Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) › from 2013.08
RM1440E _58 Vehicle Interior _056161 SEAT _0274116 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) C

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  B2658  Short in Sensor with Motor Power Supply Circuit  


DESCRIPTION

This DTC is stored when a power seat motor operates (a position control sensor is being supplied with power) and the power supply voltage does not rise to the specified value.

DTC Code DTC Detection Condition Trouble Area
B2658 A problem with the voltage supplied to the position control sensor.
·

Front power seat switch LH

·

Separate type front seat cushion spring assembly LH

·

Separate type front seatback spring assembly LH

·

Harness or connector



WIRING DIAGRAM

B357485E02
1.353,1.546 2.217,1.725 0.864,0.179 10 b15 1.353,1.697 2.101,1.874 0.748,0.177 10 Slide Motor 1.92,0.673 2.187,0.840 0.267,0.166 10 O/P 5.222,1.226 5.691,1.392 0.468,0.166 10 SGND 5.222,0.673 5.691,0.840 0.468,0.166 10 SSRS 2.299,0.566 2.518,0.721 0.218,0.155 10 2 1.874,1.226 2.218,1.381 0.343,0.155 10 GND 2.299,1.115 2.518,1.270 0.218,0.155 10 3 5.001,0.566 5.096,0.721 0.095,0.155 10 5 1.353,7.115 1.538,7.294 0.185,0.179 10 d4 1.353,7.267 2.354,7.443 1.001,0.177 10 Reclining Motor 1.927,2.35 2.187,2.505 0.260,0.156 10 O/P 5.222,6.416 5.691,6.582 0.468,0.166 10 SSRR 2.299,2.241 2.518,2.396 0.218,0.155 10 2 1.874,2.736 2.218,2.889 0.343,0.153 10 GND 2.299,2.619 2.518,2.774 0.218,0.155 10 3 4.96,6.31 5.133,6.465 0.172,0.155 10 11 1.353,3.053 2.263,3.232 0.910,0.179 10 b16 1.353,3.205 2.602,3.381 1.250,0.177 10 Front Vertical Motor 1.94,3.862 2.218,4.015 0.278,0.153 10 O/P 5.222,2.349 5.691,2.516 0.468,0.166 10 SSFV 2.299,3.753 2.518,3.908 0.218,0.155 10 2 1.874,4.246 2.218,4.403 0.343,0.157 10 GND 2.299,4.137 2.518,4.292 0.218,0.155 10 3 5.001,2.241 5.096,2.396 0.095,0.155 10 3 1.356,4.562 2.285,4.741 0.929,0.179 10 b17 1.356,4.714 2.101,4.890 0.745,0.177 10 Lifter Motor 1.937,6.418 2.218,6.575 0.281,0.157 10 O/P 5.222,3.86 5.691,4.027 0.468,0.166 10 SSRL 2.299,6.31 2.518,6.465 0.218,0.155 10 2 1.874,6.805 2.218,6.959 0.343,0.154 10 GND 2.299,6.696 2.518,6.851 0.218,0.155 10 3 5.001,3.753 5.096,3.908 0.095,0.155 10 4 5.001,1.115 5.096,1.270 0.095,0.155 10 1 0.78,5.299 2.953,5.641 2.173,0.342 10 Separate Type Front Seat Cushion Spring Assembly LH 0.913,7.847 2.835,8.188 1.922,0.342 10 Separate Type Front Seatback Spring Assembly LH 4.833,8.021 6.627,8.186 1.795,0.165 10 Front Power Seat Switch LH 4.833,7.837 5.110,7.992 0.277,0.155 10 b19

PROCEDURE

1.CHECK FOR DTC

OK

NG

2.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH - SLIDE MOTOR)
2.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH - SLIDE MOTOR)
a.

Disconnect the b19 front power seat switch LH connector.


b.

Disconnect the b15 slide motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
b19-5 (SSRS) - b15-2 (O/P) Always Below 1 Ω
b19-1 (SGND) - b15-3 (GND) Always Below 1 Ω
b19-5 (SSRS) - b19-1 (SGND) Always 10 kΩ or higher
b19-5 (SSRS) - Body ground Always 10 kΩ or higher
b19-1 (SGND) - Body ground Always 10 kΩ or higher




OK

3.CHECK FRONT POWER SEAT SWITCH LH (SLIDE MOTOR CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK FRONT POWER SEAT SWITCH LH (SLIDE MOTOR CIRCUIT)
a.
U149741E02
1.583,1.354 1.375,1.677 1.375,1.677 1.375,1.802 false 1.833,1.354 2.042,1.677 2.042,1.677 2.042,1.802 false 0.135,0.104 0.313,0.271 0.177,0.167 10 false *a 1.219,1.813 1.542,1.969 0.323,0.156 10 false O/P 1.875,1.813 2.198,1.969 0.323,0.156 10 false GND 0.313,1.156 0.563,1.313 0.25,0.156 10 false b15

Connect the b19 front power seat switch LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
b15-2 (O/P) - b15-3 (GND) Sliding switch on 4.8 to 5.1 V


Text in Illustration
*a Front view of wire harness connector
(to Separate Type Front Seat Cushion Spring Assembly LH [Slide Motor])



OK

4.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH - FRONT VERTICAL MOTOR)

NG

REPLACE FRONT POWER SEAT SWITCH LH

4.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH - FRONT VERTICAL MOTOR)
a.

Disconnect the b19 front power seat switch LH connector.


b.

Disconnect the b16 front vertical motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
b19-3 (SSFV) - b16-2 (O/P) Always Below 1 Ω
b19-1 (SGND) - b16-3 (GND) Always Below 1 Ω
b19-3 (SSFV) - b19-1 (SGND) Always 10 kΩ or higher
b19-3 (SSFV) - Body ground Always 10 kΩ or higher
b19-1 (SGND) - Body ground Always 10 kΩ or higher




OK

5.CHECK FRONT POWER SEAT SWITCH LH (FRONT VERTICAL MOTOR CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK FRONT POWER SEAT SWITCH LH (FRONT VERTICAL MOTOR CIRCUIT)
a.
U149742E02
1.583,1.354 1.375,1.677 1.375,1.677 1.375,1.802 false 1.833,1.354 2.042,1.677 2.042,1.677 2.042,1.802 false 0.135,0.104 0.313,0.271 0.177,0.167 10 false *a 1.219,1.813 1.49,1.969 0.271,0.156 10 false O/P 1.875,1.813 2.198,1.969 0.323,0.156 10 false GND 0.417,1.083 0.677,1.24 0.26,0.156 10 false b16

Connect the b19 front power seat switch LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
b16-2 (O/P) - b16-3 (GND) Front vertical switch on 4.8 to 5.1 V


Text in Illustration
*a Front view of wire harness connector
(to Separate Type Front Seat Cushion Spring Assembly LH [Front Vertical Motor])



OK

6.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH - LIFTER MOTOR)

NG

REPLACE FRONT POWER SEAT SWITCH LH

6.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH - LIFTER MOTOR)
a.

Disconnect the b19 front power seat switch LH connector.


b.

Disconnect the b17 lifter motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
b19-4 (SSRL) - b17-2 (O/P) Always Below 1 Ω
b19-1 (SGND) - b17-3 (GND) Always Below 1 Ω
b19-4 (SSRL) - b19-1 (SGND) Always 10 kΩ or higher
b19-4 (SSRL) - Body ground Always 10 kΩ or higher
b19-1 (SGND) - Body ground Always 10 kΩ or higher




OK

7.CHECK FRONT POWER SEAT SWITCH LH (LIFTER MOTOR CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK FRONT POWER SEAT SWITCH LH (LIFTER MOTOR CIRCUIT)
a.
U149743E02
1.583,1.354 1.375,1.677 1.375,1.677 1.375,1.802 false 1.833,1.354 2.042,1.677 2.042,1.677 2.042,1.802 false 0.135,0.104 0.313,0.271 0.177,0.167 10 false *a 1.219,1.813 1.49,1.969 0.271,0.156 10 false O/P 1.875,1.813 2.198,1.969 0.323,0.156 10 false GND 0.458,1.052 0.719,1.208 0.26,0.156 10 false b17

Connect the b19 front power seat switch LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
b17-2 (O/P) - b17-3 (GND) Lifter switch on 4.8 to 5.1 V


Text in Illustration
*a Front view of wire harness connector
(to Separate Type Front Seat Cushion Spring Assembly LH [Lifter Motor])



OK

8.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH - RECLINING MOTOR)

NG

REPLACE FRONT POWER SEAT SWITCH LH

8.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH - RECLINING MOTOR)
a.

Disconnect the b19 front power seat switch LH connector.


b.

Disconnect the d4 reclining motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
b19-11 (SSRR) - d4-2 (O/P) Always Below 1 Ω
b19-1 (SGND) - d4-3 (GND) Always Below 1 Ω
b19-11 (SSRR) - b19-1 (SGND) Always 10 kΩ or higher
b19-11 (SSRR) - Body ground Always 10 kΩ or higher
b19-1 (SGND) - Body ground Always 10 kΩ or higher




OK

9.CHECK FRONT POWER SEAT SWITCH LH (RECLINING MOTOR CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK FRONT POWER SEAT SWITCH LH (RECLINING MOTOR CIRCUIT)
a.
U180722E02
1.583,1.354 1.375,1.677 1.375,1.677 1.375,1.802 false 1.833,1.354 2.042,1.677 2.042,1.677 2.042,1.802 false 0.135,0.104 0.313,0.271 0.177,0.167 10 false *a 1.219,1.813 1.49,1.969 0.271,0.156 10 false O/P 1.875,1.813 2.198,1.969 0.323,0.156 10 false GND 0.354,1.104 0.531,1.26 0.177,0.156 10 false d4

Connect the b19 front power seat switch LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
d4-2 (O/P) - d4-3 (GND) Reclining switch on 4.8 to 5.1 V


Text in Illustration
*a Front view of wire harness connector
(to Separate Type Front Seatback Spring Assembly LH [Reclining Motor])



OK

10.CHECK SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY LH

NG

REPLACE FRONT POWER SEAT SWITCH LH

10.CHECK SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY LH
a.

Temporarily replace the separate type front seat cushion spring with a new or normally functioning one (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>DISASSEMBLY).



c.

Check for DTCs (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>DTC CHECK / CLEAR).

OK:

DTC B2658 is not output.




OK

END (SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY LH IS DEFECTIVE)

NG

11.CHECK SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY LH
11.CHECK SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY LH
a.

Temporarily replace the separate type front seatback spring with a new or normally functioning one (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>DISASSEMBLY).



c.

Check for DTCs (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>DTC CHECK / CLEAR).

OK:

DTC B2658 is not output.




OK

END (SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY LH IS DEFECTIVE)

NG

REPLACE FRONT POWER SEAT SWITCH LH