Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)
RM1440E _58 Vehicle Interior _056163 HEATING / AIR CONDITIONING _0274152 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  Blower Motor Circuit  


DESCRIPTION

E353399E01
0.271,0.177 2.104,0.375 1.833,0.198 10 false Blower Level 1.073,0.583 1.281,0.75 0.208,0.167 10 false HI 1.073,1.042 1.281,1.208 0.208,0.167 10 false M 1.052,1.51 1.26,1.677 0.208,0.167 10 false LO 1.24,2.146 1.448,2.313 0.208,0.167 10 false 0 1.708,2.156 2.042,2.344 0.333,0.188 10 false Low 2.594,2.146 2.927,2.333 0.333,0.188 10 false High 1.833,2.385 2.656,2.583 0.823,0.198 10 false SI Duty (%) 4.167,0.469 5.344,0.667 1.177,0.198 10 false Duty Ratio (%) = 5.479,0.313 5.688,0.479 0.208,0.167 10 false T1 5.479,0.625 5.688,0.792 0.208,0.167 10 false T2 6.208,0.458 6.531,0.635 0.323,0.177 10 false 100 4.646,1.583 4.979,1.813 0.333,0.229 10 false Off 4.646,1.896 4.979,2.125 0.333,0.229 10 false On 5.177,1.208 5.385,1.375 0.208,0.167 10 false T1 5.302,2.313 5.51,2.479 0.208,0.167 10 false T2

The blower with fan motor sub-assembly operates according to signals from the air conditioning amplifier assembly. The blower with fan motor sub-assembly speed signals are transmitted by changes in the duty ratio.

Duty Ratio:

The duty ratio is the ratio of the blower with fan motor sub-assembly on time (T1) to the total of the blower with fan motor sub-assembly on and off time (T2).

The air conditioning amplifier assembly controls the blower with fan motor sub-assembly speed.

WIRING DIAGRAM

E198319E06
1.079,0.711 1.318,0.894 0.239,0.184 10 SI 1.051,1.652 1.318,1.845 0.267,0.193 10 +B 0.93,2.247 1.317,2.421 0.387,0.174 10 GND 1.342,0.604 1.572,0.815 0.230,0.211 10 2 1.342,1.552 1.572,1.764 0.230,0.211 10 3 1.342,2.17 1.572,2.381 0.230,0.211 10 1 0.207,2.9 0.567,3.066 0.360,0.165 10 F43 0.193,3.064 2.562,3.294 2.369,0.230 10 Blower with Fan Motor Sub-assembly 3.267,1.639 4.152,1.892 0.885,0.253 10 from Battery 5.619,0.576 5.831,0.745 0.211,0.170 10 23 5.596,2.201 5.807,2.371 0.211,0.170 10 14 5.9,0.69 6.223,0.860 0.323,0.170 10 BLW 5.9,2.321 6.320,2.519 0.420,0.198 10 GND 5.508,2.779 5.928,2.977 0.420,0.198 10 F42 5.508,2.939 7.122,3.289 1.614,0.350 10 Air Conditioning Amplifier Assembly 2.253,1.811 2.645,2.065 0.392,0.253 10 HTR

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (BLOWER WITH FAN MOTOR)
a.

Select the Active Test, use the intelligent tester to generate a control command, and then check that the blower with fan motor sub-assembly operates (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)>DATA LIST / ACTIVE TEST).

Air Conditioner
Tester Display Test Part Control Range Diagnostic Note
Blower Motor Blower with fan motor sub-assembly Min.: 0, Max.: 31 -

OK:

Blower with fan motor sub-assembly operates and blower motor speed changes.




OK

NG

2.CHECK HARNESS AND CONNECTOR (BLOWER WITH FAN MOTOR - BATTERY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (BLOWER WITH FAN MOTOR - BATTERY AND BODY GROUND)
a.
U181011E02
1.344,1.594 1.094,1.719 true 2.052,1.594 2.375,1.823 true 0.104,0.031 0.281,0.188 0.177,0.156 10 false *a 0.542,1.146 0.844,1.313 0.302,0.167 10 false F43 0.708,1.677 1.042,1.823 0.333,0.146 10 false GND 2.417,1.813 2.75,1.958 0.333,0.146 10 false +B

Disconnect the F43 motor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F43-3 (+B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F43-1 (GND) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Blower with Fan Motor Sub-assembly)


OK

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BLOWER WITH FAN MOTOR AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BLOWER WITH FAN MOTOR AND BODY GROUND)
a.

Disconnect the F42 amplifier connector.


b.

Disconnect the F43 motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F42-23 (BLW) - F43-2 (SI) Always Below 1 Ω
F42-23 (BLW) - Body ground Always 10 kΩ or higher
F42-14 (GND) - Body ground Always Below 1 Ω




OK

4.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (BLW SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (BLW SIGNAL)
a.
U181009E02
1.344,1.385 0.865,0.625 true 0.167,0.167 0.354,0.333 0.188,0.167 10 false *a 1.625,0.344 1.938,0.51 0.313,0.167 10 false F42 0.542,0.458 0.896,0.604 0.354,0.146 10 false GND 2.885,3.875 3.24,4.021 0.354,0.146 10 false GND 2.313,2.052 2.667,2.198 0.354,0.146 10 false BLW

Remove the air conditioning amplifier assembly with its connectors still connected (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL).


b.

Using an oscilloscope, check the waveform.

Measurement Condition
Item Content
Terminal No. (Symbol) F42-23 (BLW) - F42-14 (GND)
Tool Setting 1 V/DIV., 500 μs/DIV.
Condition Ignition switch ON
Blower switch LO

OK:

Waveform is as shown in the illustration.


Text in Illustration
*a Component with harness connected
(Air Conditioning Amplifier Assembly)

HINT:

Waveform varies with the blower level.




OK

5.REPLACE BLOWER WITH FAN MOTOR SUB-ASSEMBLY

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

5.REPLACE BLOWER WITH FAN MOTOR SUB-ASSEMBLY
a.

Replace the blower with fan motor sub-assembly with a new or normally functioning one (See page Vehicle Interior>HEATING / AIR CONDITIONING>FRONT BLOWER MOTOR>REMOVAL).


b.

Operate the blower with fan motor sub-assembly to check that it functions properly.

OK:

Blower with fan motor sub-assembly operates normally.




OK

END (BLOWER WITH FAN MOTOR SUB-ASSEMBLY IS FAULTY)

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY