Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) › 2009.08–2013.08
RM1440E _58 Vehicle Interior _056163 HEATING / AIR CONDITIONING _0274151 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  B1443/43  Air Outlet Damper Control Servo Motor Circuit  


DESCRIPTION

The damper servo sub-assembly (mode damper servo) sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on the signals to move the air outlet damper to any position, which controls the air outlet changes.

HINT:

Confirm that no mechanical problem is present because this trouble code may be stored when either a damper link or damper is mechanically locked.


DTC Code DTC Detection Condition Trouble Area
B1443/43 The air outlet damper position does not change when the air conditioning amplifier assembly operates the damper servo sub-assembly (mode damper servo).
·

Damper servo sub-assembly (mode damper servo)

·

Air conditioning harness assembly

·

Air conditioning amplifier assembly



WIRING DIAGRAM

E353387E03
0.625,2.073 2.417,2.438 1.792,0.365 10 false Damper Servo Sub-assembly (Mode Damper Servo) 2.969,2.146 5.188,2.365 2.219,0.219 10 false Air Conditioning Harness Assembly 3.167,1.063 3.406,1.26 0.24,0.198 10 false IC 5.344,0.406 5.583,0.604 0.24,0.198 10 false 4 5.344,0.948 5.583,1.146 0.24,0.198 10 false 3 5.344,1.49 5.583,1.688 0.24,0.198 10 false 2 5.594,0.51 6.094,0.677 0.5,0.167 10 false B BUS 5.615,1.073 6.115,1.24 0.5,0.167 10 false BUS 5.604,1.604 6.104,1.771 0.5,0.167 10 false BUS G 5.594,2.031 6.094,2.198 0.5,0.167 10 false z14 5.583,2.219 6.823,2.604 1.24,0.385 10 false Air Conditioning Amplifier Assembly

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (MODE DAMPER SERVO)
a.

Use the Data List to check if the damper servo sub-assembly (mode damper servo) is functioning properly (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>DATA LIST / ACTIVE TEST).

Air Conditioner
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Air Outlet Servo Pulse (D) Damper servo sub-assembly (mode damper servo) actual pulse / Min.: 0, Max.: 255 15 (pulse): FACE 1
23 (pulse): FACE 2
41 (pulse): B/L
65 or 73 (pulse): FOOT
83 or 95 (pulse): F/D
113 (pulse): DEF
-
Air Outlet Servo Actu Pulse (D) Damper servo sub-assembly (mode damper servo) actual pulse / Min.: 0, Max.: 255 15 (pulse): FACE 1
23 (pulse): FACE 2
41 (pulse): B/L
65 or 73 (pulse): FOOT
83 or 95 (pulse): F/D
113 (pulse): DEF
-

OK:

The display is as specified in the normal condition column.


Result
Result Proceed to
OK (When troubleshooting according to problem symptoms table) A
OK (When troubleshooting according to the DTC) B
NG C



A

B

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

C

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (MODE DAMPER SERVO)
2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (MODE DAMPER SERVO)
a.

Select the Active Test, use the intelligent tester to generate a control command, and then check that the damper servo sub-assembly (mode damper servo) operates (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>DATA LIST / ACTIVE TEST).

Air Conditioner
Tester Display Test Part Control Range Diagnostic Note
Air Outlet Servo Pulse (D) Damper servo sub-assembly (mode damper servo) pulse Min.: 0, Max.: 255 -

OK:

Damper servo sub-assembly (mode damper servo) operates normally.




OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

3.REPLACE DAMPER SERVO SUB-ASSEMBLY (MODE DAMPER SERVO)
3.REPLACE DAMPER SERVO SUB-ASSEMBLY (MODE DAMPER SERVO)
a.

Replace the damper servo sub-assembly (mode damper servo) (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>DISASSEMBLY).

HINT:

Since the damper servo sub-assembly (mode damper servo) cannot be inspected while it is removed from the vehicle, replace the damper servo sub-assembly (mode damper servo) with a new or normally functioning one.




NEXT

4.CHECK FOR DTC
4.CHECK FOR DTC

OK

END (DAMPER SERVO SUB-ASSEMBLY [MODE DAMPER SERVO] IS FAULTY)

NG

5.REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY
5.REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY
a.

Temporarily replace the air conditioning amplifier assembly with a new or normally functioning one (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL).



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC

OK

END (AIR CONDITIONING AMPLIFIER ASSEMBLY IS FAULTY)

NG

REPLACE AIR CONDITIONING HARNESS ASSEMBLY