Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) › from 2013.08
RM1440E _58 Vehicle Interior _056161 SEAT _0274116 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) C

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  B2653  Lifter Sensor Malfunction  


DESCRIPTION

When the front power seat switch LH does not receive a sensor signal despite upward or downward movement of the seat by power seat motor operation, this DTC is stored.

DTC Code DTC Detection Condition Trouble Area
B2653 The upward and downward lock detection position of the sensor is the same.
·

Front power seat switch LH

·

Separate type front seat cushion spring assembly LH (Lifter motor)

·

Harness or connector



WIRING DIAGRAM

B357484E09
1.917,0.979 2.135,1.135 0.219,0.156 10 false UP 1.677,1.479 2.146,1.646 0.469,0.167 10 false DOWN 1.875,1.99 2.135,2.146 0.26,0.156 10 false O/P 1.802,2.49 2.135,2.646 0.333,0.156 10 false GND 2.24,0.865 2.344,1.021 0.104,0.156 10 false 1 2.24,1.365 2.344,1.521 0.104,0.156 10 false 4 2.24,1.875 2.344,2.031 0.104,0.156 10 false 2 2.24,2.385 2.344,2.542 0.104,0.156 10 false 3 5.167,1 5.563,1.156 0.396,0.156 10 false LFT+ 5.167,1.5 5.521,1.667 0.354,0.167 10 false LFT- 5.167,2.01 5.604,2.167 0.438,0.156 10 false SSRL 5.167,2.51 5.604,2.667 0.438,0.156 10 false SGND 4.865,0.802 5.052,0.958 0.188,0.156 10 false 10 4.865,1.302 5.042,1.458 0.177,0.156 10 false 12 4.896,1.813 5,1.969 0.104,0.156 10 false 4 4.896,2.323 5,2.479 0.104,0.156 10 false 1 1.323,2.865 1.583,3.031 0.26,0.167 10 false b17 1.323,3.031 2.063,3.188 0.74,0.156 10 false Lifter Motor 0.906,3.635 2.75,3.979 1.844,0.344 10 false Separate Type Front Seat Cushion Spring Assembly LH 4.781,3.635 6.563,3.792 1.781,0.156 10 false Front Power Seat Switch LH 4.823,1 5.073,1.156 0.25,0.156 10 false b18 4.823,1.5 5.073,1.656 0.25,0.156 10 false b18 4.823,2.01 5.073,2.167 0.25,0.156 10 false b19 4.823,2.521 5.073,2.677 0.25,0.156 10 false b19

PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (POWER SEAT MOTOR FUNCTION)
a.

Select the Active Test, use the GTS to generate a control command, and then check the power seat motor function (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>DATA LIST / ACTIVE TEST).

Tester Display Test Part Control Range Diagnostic Note
Lifter Operation Seat lifter operation Up / OFF / Down -

OK:

Motor operates normally.




OK

2.CHECK FRONT POWER SEAT SWITCH LH (LIFTER MOTOR CIRCUIT)

NG

5.INSPECT SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY LH (LIFTER MOTOR)
2.CHECK FRONT POWER SEAT SWITCH LH (LIFTER MOTOR CIRCUIT)
a.
U149740E02
1.583,1.354 1.375,1.677 1.375,1.677 1.375,1.802 false 1.844,1.354 2.052,1.677 2.052,1.677 2.052,1.802 false 0.135,0.104 0.313,0.271 0.177,0.167 10 false *a 1.219,1.813 1.49,1.969 0.271,0.156 10 false O/P 1.875,1.813 2.198,1.969 0.323,0.156 10 false GND 0.448,1.052 0.708,1.208 0.26,0.156 10 false b17

Disconnect the b17 lifter motor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
b17-2 (O/P) - b17-3 (GND) Lifter switch on 4.8 to 5.1 V


Text in Illustration
*a Front view of wire harness connector
(to Separate Type Front Seat Cushion Spring Assembly LH [Lifter Motor])



OK

3.CHECK SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY LH (LIFTER MOTOR)

NG

4.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - LIFTER MOTOR)
3.CHECK SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY LH (LIFTER MOTOR)
a.
U149849E02
1.844,1.469 1.844,1.875 false 0.156,0.188 0.333,0.354 0.177,0.167 10 false *a 1.719,1.896 2.042,2.052 0.323,0.156 10 false O/P 0.333,1.229 0.604,1.385 0.271,0.156 10 false b17

Connect the b17 lifter motor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
b17-2 (O/P) - Body ground Lifter switch on 4.5 to 4.8 V


Text in Illustration
*a Component with harness connected
(Separate Type Front Seat Cushion Spring Assembly LH [Lifter Motor])



OK

REPLACE FRONT POWER SEAT SWITCH LH

NG

REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY LH (LIFTER MOTOR)

4.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - LIFTER MOTOR)
a.

Disconnect the b19 front power seat switch LH connector.


b.

Disconnect the b17 lifter motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
b19-4 (SSRL) - b17-2 (O/P) Always Below 1 Ω
b19-1 (SGND) - b17-3 (GND) Always Below 1 Ω
b19-4 (SSRL) - Body ground Always 10 kΩ or higher
b19-1 (SGND) - Body ground Always 10 kΩ or higher




OK

REPLACE FRONT POWER SEAT SWITCH LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY LH (LIFTER MOTOR)
a.
B238256E23
1.99,1.292 1.99,1.625 false 1.458,1.302 1.458,1.635 false 1.198,1.688 1.667,1.844 0.469,0.156 10 false DOWN 1.885,1.667 2.104,1.833 0.219,0.167 10 false UP 0.156,0.094 0.375,0.26 0.219,0.167 10 false *a

Remove the separate type front seat cushion spring assembly LH (lifter motor) (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>DISASSEMBLY).


b.

Disconnect the b17 lifter motor connector.


c.

Check if the seat cushion spring moves smoothly when the battery is connected to the lifter motor connector terminals.

OK:
Measurement Condition Operational Direction
Battery positive (+) → 1 (UP)
Battery negative (-) → 4 (DOWN)
Seat cushion spring moves upward
Battery positive (+) → 4 (DOWN)
Battery negative (-) → 1 (UP)
Seat cushion spring moves downward


Text in Illustration
*a Component without harness connected
(Separate Type Front Seat Cushion Spring Assembly LH [Lifter Motor])



OK

6.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH - LIFTER MOTOR)

NG

REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY LH (LIFTER MOTOR)

6.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH - LIFTER MOTOR)
a.

Disconnect the b18 front power seat switch LH connector.


b.

Disconnect the b17 lifter motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
b18-10 (LFT+) - b17-1 (UP) Always Below 1 Ω
b18-12 (LFT-) - b17-4 (DOWN) Always Below 1 Ω
b18-10 (LFT+) - Body ground Always 10 kΩ or higher
b18-12 (LFT-) - Body ground Always 10 kΩ or higher




OK

REPLACE FRONT POWER SEAT SWITCH LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR