Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)
RM1440E _58 Vehicle Interior _056163 HEATING / AIR CONDITIONING _0274152 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  Air Conditioning Control Panel Circuit  


DESCRIPTION

This circuit consists of the heater control assembly and air conditioning amplifier assembly. When the heater control assembly is operated, signals are transmitted to the air conditioning amplifier assembly through the LIN communication system.

If the LIN communication system malfunctions, the air conditioning amplifier assembly does not operate when the heater control assembly is operated.

WIRING DIAGRAM

E157369E34
5.564,0.845 5.874,1.026 0.310,0.181 10 LIN1 1.389,0.845 1.741,1.026 0.353,0.181 10 LIN1 1.463,1.364 1.708,1.545 0.245,0.181 10 IG+ 1.407,1.911 1.732,2.092 0.326,0.181 10 GND 3.744,1.376 5.218,1.550 1.474,0.174 10 from IG1 NO. 1 Relay 2.419,1.515 3.335,1.696 0.916,0.181 10 ECU-IG NO. 2 5.525,2.648 6.991,3.054 1.467,0.406 10 Air Conditioning Amplifier Assembly 5.525,2.47 5.853,2.639 0.328,0.169 10 F42 0.886,3.296 2.501,3.477 1.615,0.181 10 : LIN Communication Line 5.255,0.676 5.426,0.857 0.171,0.181 10 37 1.833,1.256 1.989,1.437 0.156,0.181 10 4 1.835,1.811 2.052,1.992 0.217,0.181 10 11 1.83,0.653 2.016,0.835 0.186,0.181 10 10 0.532,2.466 0.882,2.650 0.350,0.184 10 F29 0.532,2.623 2.132,2.849 1.600,0.226 10 Heater Control Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (HEATER CONTROL - AIR CONDITIONING AMPLIFIER)
a.

Disconnect the F42 amplifier connector.


b.

Disconnect the F29 control connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F29-10 (LIN1) - F42-37 (LIN1) Always Below 1 Ω
F29-10 (LIN1) - Body ground Always 10 kΩ or higher




OK

2.CHECK HARNESS AND CONNECTOR (HEATER CONTROL - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (HEATER CONTROL - BATTERY AND BODY GROUND)
a.
U181057E02
1.833,1.073 2.406,0.844 true 1.969,1.375 2.396,1.865 true 2.479,0.74 2.792,0.927 0.313,0.188 10 false IG+ 2.448,1.802 2.781,1.99 0.333,0.188 10 false GND 0.542,1.094 0.854,1.281 0.313,0.188 10 false F29 0.177,0.063 0.375,0.25 0.198,0.188 10 false *a

Disconnect the F29 control connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F29-4 (IG+) - F29-11 (GND) Ignition switch off Below 1 V
F29-4 (IG+) - F29-11 (GND) Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F29-11 (GND) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Heater Control Assembly)


OK

3.REPLACE HEATER CONTROL ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE HEATER CONTROL ASSEMBLY
a.

Replace the heater control assembly with a new or normally functioning one (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL>REMOVAL).


b.

Operate the heater control assembly to check that it functions properly.

OK:

Heater control assembly operates normally.




OK

END (HEATER CONTROL ASSEMBLY IS FAULTY)

NG