver Seat
Tester Display Test Part Control Range Diagnostic Note
Front Vertical Operation Seat front vertical operation Up / OFF / Down -

OK:

Motor operates normally.




OK

2.CHECK FRONT POWER SEAT SWITCH LH (FRONT VERTICAL MOTOR CIRCUIT)

NG

5.INSPECT SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY LH (FRONT VERTICAL MOTOR)
2.CHECK FRONT POWER SEAT SWITCH LH (FRONT VERTICAL MOTOR CIRCUIT)
a.
U149739E02
1.583,1.354 1.375,1.677 1.375,1.677 1.375,1.802 false 1.844,1.354 2.052,1.677 2.052,1.677 2.052,1.802 false 0.135,0.104 0.313,0.271 0.177,0.167 10 false *a 1.219,1.813 1.49,1.969 0.271,0.156 10 false O/P 1.875,1.813 2.198,1.969 0.323,0.156 10 false GND 0.417,1.073 0.667,1.229 0.25,0.156 10 false b16

Disconnect the b16 front vertical motor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
b16-2 (O/P) - b16-3 (GND) Front vertical switch on 4.8 to 5.1 V


Text in Illustration
*a Front view of wire harness connector
(to Separate Type Front Seat Cushion Spring Assembly LH [Front Vertical Motor])



OK

3.CHECK SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY LH (FRONT VERTICAL MOTOR)

NG

4.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH - FRONT VERTICAL MOTOR)
3.CHECK SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY LH (FRONT VERTICAL MOTOR)
a.
U149848E02
1.844,1.469 1.844,1.875 false 0.156,0.188 0.333,0.354 0.177,0.167 10 false *a 1.698,1.896 2.021,2.052 0.323,0.156 10 false O/P 0.333,1.24 0.604,1.396 0.271,0.156 10 false b16

Connect the b16 front vertical motor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
b16-2 (O/P) - Body ground Front vertical switch on 4.5 to 4.8 V


Text in Illustration
*a Component with harness connected
(Separate Type Front Seat Cushion Spring Assembly LH [Front Vertical Motor])



OK

REPLACE FRONT POWER SEAT SWITCH LH

NG

REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY LH (FRONT VERTICAL MOTOR)

4.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH - FRONT VERTICAL MOTOR)
a.

Disconnect the b19 front power seat switch LH connector.


b.

Disconnect the b16 front vertical motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
b19-3 (SSFV) - b16-2 (O/P) Always Below 1 Ω
b19-1 (SGND) - b16-3 (GND) Always Below 1 Ω
b19-3 (SSFV) - Body ground Always 10 kΩ or higher
b19-1 (SGND) - Body ground Always 10 kΩ or higher




OK

REPLACE FRONT POWER SEAT SWITCH LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY LH (FRONT VERTICAL MOTOR)
a.
B238256E22
1.99,1.292 1.99,1.625 false 1.448,1.281 1.448,1.615 false 1.365,1.656 1.833,1.813 0.469,0.156 10 false UP 1.823,1.667 2.292,1.844 0.469,0.177 10 false DOWN 0.094,0.115 0.563,0.271 0.469,0.156 10 false *a

Remove the separate type front seat cushion spring assembly LH (front vertical motor) (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>DISASSEMBLY).


b.

Disconnect the b16 front vertical motor connector.


c.

Check if the seat cushion spring moves smoothly when the battery is connected to the front vertical motor connector terminals.

OK:
Measurement Condition Operational Direction
Battery positive (+) → 4 (UP)
Battery negative (-) → 1 (DOWN)
Seat cushion spring moves upward
Battery positive (+) → 1 (DOWN)
Battery negative (-) → 4 (UP)
Seat cushion spring moves downward


Text in Illustration
*a Component without harness connected
(Separate Type Front Seat Cushion Spring Assembly LH [Front Vertical Motor])



OK

6.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH - FRONT VERTICAL MOTOR)

NG

REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY LH (FRONT VERTICAL MOTOR)

6.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH - FRONT VERTICAL MOTOR)
a.

Disconnect the b18 front power seat switch LH connector.


b.

Disconnect the b16 front vertical motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
b18-8 (FRV+) - b16-4 (UP) Always Below 1 Ω
b18-5 (FRV-) - b16-1 (DOWN) Always Below 1 Ω
b18-8 (FRV+) - Body ground Always 10 kΩ or higher
b18-5 (FRV-) - Body ground Always 10 kΩ or higher




OK

REPLACE FRONT POWER SEAT SWITCH LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR