Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)
RM1440E _58 Vehicle Interior _056163 HEATING / AIR CONDITIONING _0274151 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  B1442/42  Air Inlet Damper Control Servo Motor Circuit  


DESCRIPTION

The recirculation damper servo sub-assembly sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on the signals to move the air inlet damper to any position, which controls the intake air settings (fresh, fresh/recirculation and recirculation).

HINT:

Confirm that no mechanical problem is present because this trouble code may be stored when either a damper link or damper is mechanically locked.


DTC Code DTC Detection Condition Trouble Area
B1442/42 The air inlet damper position does not change when the air conditioning amplifier assembly operates the recirculation damper servo sub-assembly.
·

Recirculation damper servo sub-assembly

·

Air conditioning harness assembly

·

Air conditioning amplifier assembly



WIRING DIAGRAM

E353387E02
0.625,2.073 2.385,2.438 1.76,0.365 10 false Recirculation Damper Servo Sub-assembly 2.969,2.146 5.188,2.365 2.219,0.219 10 false Air Conditioning Harness Assembly 3.167,1.063 3.406,1.26 0.24,0.198 10 false IC 5.344,0.406 5.583,0.604 0.24,0.198 10 false 4 5.344,0.948 5.583,1.146 0.24,0.198 10 false 3 5.344,1.49 5.583,1.688 0.24,0.198 10 false 2 5.594,0.51 6.094,0.677 0.5,0.167 10 false B BUS 5.615,1.073 6.115,1.24 0.5,0.167 10 false BUS 5.604,1.604 6.104,1.771 0.5,0.167 10 false BUS G 5.594,2.031 6.094,2.198 0.5,0.167 10 false z14 5.583,2.219 6.823,2.604 1.24,0.385 10 false Air Conditioning Amplifier Assembly

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (RECIRCULATION DAMPER SERVO)
a.

Use the Data List to check if the recirculation damper servo sub-assembly is functioning properly (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>DATA LIST / ACTIVE TEST).

Air Conditioner
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Air Inlet Damper Targ Pulse Recirculation damper servo sub-assembly target pulse / Min.: 0, Max.: 255 7 (pulse): Recirculation
28 (pulse): Fresh
-
Air Inlet Damper Actual Pulse Recirculation damper servo sub-assembly actual pulse / Min.: 0, Max.: 255 7 (pulse): Recirculation
28 (pulse): Fresh
-

OK:

The display is as specified in the normal condition column.


Result
Result Proceed to
OK (When troubleshooting according to problem symptoms table) A
OK (When troubleshooting according to the DTC) B
NG C



A

B

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

C

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (RECIRCULATION DAMPER SERVO)
2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (RECIRCULATION DAMPER SERVO)
a.

Select the Active Test, use the intelligent tester to generate a control command, and then check that the recirculation damper servo sub-assembly operates (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>DATA LIST / ACTIVE TEST).

Air Conditioner
Tester Display Test Part Control Range Diagnostic Note
Air Inlet Damper Targ Pulse Recirculation damper servo sub-assembly target pulse Min.: 0, Max.: 255 -

OK:

Recirculation damper servo sub-assembly operates normally.




OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

3.REPLACE RECIRCULATION DAMPER SERVO SUB-ASSEMBLY
3.REPLACE RECIRCULATION DAMPER SERVO SUB-ASSEMBLY
a.

Replace the recirculation damper servo sub-assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>BLOWER UNIT>DISASSEMBLY).

HINT:

Since the recirculation damper servo sub-assembly cannot be inspected while it is removed from the vehicle, replace the recirculation damper servo sub-assembly with a new or normally functioning one.




NEXT

4.CHECK FOR DTC
4.CHECK FOR DTC

OK

END (RECIRCULATION DAMPER SERVO SUB-ASSEMBLY IS FAULTY)

NG

5.REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY
5.REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY
a.

Temporarily replace the air conditioning amplifier assembly with a new or normally functioning one (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL).



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC

OK

END (AIR CONDITIONING AMPLIFIER ASSEMBLY IS FAULTY)

NG

REPLACE AIR CONDITIONING HARNESS ASSEMBLY